• 대한기계학회논문집A
• /
• 제25권4호
• /
• pp.564-573
• /
• 2001

The mechanical properties of short carbon/glass fiber reinforced polypropylene are experimentally measured as functions of fiber content and nozzle diameter. Also, these properties are compared with the survival rate of reinforced fibers and fiber volume fraction using image analysis after pyrolytic decomposition. The survival rate of fiber aspect ratio as well as fiber volume fraction is influenced by injection processing condition, the used materials and mold conditions such as diameter of nozzle, etc. In this study, the survival rate of fiber aspect ratio is investigated by nozzle size variations in injection/mold sides. It is found that the survival rate of glass fiber is higher that the survival rate of glass fiber is higher than that of carbon fiber. Both tensile modulus and strength of short-fiber reinforced polypropylene are improved s the fiber volume fraction and nozzle diameter are increased.

• 한국재료학회지
• /
• 제34권7호
• /
• pp.355-362
• /
• 2024

AR (alkali resistant)-glass fibers were developed to provide better alkali resistance, but there is currently no research on AR-glass fiber manufacturing. In this study, we fabricated glass fiber from AR-glass using a continuous spinning process with 40 wt% refused coal ore. To confirm the melting properties of the marble glass, raw material was put into a (platinum) Pt crucible and melted at temperatures up to 1,650 ℃ for 2 h and then annealed. To confirm the transparent clear marble glass, visible transmittance was measured and the fiber spinning condition was investigated by high temperature viscosity measurement. A change in diameter was observed according to winding speed in the range of 100 to 700 rpm. We also checked the change in diameter as a function of fiberizing temperature in the range of 1,240 to 1,340 ℃. As winding speed increased at constant temperature, fiber diameter tended to decrease. However, at fiberizing temperature at constant winding speed, fiber diameter tended to increase. The properties of the prepared spinning fibers were confirmed by optical microscope, tensile strength, modulus and alkali-resistance tests.

• 한국광학회지
• /
• 제32권2호
• /
• pp.49-54
• /
• 2021

본 논문에서는 고출력 광섬유 레이저의 핵심 부품인 대구경 광섬유 엔드캡을 제작하는 장비를 설계 및 제작하였으며, 제작장비를 이용하여 대구경 광섬유 엔드캡을 제작하였다. 대구경 광섬유 엔드캡 제작장비는 레이저 광을 조사하여 접속 열원으로 사용하기 위한 CO2 레이저 광원부, 대구경 광섬유와 엔드캡의 위치를 이송하기 위한 정밀 스테이지 조립체, 스테이지 조립체와 연동되어 융착 시 정렬에 사용되는 비전 시스템으로 구성되어 있다. 레이저 광원의 출력은 스테이지 조립체와 연동되어 출력을 제어하며, 비전 시스템으로 대구경 편광유지 광섬유의 편광축을 정렬할 수 있도록 제작되었다. 자체 제작한 장비를 이용하여 클래드 직경이 400 ㎛인 대구경 편광유지 광섬유와 10(W)×5(D)×2(H) ㎣의 엔드캡을 레이저 융착하여 대구경 광섬유 엔드캡을 제작하였다. 제작된 대구경 광섬유 엔드캡의 신호광 삽입손실, 소광률 및 빔품질(M2)은 각각 0.6%, 16.7 dB, M2x=1.21, M2y=1.22로 측정되었다.

