• Composites Research
• /
• 제34권3호
• /
• pp.143-147
• /
• 2021

유리섬유 복합재료(GFRP) 내부 미세 박리에서 나타나는 테라헤르츠(THz) 중첩 신호의 FWHM 분석을 통한 미세 박리 검출 기술을 연구하였다. 테라헤르츠 시간영역 분광(THz-TDS) 시스템의 반사모드를 통해 유리섬유 복합재료 내부의 미세 박리 크기 별 THz 신호를 측정하였고, 미세 박리 위치에서 반사되어 검출되는 THz 중첩 신호의 Full Width Half Maximum (FWHM) 값을 추출하였다. 이후, 유리섬유 복합재료의 복소굴절률을 측정하여 미세 박리 크기에 따른 미세 박리 위치에서의 THz 중첩 신호 및 FWHM 값을 계산하여 비교하였다. 이론적으로 계산된 THz 중첩 신호로부터 미세 박리 크기와 중첩 신호에서의 FWHM 값의 상관관계를 도출하였으며, 미세 박리 위치에서의 THz 신호로부터 추출된 FWHM의 분석을 통해 미세 박리 크기를 예측할 수 있었다.

• Steel and Composite Structures
• /
• 제42권5호
• /
• pp.685-697
• /
• 2022

In this paper, a vibration-based method using the change ratios of modal data and the experience-based learning algorithm is presented for quantifying the position, size, and interface layer of delamination in laminated composites. Three types of objective functions are examined and compared, including the ones using frequency changes only, mode shape changes only, and their combination. A fine three-dimensional FE model with constraint equations is utilized to extract modal data. A series of numerical experiments is carried out on an eight-layer quasi-isotropic symmetric (0/-45/45/90)s composited beam for investigating the influence of the objective function, the number of modal data, the noise level, and the optimization algorithms. Numerical results confirm that the frequency-and-mode-shape-changes-based technique yields excellent results in all the three delamination variables of the composites and the addition of mode shape information greatly improves the accuracy of interface layer prediction. Moreover, the EBL outperforms the other three state-of-the-art optimization algorithms for vibration-based delamination detection of composites. A laboratory test on six CFRP beams validates the frequency-and-mode-shape-changes-based technique and confirms again its superiority for delamination detection of composites.

• 보존과학회지
• /
• 제38권4호
• /
• pp.314-326
• /
• 2022

Investigation of conservation status, optical survey, infrared thermography, and ultrasonic examination were performed on Avalokitesvara Bodhisattva mural and Buddhist Monk Bodhidharma mural to determine the conservation status and physical properties. As a result of investigation of conservation status, the types of damage are largely divided into the wall and finishing layer damage, painting layer degradation, damage due to restoration materials, stains and contamination, and biological damage. As a result of the optical survey, drawing, stains, and repainted site were confirmed. Result of the infrared thermography, the delamination of the finishing layer was confirmed, and some locations and shapes of the wooden lath inside the wall were identified. The result of the 3D scanning, the deviation, and the separation of the wall was confirmed. As a result of ultrasonic examination, it was confirmed that the physical properties of the mural were identified and the ultrasonic speed was relatively low due to physical damage such as delamination and exfoliation of the finishing layer and cracking. Ultrasonic speed values were also high in some wall cracks or delamination, and it was confirmed by the infrared thermography results that the wooden lath inside the wall was located in those parts. It was possible to understand that the wooden lath inside the walls affects the ultrasonic speed during the ultrasonic examination. Therefore, management through periodic inspection of the relevant elements is necessary, and a countermeasure for damage that may occur in the future should be prepared along with intensive monitoring of the major damage identified in this diagnosis result.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.735-738
• /
• 2003

Downsizing electronics requires precision position control with an accuracy of sub-micron order, which demands development of ultra-fine displacive devices. Piezoelectric transducer is one of devices transferring electric field energy into mechanical energy and being capable for fine displacement control. The transducer has been widely used as fine Position control device Multilayer piezoelectric actuator, one of typical piezo-transducer, is fabricated by stacking alternatively ceramic and electrode layers several hundred times followed by cofiring process. Electrode material should be tolerable in the firing process maintaining at ceramic-sintering temperatures up to $1100{\sim}1300^{\circ}C$. Ag-Pd can be used as stable electrode material in heat treatment above $960^{\circ}C$. Besides, adding small quantity ceramic powder allow the actuator to be fabricated in a good shape by diminishing shrinkage difference between ceramic and electrode layers, resulting in avoidance of crack and delamination at and/or nearby interface between ceramic an electrode layers. This study presents synthesis of nano-oxide-added Ag/Pd powders and its feasibility to candidate material tolerable at high temperature. The powders were formed in a co-precipitation process of Ag and Pd in nano-oxide-dispersed solution where Ag and Pd precursors are melted in $HNO_3$ acid.

