• Journal of Surface Science and Engineering
• /
• v.24 no.4
• /
• pp.206-214
• /
• 1991

In the basic study of selective electroless Ni plating of Si wafers, plating rate and physical properties are investigated to obtain optimum conditions of contact hole filling. Si wafers are excellently activated in the concentration of 0.5M IF, 1mM PdCl2, 2mM EDTA at $70^{\circ}C$, 90sec. The optimum condition of Ni-B deposition on p-type Si wafers is 0.1M NiSO4, 0.11M Citrate, $70^{\circ}C$, pH6.8, 8mM DMAB. The main factor in the sheet resistences variation of films is amorphous and on heat treating matrix was transformed into a stable phase (Ni+Ni3B) at $300-400^{\circ}C$. But pH or DMAB concentration in the plating solution doesn't play role of heat-affected phase change.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.293-296
• /
• 2008

Injection molding operation consists of filling, packing, and cooling phase. The highest pressure is involved during the packing phase among the operation phases. Cavity pressure depends upon velocity to pressure switchover time and magnitude of packing pressure. The cavity pressure is directly related to stress concentration in the cavity of mold. Thus the observation and control of cavity pressure is very important to prevent mold cracking. In this study, cavity pressures were observed for operational conditions using the commercial CAE software, Moldflow. Operational conditions were velocity to pressure switchover time and packing pressure. Cavity pressures were also measured directly during injection molding. Simulation and experimental results showed good agreement.

• Applied Biological Chemistry
• /
• v.36 no.2
• /
• pp.127-133
• /
• 1993

The concentrations of tocopherols and compositions of fatty acids during germination and maturation of soybean seeds were determined by HPLC and GC. In germination stages, when the length of seedling axis was about 10 cm, the contents of total tocopherols and lipids were the highest. At the early phase of pod filling on field condition, the concentration of ${\delta}-tocopherol$ in soybean seeds was the highest, but, in further pod filling, the content of ${\delta}-tocopherol$ decreased continuously, and ${\alpha}-$ and ${\gamma}-tocopherol$ increased. Accumulation of oil during pod filling seems to be determined at the beginning. There seem positive correlations between several tocopherol homologues and fatty acids.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.132-132
• /
• 2011

For the programming volume of PRAM, Ge2Sb2Te5(GST) thin films have been dominantly used and prepared by physical vapor deposition (PVD), chemical vapor deposition (CVD), atomic layer deposition (ALD). Among these methods, ALD is particularly considered as the most promising technique for the integration of PRAM because the ALD offers a superior conformality to PVD and CVD methods and a digital thickness control precisely to the atomic level since the film is deposited one atomic layer at a time. Meanwhile, although the IST has been already known as an optical data storage material, recently, it is known that the IST benefits multistate switching behavior, meaning that the IST-PRAM can be used for mutli-level coding, which is quite different and unique performance compared with the GST-PRAM. Therefore, it is necessary to investigate a possibility of the IST materials for the application of PRAM. So far there are many attempts to deposit the IST with MOCVD and PVD. However, it has not been reported that the IST can be deposited with the ALD method since the ALD reaction mechanism of metal organic precursors and the deposition parameters related with the ALD window are rarely known. Therefore, the main aim of this work is to demonstrate the ALD process for IST films with various precursors and the conformal filling of a nano size programming volume structure with the ALD?IST film for the integration. InSbTe (IST) thin films were deposited by ALD method with different precursors and deposition parameters and demonstrated conformal filling of the nano size programmable volume of cell structure for the integration of phase change random access memory (PRAM). The deposition rate and incubation time are 1.98 A/cycle and 25 cycle, respectively. The complete filling of nano size volume will be useful to fabricate the bottom contact type PRAM.

• Journal of the Korean Institute of Gas
• /
• v.27 no.3
• /
• pp.35-40
• /
• 2023

In order to prevent an ammonia container from bursting under conditions such as overcharging and abnormal temperature rise, it is necessary to prepare accident prevention measures through analysis of the operating mechanism of the Thermally Activated Pressure Relief Devices (TPRD) attached to the container. In this study, stress analysis acting on the ammonia container under pressurized conditions, density change analysis according to temperature change, and correlation between container filling amount and temperature and pressure change were presented. In addition, the maximum filling amount of the ammonia container was calculated, and the temperature and pressure at the filling amount were calculated through the phase equilibrium diagram. Based on this, the appropriate melting point of the Thermally Activated Pressure Relief Devices was derived and verified through a melting temperature experiment. Based on the results of this study, conditions for preventing ammonia container rupture accidents were suggested.