• 한국환경보건학회지
• /
• 제26권4호
• /
• pp.21-28
• /
• 2000

Various man-made mineral fibers(MMMF) including refractory ceramic fiber(RCF) have been used widely in industries as insulation materials. The effect of fibrous dust on human health depends on fiber size, concentration (exposure level), and durability in biological system. Therefore, these parameters should be determined to evaluate accurately the potential risk of fibers on human health. The purpose of this study was to characterize the size of airborne fiber and the workers＇ exposure to airborne fibers in refractory ceramic fiber manufacturing and processing factories. Airborne fibers were collected on 25-mm mixed cellulose ester membrane filters at personal breathing zones, and analyzed by A and B counting rules of the National Institute for Occupational Safety and Health(NIOSH) Method # 7400. The average ratios of the fiber density by B rule to the fiber density by A rule was 0.84. This result indicates that the proportion of respirable fibers (<3 ${\mu}{\textrm}{m}$ diameter) in air samples was high. The average diameter and length of airborne fibers were 1.05${\mu}{\textrm}{m}$ and 35${\mu}{\textrm}{m}$, respectively. The average fiber concentrations (GM) of all personal samples was 0.26f/cc, and the average concentration was highest at blanket cutting and packing processes. The fifty seven percent of personal air samples was exceeded the proposed American Conference of Governmental Industrial Hygienists(ACGIH) Threshold Limit Value(TLV), i.e. 0.2 f/cc. It was concluded that the RCF industrial workers had the higher potential health risk due to small fiber diameter, long fiber length, and high exposure level to the airborne fibers.

• Asian-Australasian Journal of Animal Sciences
• /
• 제15권3호
• /
• pp.401-405
• /
• 2002

An experiment was conducted to determine the effects of caponization on the growth performance, breast and thigh muscles physical properties and fiber diameter of the Pectoralis major and Gastrocnemius pars externa in Taiwan country chicken cockerels. Caponized birds were surgically altered at 10 weeks of age. Birds were fed grower and finisher diets ad libitum during an eighteen-week experimental period. The results indicated that the live weight and feed intake in the capons were significantly (p<0.05) higher and the shank length was significantly (p<0.05) longer than in intact birds. There were no significant (p>0.05) differences in feed conversion and mortality between two treatments at 28 weeks of age. Compared with intact birds, the capons had greater (p<0.05) tenderness in the breast and thigh muscles. Cohesion of the breast muscle in the capons was significantly (p<0.05) better than in the intact birds, but the thigh muscles were not significantly (p>0.05) affected. No treatment differences (p>0.05) were associated with cooking loss, muscle chewiness, and elasticity. The capons had a significantly (p<0.05) smaller fiber diameter in the Pectoralis major, but were not significantly (p>0.05) different in the fiber diameter of the Gastrocnemius pars externa. It is concluded that castration did not depress growth compared with the intact birds, but did improve muscle tenderness. This difference was most pronounced in the thigh muscles.

• 한국세라믹학회지
• /
• 제17권2호
• /
• pp.69-74
• /
• 1980

This study deals with the wire content, wire diameter, aspect ratio , it's arrangement of steel, wire fiber and the sorts of castable which affected the character of steel wire fiber reinformced refractory castable. Two kinds of alumina based refractory castables, one is for 1650℃ and the other is for 1800℃, and stainless steel which is SUS 304 type 0.25, 0.34 , 0.37 and 0.50m/min diameter were used respectively. Aspect ratio was adjusted to 50, 75, 100 and steel fiber content was also adjusted to 1-4wt% each. The results of the experiment were as follows : 1. At firing temperature around 1,000℃, MOR is increased with increasing wire content and aspect ratio with decreasing firing temperature, which depends on the Romualdi's Fiber Spacing Theory. But for calculation of the fiber spacing, Swamy equation is more a aplicable to the extensive fiber mixing conditions. However, the condition differs from the above at firing temperature around 1,350℃ ,because of the degradation of wire and the progress of sintering of castable. 2. Linear change is getting larger corresponding to the increase of wire content, and the spaling resistivity is increasing corresponding to the increase of wire content and to aspect ratio, and with decreasing wire diameter. 3. Firing shrinkage under load is getting greater as higher wire content, and the shrinkage of the test pieces which fiber is vertically oriented is getting greater than the test pieces which fiber is randomly oriented.

