• Journal of the Society of Disaster Information
• /
• v.20 no.2
• /
• pp.390-397
• /
• 2024

Purpose: In this study, PCM was used to give thermal performance to concrete and analyze its effect on durability to prevent disasters that may occur in concrete when exposed to hot and cold environments. Method: After preparing concrete specimens containing 10, 30, and 50% of the two types of PCMs compared to the cement volume, the pore volume, freeze melting resistance, and scaling resistance were evaluated. Result: Regardless of the type, when PCM powder was mixed with concrete, the amount of pores decreased, and when 10% and 30% were mixed, the freeze-melting resistance was also improved. It was also confirmed that the higher the mixing amount, the better the scaling resistance. Conclusion: When mixing powdered PCM into concrete, it is believed that durability can be improved to a certain level by the filling effect, and additional various studies should be supported for actual field application.

• Transactions of the Korean hydrogen and new energy society
• /
• v.35 no.3
• /
• pp.280-289
• /
• 2024

In this study, a cryogenic vessel was constructed to maintain and control the safe pressure of liquid hydrogen boil-off gas (BOG), and the numerical analysis was conducted on the development of computational fluid dynamics model inside the high-pressure vessel. An evaluation system was constructed using cryogenic inner and outer containers, pre-cooler, upper flange, and internal high-pressure container. We attempted to analyze the performance of the safety valve by injecting relatively high temperature hydrogen gas to generate BOG gas and quickly control the pressure of the high-pressure vessel up to 10 bar. As a results, the liquid volume fraction decreased with a rapid evaporation, and the pressure distribution increased monotonically inside a high pressure vessel. Additionally, it was found that the time to reach 10 bar was greatly affected by the filling rate of liquid hydrogen.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.144-149
• /
• 2014

Large residual stresses are remained in the conventional injection molded products because of the high cavity pressure in packing phase during injection molding process. Conventional injection molding (CIM) invokes distribution of cavity pressure and it has a limitation to obtain product with uniform physical property. Multi-cavity conventional injection molding contains quality deviation among the cavities since flow imbalance occurs during filling phase. Injection compression molding (ICM) is adopted to overcome these limitations of CIM. In this study, molding characteristics of CIM and ICM have been investigated using multi-cavity injection mold. Researches were performed by both experiment and computer simulation through observations of birefringence for transparent resins, polycarbonate and polystyrene in CIM and ICM. As a result, low and uniform birefringence and mold shrinkage were showed in the specimens by ICM that could give a uniform cavity pressure. Deviation of physical property among the specimens in multi-cavity mold shown in CIM was significantly reduced in the specimens by ICM. Through this study it was concluded that the ICM in multi-cavity molding was valid for molding products with uniform property in an individual cavity and also reduced property deviation among the cavities.

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.1
• /
• pp.163-173
• /
• 2010

A significant number of projects have been managed by US Army Corps of Engineers FED. Today, more information must be provided to the parties involved in the projects by phase than ever before. Specifically, USFK`s construction projects have been managed by FED(Far East District). Recently, however, large US private construction companies have been filling the role previously taken by FED. However, there is few construction managers to implement FED project in Korea. Accordingly, this study analyzes FED projects practices with focus on the construction management actors in order to suggest guideline. This study suggests a model FED construction process(Bid, Contract, Construction, As-Built Phase) by analyzing the existing FED project process using a IDEF0 methodology.

• Investigative Magnetic Resonance Imaging
• /
• v.5 no.1
• /
• pp.57-65
• /
• 2001

Purpose : $T_2$-weighted half courier Echo Planar Imaging (T2HEPI) method is proposed to reduce measurement time of existing EPI by a factor of 2. In addition, high $T_2$ contrast is obtained for clinical applications. High resolution single-shot EPI images with $T_2$ contrast are obtained with $128{\times}128$ matrix size by the proposed method. Materials and methods : In order to reduce measurement time in EPI, half courier space is measured, and rest of half courier data is obtained by conjugate symmetric filling. Thus high resolution single shot EPI image with $128{\times}128$ matrix size is obtained with 64 echoes. By the arrangement of phase encoding gradients, high $T_2$ weighted images are obtained. The acquired data in k-space are shifted if there exists residual gradient field due to eddy current along phase encoding gradient, which results in a serious problem in the reconstructed image. The residual field is estimated by the correlation coefficient between the echo signal for dc and the corresponding reference data acquired during the pre-scan. Once the residual gradient field is properly estimated, it can be removed by the adjustment of initial phase encoding gradient field between $70^{\circ}$ and $180^{\circ}$ rf pulses. Results : The suggested T2EPl is implemented in a 1.0 Tela whole body MRI system. Experiments are done with the effective echo times of 72ms and 96ms with single shot acquisitions. High resolution($128{\times}128$) volunteer head images with high $T_2$ contrast are obtained in a single scan by the proposed method. Conclusion : Using the half courier technique, higher resolution EPI images are obtained with matrix size of $128{\times}128$ in a single scan. Furthermore $T_2$ contrast is controlled by the effective echo time. Since the suggested method can be implemented by software alone (pulse sequence and corresponding tuning and reconstruction algorithms) without addition of special hardware, it can be widely used in existing MRI systems.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.28 no.1
• /
• pp.41-57
• /
• 1983