• 보존과학회지
• /
• 제34권2호
• /
• pp.107-118
• /
• 2018

직지사 대웅전 포벽화에 대한 보존상태 진단 및 재질분석 등 과학적 조사를 통해 벽화 보존방안 마련을 위한 연구를 실시하였다. 포벽화 보존상태 평가 결과, 채색층 열화 및 벽화면 오염 등의 손상이 큰 것으로 나타났으며, 벽체 균열 및 파손 그리고 층간 분리 등 벽체의 구조적 손상이 심화된 것으로 나타났다. 광학적 조사결과 밑그림 또는 덧칠의 흔적 등 채색층에서의 특이점은 확인되지 않았다. 벽화 별 초음파 탐상 속도는 표면 위치에 따라 낮게는 약 195.8 m/s부터 높게는 392.7 m/s까지 측정되어 위치에 따른 표면 물성을 비교할 수 있었으며, 적외선 열화상 촬영에서는 벽체 층간 분리 및 채색층 박리부위가 면밀하게 검출되어 손상에 대한 객관적인 파악이 가능하였다. 재질 분석 결과 벽체는 모래와 풍화토를 사용하여 제작한 것으로 확인되었으며, 벽체층은 모래와 세립사 이하 크기의 토양을 거의 5:5로 혼합하였고, 마감층은 중립사와 세립사를 약 6:4 비율로 혼합한 것으로 나타났다. 그러나 마감층의 경우 극세립사 이하 크기의 혼합비율이 벽체층에 비해 현저히 적은 것으로 나타났다. 직지사 대웅전 포벽화는 토벽체가 갖는 구조 특성과 함께 벽체층간 밀도 차이로 인해 벽체 파손과 층간 분리현상이 발생한 것으로 판단된다.

• Macromolecular Research
• /
• 제14권3호
• /
• pp.312-317
• /
• 2006

In the preparation of a polyacrylonitrile (PAN)/sodium montmorillonite (Na-MMT) nanocomposite via an in-situ polymerization method, macroazoinitiator (MAI) was intercalated in the gallery of Na-MMT to enhance the delamination of silicate layers by intergallery polymerization. The exfoliated fine dispersion observed by X-ray diffraction pattern and transmission electron microscopy, the enhanced tensile storage modulus and the thermal decomposition temperature showed that the intercalated MAI was effective in inducing intergallery polymerization and that a poly(ethylene glycol) block linked to a PAN block improved the dispersion of hydrophilic Na-MMT in the polymer matrix.

• 한국초전도ㆍ저온공학회논문지
• /
• 제16권2호
• /
• pp.1-6
• /
• 2014

The five-year national project in Japan for R&D of coated conductors and applications, named as the Materials and Power Applications of Coated Conductors (M-PACC) project, was finished at the end of FY2013. The project consists of four sub-themes as cable, transformer, SMES and coated conductors. In the theme of coated conductors, the fabrication process had been developed to satisfy the requirements from the applications such as in-field $I_c$ performance, low AC loss in the long tapes etc. Through the project, the remarkable progress was achieved as follows; a high in-field minimum $I_c$ value over 54A/cm-width under 3T at 77K was realized in a 200m long EuBCO tape with artificial pinning centers of $BaHfO_3$ by the pulsed laser deposition (PLD) technique on the IBAD template. On the other hand, the AC loss reduction was confirmed in the tapes fabricated by both PLD and the metal organic deposition (MOD) techniques by scribing 100m tapes into 10-filamments. Additionally, the mechanism of the delamination phenomenon was systematically investigated and the strength was improved by eliminating the origins of the weak points in the films. Through the development, all targeted goals were accomplished and the several results were appreciated as a world champion data.