• Fibers and Polymers
• /
• 제6권3호
• /
• pp.181-185
• /
• 2005

Silk fibroin (SF) nanofibers were prepared by electrospinning and their application as an enzyme immobilization support was attempted. By varying the concentration of SF dope solution the diameter of SF nanofiber was controlled. The SF nanofiber web had high capacity of enzyme loading, which reached to $5.6\;wt\%$. The activity of immobilized a-chymotrypsin (CT) on SF nanofiber was 8 times higher than that on silk fiber and it increased as the fiber diameter decreased. Sample SF8 (ca. 205 nm fiber diameter) has excellent stability at $25^{\circ}C$ by retaining more than $90\%$ of initial activity after 24 hours, while sample SF11 (ca. 320 nm fiber diameter) shows higher stability in ethanol, retaining more than $45\%$ of initial activity. The formation of multipoint attachment between enzyme and support might increase the stability of enzyme. From these results, it is expected that the electrospun SF nanofibers can be used as an excellent support for enzyme immobilization.

• Fibers and Polymers
• /
• 제3권4호
• /
• pp.129-133
• /
• 2002

It is well known residual gum exists in degummed or rotted hemp fibers. Gum removal results in improvement in fiber fineness and the properties of the resultant hemp yams. However, it is not known what correlation if any exists between the residual gum content in retted hemp fibers and the fiber fineness, described in terms of fiber width in this paper. This study examined the mean width and coefficient of variation (CV) of fiber width of seventeen chemically rotted hemp samples with reference to residual gum content. The mean and CV of fiber width were obtained from an Optical fiber diameter analyser (OFDA 100). The linear regression analysis results show that the mean fiber width is directly proportional to the residual gum content. A slightly weaker linear correlation also exists between the coefficient of variation of fiber width and the residual gum content. The strong linear co-relation between the mean of fiber width and the residual gum content is a significant outcome, since testing for fiber width using the OFDA is a much simpler and quicker process than testing the residual gum content. Scanning Electron Microscopy (SEM) reinforces the OFDA findings. SEM micrographs show a flat ribbon like fiber cross-section hence the term \"fiber width\" is used instead of fiber diameter. Spectral differences in the untreated dry decorticated skin samples and chemically treated and subsequently carded samples indicate delignification. The peaks at $1370cm^{-1}$, $1325cm^{-1}$, $1733cm^{-1}$, and $1600cm^{-1}$ attributed to lignin in the untreated samples are missing from the spectra of the treated samples. The spectra of the treated samples are more amine-dominated with some of the OH character lost.cter lost.

• 한국가시화정보학회지
• /
• 제10권2호
• /
• pp.14-19
• /
• 2012

An optical fiber probe system for measuring the local void fraction in the air-water two-phase flow was developed with a 1550 nm light source. Air was injected through a nozzle placed in the center of the bottom wall of a water-filled cylindrical tank. The optical fiber probe having a diameter of $125{\mu}m$ was sufficiently thin to resolve the air-water interface of the bubbly flows. To verify the performance of the optical fiber probe, the synchronized high speed visualization study using a high speed camera was carried out. Comparison between the optical signals and the instantaneous bubble diffraction images confirms that the optical fiber probe is very accurate to measure the void fraction in two-phase flows. The estimated bubble diameter and the rising velocity by the optical fiber probe have 1% and 5% of accuracy, respectively.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.743-749
• /
• 1999

Recently new rehabilitation techniques have been proposed with advanced composite materials like carbon fiber, aramid, glass fiber sheet and so forth. The purpose of this paper is to investigate the mechanical characteristics of reinforced concrete columns confined with carbon fiber sheet and evaluate the degree of their strengthening effect. For the test, the specimen size of column is 15cm$\times$15cm$\times$90cm reinforced with 4 number of main bars of 10 mm diameter, tied bars of 6 mm diameter and slenderness ratio 20. Columns were wrapped with carbon fiber sheet along the column length. It is necessary to make some assumption regarding the confinement of carbon fiber sheet to apply to reinforced concrete columns under concentric loads. The strength gain effect of columns confined with carbon fiber sheet could be predicted using the proposed equation.