• Economic and Environmental Geology
• /
• v.17 no.2
• /
• pp.91-100
• /
• 1984

The Gwangyang gold deposits geologically consist of granitic gneiss, metatectic gneiss and porphyroblastic gneiss which correspond to Jirisan gneiss complex. The formations of Gyeongsang system lies unconformably on these gneisses and are intruded by diorite, porphyritic andesite and Bulgugsa granites. Goheung districts are composed of quartz schist, andesitic rock, tuff and granite. The Gwangyang gold deposits are gold bearing fissure filling veins. The vein thickness varies from 15cm to 40cm and they consist of 7-10 layers in parallel. The Goheung copper deposits are sulphide bearing quartz veln which filled the fracture in andesitic rock and biotite granite. The contact zone of these rocks is partially altered. The mineral paragenesis of the Gwangyang and Goheung districts is pyrite, arsenopyrite, pyrrhotite, chalcopyrite, sphalerite, galena, sericite, quartz and calcite. The variation trends of FMA and A'KF triangular diagrams and the differentiation index (norm, Q + Or + Ab) versus oxides diagrams is similar to the Gyeonsang basin igneous rocks. From the trace element analysis of 10 samples of country rocks, wall rocks and veins, the distribution of copper and lead contents display a correlative distribution pattern in relation to gold and silver. Homogenization temperature of fluid inclusions range from $200^{\circ}C$ to $270^{\circ}C$ in quartz from the Gwangyang gold vein and the size of fluid inclusion range from 0.01mm to 0.04mm. The fluid inclusions are mainly one or two phase and the filling degree of the inclusions varies from 85 to 95.

• Asian Pacific Journal of Cancer Prevention
• /
• v.13 no.2
• /
• pp.493-497
• /
• 2012

This study was conducted to retrospectively evaluate the pattern of contrast enhancement with SonoVue on gray-scale ultrasonography of hepatic angiomyolipoma (HAML). Imaging features of 33 pathologically proven HAML lesions in 33 patients who underwent baseline ultrasound and contrast-enhanced ultrasonography (CEUS) were assessed retrospectively. All lesions were enhanced in the arterial phase and showed whole-tumor filling in. Thirty-two of 33 (97%) lesions showed early positive enhancement in the arterial phase. Twenty-three of these exhibited isoechoic or hyperechoic features in the portal phase. HAML demonstrate characteristic manifestations with SonoVue-enhanced real-time gray-scale ultrasonography.

• Journal of Powder Materials
• /
• v.21 no.5
• /
• pp.331-337
• /
• 2014

The effects of particle size of Li-Si alloy and LiCl-KCl addition as a binder phase for raw material of anode were investigated on the formability of the thermal battery anode. The formability was evaluated with respect to filling density, tap density, compaction density, spring-back and compressive strength. With increasing particle size of Li-Si alloy powder, densities increased while spring-back and compressive strength decreased. Since the small spring-back is beneficial to avoiding breakage of pressed compacts, larger particles might be more suitable for anode forming. The increasing amount of LiCl-KCl binder phase contributed to reducing spring-back, improving the formability of anode powder too. The control of particle size also seems to be helpful to get double pressed pellets, which consisted of two layer of anode and electrolyte.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.3
• /
• pp.101-106
• /
• 2003

The high temperature superconductor transformers gain interests from the industries. This paper described construction and test results of 10㎸A HTS transformer Three phase transformer with double pancake windings were constructed. To reduce the leakage magnetic field, secondary coil were placed between the two primary coils. BSCCO-2223 wire. silicon sheet steel core and FRP cryostats were used to construct the transformer. Three coils were stacked in one cryostat. Two double pancake coils were connected in series for the primary coil and one double pancake coil was used for the secondary coil. Total number of turns of the primary winding and the secondary winding were 112turns and 98urns, respectively, The rated voltages of each winding were 440/220V. The rated currents of each winding were 13.1/26.2A. After the tests of basic properties of the three phase HTS transformer using no-load test, short-circuit test and full-load test, continuous operation of 100 hours with pure resistive load has been carried out. Test results proved over-load capability and reliability of the HTS transformer.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.12
• /
• pp.60-65
• /
• 2001

To simulate the real molding conditions, the effects of phase change and compressibility of the resin were considered in the present investigation. A modified Cross model with either an Arrhenius-type or WLF-type functional form was used for modeling viscosity of the resin. A double-domain Tait equation of state was employed to describe the compressibility of the resin during molding. The energy balance equation including latent-heat dissipation fur semi-crystalline materials was solved in order to predict the solidified layer and temperature profile. Injection molding experiments were carried out using polypropylene(PP) in the present study. Based on the comparison between experiments and simulations, it was found out the predicted pressure distributions and melt front propagations were accurate. Thus it was concluded that the program developed in this study was proved to be useful in simulations of injection molding process.