• Steel and Composite Structures
• /
• 제48권3호
• /
• pp.305-320
• /
• 2023

The mechanical properties of polymeric composites are degraded under elevated temperatures due to the effect of temperature on the mechanical behavior of the resin and resin fiber interfaces. In this study, the effect of temperature on the impact response of the carbon fiber reinforced plastics (CFRP) was investigated at low-velocity impact (LVI) using a drop-weight impact tester machine. All the composite plates were fabricated using a vacuum infusion process with a stacking sequence of [45/0_2/-45/90_2]s, and a thickness of 2.9 mm. A group of the specimens was exposed to an environment with a temperature cycling at the range of -30 ℃ to 65 ℃. In addition, three other groups of the specimens were aged at ambient (28 ℃), -30 ℃, and 65 ℃ for ten days. Then all the conditioned specimens were subjected to LVI at three energy levels of 10, 15, and 20 J. To assess the behavior of the damaged composite plates, the force-time, force-displacement, and energy-time diagrams were analyzed at all temperatures. Finally, radiography, optical microscopy, and scanning electron microscopy (SEM) were used to evaluate the effect of the temperature and damages at various impact levels. Based on the results, different energy levels have a similar effect on the LVI behavior of the samples at various temperatures. Delamination, matrix cracking, and fiber failure were the main damage modes. Compared to the samples tested at room temperature, the reduction of temperature to -30 ℃ enhanced the maximum impact force and flexural stiffness while decreasing the absorbed energy and the failure surface area. The temperature increasing to 65 ℃ increased the maximum impact force and flexural stiffness while decreasing the absorbed energy and the failure surface area. Applying 200 thermal cycles at the range of -30 ℃ to 65 ℃ led to the formation of fine cracks in the matrix while decreasing the absorbed energy. The maximum contact force is recorded under cyclic temperature as 5.95, 6.51 and 7.14 kN, under impact energy of 10, 15 and 20 J, respectively. As well as, the minimum contact force belongs to the room temperature condition and is reported as 3.93, 4.94 and 5.71 kN, under impact energy of 10, 15 and 20 J, respectively.

• Coupled systems mechanics
• /
• 제11권1호
• /
• pp.15-32
• /
• 2022

The comprehensive understanding of the fiber reinforced polymer behavior requires the use of advanced non-destructive testing methods due to its heterogeneous microstructure and anisotropic mechanical proprieties. In addition, the material response under load is strongly associated with manufacturing defects (e.g., voids, inclusions, fiber misalignment, debonds, improper cure and delamination). Such imperfections and microstructures induce various damage mechanisms arising at different scales before macrocracks are formed. The origin of damage phenomena can only be fully understood with the access to underlying microstructural features. This makes X-ray Computed Tomography an appropriate imaging tool to capture changes in the bulk of fibrous materials. Moreover, Digital Volume Correlation (DVC) can be used to measure kinematic fields induced by various loading histories. The correlation technique relies on image contrast induced by microstructures. Fibrous composites can be reinforced by different fiber architectures that may lead to poor natural contrast. Hence, a priori analyses need to be performed to assess the corresponding DVC measurement uncertainties. This study aimed to evaluate measurement resolutions of global and regularized DVC for glass fiber reinforced polymers with different fiber architectures. The measurement uncertainties were evaluated with respect to element size and regularization lengths. Even though FE-based DVC could not reach the recommended displacement uncertainty with low spatial resolution, regularized DVC enabled for the use of fine meshes when applying appropriate regularization.

• 한국생산제조학회지
• /
• 제23권3호
• /
• pp.250-258
• /
• 2014

Due to recent industrial growth and development, there has been a high demand for light and highly durable materials. Therefore, a variety of new materials has been developed. These new materials include carbon fiber reinforced plastic (CFRP or CRP), which is a wear-, fatigue-, heat-, and corrosion-resistant material. Because of its advantageous properties, CFRP is widely used in diverse fields including sporting goods, electronic parts, and medical supplies, as well as aerospace, automobile, and ship materials. However, this new material has several problems, such as delamination around the inlet and outlet holes at drilling, fiber separation, and tearing on the drilled surface. Moreover, drill chips having a fine particulate shape are harmful to the work environment and engineers' health. In fact, they deeply penetrate into machine tools, causing the reduction of lifespan and performance degradation. In this study, CFRP woven and unidirectional prepregs were formed at $45^{\circ}$ and $90^{\circ}$, respectively, in terms of orientation angle. Using a high-speed steel drill and a TiAIN-coated drill, the two materials were tested in three categories: cutting force with respect to RPM and feed speed; shape changes around the input and outlet holes; and the shape of drill chips.