The effect of temperature 'during the reduction division stage on the Indica-Japonica rice varieties were studied in artificial temperature-controlled cabinets (Bioclimatic Laboratory). Varieties used were indica-japonica crosses (Suweon 264, Suweon 258, Milyang 29), indica (IR36, Lengkwang) and japonica rice (Jin-heung). The results obtained from this study are summarized as follows. The most sensitive stage to low temperature, the tetrad stage, was observed in each variety with the following auricle distance: Jinheung, -12cm; IR36, -3cm; Suweon264, -9cm; Suweon258, -3cm; Milyang29, -6cm and Lengkwang, +1cm. The tetrad stage occured when the palea elongation was about 50 to 60% of the final palea length at flowering stage in all varieties. The percentage of degenerated spikelets at tetrad as influenced by low-temperature treatment was very low in Jinheung and Lengkwang, but very high in IR36. In indica-japonica crosses only the 7-days treatments had a very high percentage. Between the 4-day and 7-day treatments as well as among all varieties, clear differences were observed in the low temperature induced sterility of 'special spikelets' (upper position grains at tetrad). In the 7-day treatments except in Lengkwang, all varieties showed very high sterility. It appears that the treatments is over the critical limit for treatment. However in the 4-day treatments, the intervarietal differences in sterility were very clear. In Jinheung, sterility was 46.8%; IR36, 67.6%; Suweon264, 60.9%, Milyang29, 62.2%; Lengkwang, 27.8%. A close relationship was observed between fertility and auricle distance. The lowest fertility of special spikelets was at the tetrad stage and the first contraction phase. Before and after the stage there was an increase in fertility. The palea length elongated nearly in a straight line from the spikelet formation stage to flowering. And there was a high correlation between palea length and auricle distance. distance.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.31 no.3
• /
• pp.516-526
• /
• 2004

Polymerization shrinkage of photoinitiation type composite resin cause several clinical problems. The purpose of this study was to evaluate the shrinkage strain stress, linear polymerization shrinkage, compressive strength and microhardness of recently developed composite resins. The composite resins were divided into four groups according to the contents of matrix and filler type. Group I : $Denfil^{TM}$(Vericom, Korea) with conventional matrix, Group II : $Charmfil^{(R)}$(Dentkist, Korea) with microfiller and nanofller mixture, Group III : $Filtek^{TM}$ Z250(3M-ESPE, USA) TEGDMA replaced by UDMA and Bis-EMA(6) in the matrix, and Group IV : $Filtek^{TM}$ Supreme(3M-ESPE, USA) using pure nanofiller. Preparation of acrylic molds were followed by filling and curing with light gun. Strain gauges were attached to each sample and the leads were connected to a strainmeter. With strainmeter shrinkage strain stress and linear polymerization shrinkage was measured for 10 minutes. The data detected at 1 minute and 10 minutes were analysed statistically with ONE-way ANOVA test. To evaluate the mechanical properties of tested materials, compressive hardness test and microhardness test were also rendered. The results can be summarized as follows : 1. Filling materials in acrylic molds showed initial temporary expansion in the early phase of polymerization. This was followed by contraction with the rapid increase in strain stress during the first 1 minute and gradually decreased during post-gel shrinkage phase. After 1 minute, there's no statistical differences of strain stress between groups. The highest strain stress was found in group IV and followed by group III, I, II at 10 minutes-measurement(p>.05). In regression analysis of strain stress, group III showed minimal inclination and followed by group II, I, IV during 1 minute. 2. In linear polymerization shrinkage test, the composite resins in every group showed initial increase of shrinkage velocity during the first 1 minute, followed by gradually decrease of shrinkage velocity. After 1 minute, group IV and group III showed statistical difference(p<.05). After 10 minutes, there were statistical differences between group IV and group I, III(p<.05) and between group II and group III(p<.05). In regression analysis of linear polymerization shrinkage, group II showed minimal inclination and followed by group IV, III, I during 1 minute. 3. In compressive strength test, group III showed the highest strength and followed by group II, IV, I. There were statistical differences between group III and group IV, I(p<.05). 4. In microhardness test, upper surfaces showed higher value than lower surfaces in every group(p<.05).

