• Journal of Advanced Navigation Technology
• /
• v.23 no.2
• /
• pp.97-103
• /
• 2019

In this paper, we designed and fabricated a receiving modem that can be applied to guided weapons can change real-time targets with little effect of fading. The designed modem consists of synchronous detector, timing error estimator, timing recovery, differential decoder and viterbi decoder, and it's implemented in FPGA so that it can be redesigned and modified according to requirements. The modem board was directly converted from IF frequency to baseband and converted into digital data through ADC. It is confirmed that it is applicable to the guided weapons that changing real-time targets through simulations, measurements and test.

• Nuclear Engineering and Technology
• /
• v.55 no.4
• /
• pp.1332-1341
• /
• 2023

Beam position measurement system can not only provide the beam position monitoring, but also be used for global orbit correction to reduce beam loss risk and maximize acceptance. The Beam Position Monitors (BPM) are installed along the synchrotron to acquire beam position with the front-end electronics and data acquisition system (DAQ). To realize high precision orbit measurement in the main heavy ion synchrotron and cooling storage ring of heavy-ion research facility in Lanzhou (HIRFL-CSRm), a series of alignment and calibration work has been implemented on the BPM and its DAQ system. This paper analyzed the tests performed in the laboratory as well as with beam based on the developed algorithms and hardware. Several filtering algorithms were designed and implemented on the acquired BPM raw data, then the beam position and resolution were calculated and analyzed. The results show that the position precision was significantly improved from more than 100 ㎛ to about 50 ㎛ by implementing the new designed filtering algorithm. According to the analyzation of the measurement results and upcoming physical requirements, further upgrade scheme for the BPM DAQ system of CSRm based on field programmable gate array (FPGA) technology was proposed and discussed.

• Journal of Advanced Navigation Technology
• /
• v.26 no.6
• /
• pp.441-447
• /
• 2022

In this paper, we propose a FLL-assisted-PLL based time synchronization algorithm for telemetry systems where frequency and phase errors exist in time synchronization pulse. The telemetry system may analyze the flight state by acquiring the state information in the distributed system. Therefor, in order to collect each state information without errors, precise time synchronization between the master and the slave is required. At this time, the master's time pulse have frequency and phase changes that can be caused by external and internal factors, so a method to maintain precision time synchronization is essential to provide telemetry data continuously. We propose the FLL-assisted-PLL based algorithm that is capable of high-speed synchronization and has high time synchronization accuracy. The proposed algorithm is verified through python simulation, and the VHDL Logic has been implemented in FPGA to check the performance according to the frequency errors and phase errors.

• Nuclear Engineering and Technology
• /
• v.56 no.1
• /
• pp.216-221
• /
• 2024

Ion cyclotron range of frequency (ICRF) heating system is an important auxiliary heating method in the experimental Advanced Superconducting Tokamak (EAST). In EAST, several megawatts of power are transmitted with coaxial transmission lines and coupled to the plasma. For the long pulse and high power operation of the ICRF waves heating system, it is very important to effectively control the power and initial phase of the ICRF signals. In this paper, a power and phase feedback control system is described based on field programmable gate array (FPGA) devices, which can realize complicated algorithms with the advantages of fast running and high reliability. The transmitted power and antenna phase are measured by a power and phase detector and digitized. The power and phase feedback control algorithms is designed to achieve the target power and antenna phase. The power feedback control system was tested on a dummy load and during plasma experiments. Test results confirm that the feedback control system can precisely control ICRF power and antenna phase and is robust during plasma variations.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.6
• /
• pp.431-441
• /
• 2003

This paper presents the design of 32 bit microprocessor for a sequence control using a field programmable gate array(FPGA). The microprocessor was designed by a VHDL with top down method, the program memory was separated from the data memory for high speed execution of sequence instructions. Therefore it was possible that sequence instructions could be operated at the same time during the instruction fetch cycle. In order to reduce the instruction decoding time and the interface time of the data memory interface, an instruction code size was implemented by 32 bits. And the real time debug operation was implemented for easeful debugging the designed processor with a single step run, PC break point run, data memory break point run. Also in this designed microprocessor, pulse instructions, step controllers, master controllers, BM and BCD type arithmetic instructions, barrel shift instructions were implemented for sequence logic control. The FPGA was synthesized under a Xilinx's Foundation 4.2i Project Manager using a V600EHQ240 which contains 600,000 gates. Finally simulation and experiment were successfully performed respectively. For showing good performance, the designed microprocessor for the sequence logic control was compared with the H8S/2148 microprocessor which contained many bit instructions for sequence logic control. The designed processor for the sequence logic showed good performance.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.468-470
• /
• 2002

We have designed X-ray detection system and multi-channel data acquisition system for Spiral CT application. X-ray detection system consists of scintillator and photodiode. Scintillator converts X-ray into visible light. Photodiode converts visible light into electrical signal. The multi-channel data acquisition system consists of analog, digital, master and backplane board. Analog board detects electrical signal and amplifies signal by 140dB. Digital board consists of MUX(Multiplex) which routes multi-channel analog signal to preamplifier, and ADC(Analog to Digital Converter) which converts analog signal into digital signal. Master board supplies the synchronized clock and transmits the digital data to image reconstructor. Backplane provides electrical power, analog output and clock signal. The system converts the projected X-ray signal over the detector array with large gain, samples the data in each channel sequentially, and the sampled data are transmitted to host computer in a given time frame. To meet the timing limitation, this system is very flexible since it is implemented by FPGA(Field Programmable Gate Array). This system must have a high-speed operation with low noise and high SNR(signal to noise ratio), wide dynamic range to get a high resolution image.