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.2
• /
• pp.57-62
• /
• 2011

The energy conversion efficiency of DSSCs (Dye-Sensitized Solar Cells) is dependent on the powder size, the structure, and the morphology of $TiO_2$ electrode. The higher efficiency is obtained with high surface area of the nanoanatase-$TiO_2$ powder adsorbed onto a lot more of the dye. Also, the enhancement of light scattering increases the efficiency with high adsorption of the dye. Powder size, crystalline phase, and shape of $TiO_2$ obtained by hydrothermal method have 15-20 nm, anatase and round. $TiO_2$ electrode has fabricated with the mixture of scattering $TiO_2$ particle with 0.4 ${\mu}m$ in nano-sized powder. Conversion efficiency of series of DSSCs was measured with volume fraction of scattering particle. Photovoltaic characteristics of DSSCs with 10% scattering particles are 3.51 mA for Jsc (short circuit current), 0.79 V for Voc(open circuit potential), filling factor 0.619 and 6.86% for efficiency. Jsc was improved by 11% and enhancement of efficiency by 0.77% compared with that of no scattering particles. The confinement of inserted light by light scattering particles has more increase of the injection of exiton(electron-hole pair) and decrease of moving path in electron. Efficiencies of DSSCs with more than 10% for scattering particles have reduced with increasing the pore in the $TiO_2$ electrode.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.27 no.2
• /
• pp.283-291
• /
• 2000

The purpose of this study was to compare the sedative effect of three routes of administration - intramuscular, intranasal drop-in, intranasal spray - with midazolam. The twenty two uncooperative children from 23 months to 76 months who required at least three dental appointment. Each patient was assigned randomly to receive intramuscular(Group I, 0.15mg/kg), intranasal drop-in(Group II, 0.20mg/kg), intranasal spray(Group III, 0.20mg/kg) administration at each visit. Sleep, crying, movement, and overall behavior response were evaluated, and the sedative effects were evaluated by Houpt's rating scale In order to monitor the sedated patients, pulse rate and peripheral oxygen saturation were measured by pulse oximeter during treatment procedures. The results were as follows 1. Pulse rate and peripheral oxygen saturation were stable through all the treatment procedures, and there were no statistically significant differences among three routes of administration(P>0.05). 2. The effect on sleep was, III, II, I, in order, III group was the most effective through all the treatment procedures, except rubber-dam placement and filling phase (P<0.0001). 3. The effects on crying, movement, overall behavior were II, III, I, in order, II group was the most effective through all treatment procedures(P<0.0001).

• Journal of the Mineralogical Society of Korea
• /
• v.21 no.1
• /
• pp.1-15
• /
• 2008

The Cretaceous Gajok gold-silver deposit within porphyry granite is located nearby the Cretaceous Pungam basin at the northeastern area in Republic of Korea. The Gajok gold-silver deposit is distinctively composed of a multiple-complex hydrothermal veins with comb, crustiform chalcedony quartz and vug textures, implying it was formed relatively shallower depth. The hypogene open-space filling veins could be divided into 5 paragenetic sequences, increasing tendency of Ag-rich electrum and Ag-phases with increasing paragenetic time. Electrum with high gold contents (${\sim}50$ atomic % Au) as well as sphalerite with high FeS contents (${\sim}6$ mole % FeS) are representative ore minerals in the middle stage. The late stage is characterized by silver-phase such like native silver and/or argentite, coexisting with Ag-rich electrum ($10{\sim}30$ atomic % Au) and Fe-poor sphalerite (< 1 mole % FeS). The ore-forming fluids evolution started at relatively high temperature and salinity (${\sim}360^{\circ}C$, ${\sim}7\;wt.%$ eq. NaCl) and were evolved by dilution and mixing mechanisms on the basis of fluid inclusion study. The gold-silver mineralization proceeded from ore-forming fluids containing greater amounts of less-evolved meteoric waters(${\delta}^{18}O$; $-0.6{\sim}-6.7\;%o$). These results imply that gold-silver mineralization of the Cretaceous Gaiok deposit formed at shallow-crustal level and could be categorized into low-sulfidation epithermal type, related to Cretaceous igneous activity.