• Journal of KIISE
• /
• v.44 no.9
• /
• pp.932-945
• /
• 2017

In this paper, a new hardware and software architecture for a stereo vision processing system including rectification, disparity estimation, and visualization was developed. The developed method, named LArge scale stereo matching method using Support Point Interpolation (LASPI), shows excellence in real-time processing for obtaining dense disparity maps from high quality image regions that contain high density support points. In the real-time processing of high definition (HD) images, LASPI does not degrade the quality level of disparity maps compared to existing stereo-matching methods such as Efficient LArge-scale Stereo matching (ELAS). LASPI has been designed to meet a high frame-rate, accurate distance resolution performance, and a low resource usage even in a limited resource environment. These characteristics enable LASPI to be deployed to safety-critical applications such as an obstacle recognition system and distance detection system for autonomous vehicles. A Field Programmable Gate Array (FPGA) for the LASPI algorithm has been implemented in order to support parallel processing and 4-stage pipelining. From various experiments, it was verified that the developed FPGA system (Xilinx Virtex-7 FPGA, 148.5MHz Clock) is capable of processing 30 HD ($1280{\times}720pixels$) frames per second in real-time while it generates disparity maps that are applicable to real vehicles.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.8
• /
• pp.554-561
• /
• 2004

As the technologies of semiconductor and multimedia communication have been improved. the high-quality video and the multi-channel audio have been highlighted. MPEG Audio Layer 3 decoder has been implemented as a Processor using a standard. Since the synthesis filter of MPEG-1 Audio Layer 3 decoder requires the most outstanding operation in the entire decoder. the synthesis filter that can reduce the amount of operation is needed for the design of the high-speed processor. Therefore, in this paper, the synthesis filter. the most important part of MPEG Audio, is materialized in FPGA using the method of DAULT (distributed arithemetic look-up table). For the design of high-speed synthesis filter, the DAULT method is used instead of a multiplier and a Pipeline structure is used. The Performance improvement by 30% is obtained by additionally making the result of multiplication of data with cosine function into the table. All hardware design of this Paper are described using VHDL (VHIC Hardware Description Language) Active-HDL 6.1 of ALDEC is used for VHDL simulation and Synplify Pro 7.2V is used for Model-sim and synthesis. The corresponding library is materialized by XC4013E and XC4020EX. XC4052XL of XILINX and XACT M1.4 is used for P&R tool. The materialized processor operates from 20MHz to 70MHz.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.4
• /
• pp.37-47
• /
• 2016

The practical constraints on the commercial FPGAs which contain dedicated wide function multiplexers in their slice structure are incorporated with one of the most advanced FPGA mapping algorithms based on the AIG (And-Inverter Graph), one of the best logic representations in academia. As the first step of the mapping process, cuts are enumerated as intermediate structures. And then, the cuts which can be mapped to the multiplexers are recognized. Without any increased complexity, the delay and area of multiplexers as well as LUTs are calculated after checking the requirements for the tree construction such as symmetry and depth limit against dynamically changing mapping of neighboring nodes. Besides, the root positions of multiplexer trees are identified from the RTL code, and annotated to the AIG as AOs (Auxiliary Outputs). A new AIG embedding the multiplexer tree structures which are intentionally synthesized by Shannon expansion at the AOs, is overlapped with the optimized AIG. The lossless synthesis technique which employs FRAIG (Functionally Reduced AIG) is applied to this approach. The proposed approach and techniques are validated by implementing and applying them to two RISC processor examples, which yielded 13~30% area reduction, and up to 32% delay reduction. The research will be extended to take into account the constraints on the dedicated hardware for carry chains.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.1
• /
• pp.92-102
• /
• 2017

For an automotive surveillance radar system, fast-chirp train based FMCW (Frequency Modulated Continuous Wave) radar is a very effective method, because clutter and moving targets are easily separated in a 2D range-velocity map. However, pedestrians with low echo signals may be masked by strong clutter in actual field. To address this problem, we proposed in the previous work a clutter cancellation and moving target indication algorithm using the coherent phase method. In the present paper, we initially composed the test set-up using a 24 GHz FMCW transceiver and a real-time data logging board in order to verify this algorithm. Next, we created two indoor test environments consisting of moving human and stationary targets. It was found that pedestrians and strong clutter could be effectively separated when the proposed method is used. We also designed and implemented these algorithms in FPGA (Field Programmable Gate Array) in order to analyze the hardware and time complexities. The results demonstrated that the complexity overhead was nearly zero compared to when the typical method was used.