• Current Research on Agriculture and Life Sciences
• /
• v.27
• /
• pp.35-41
• /
• 2009

In this study, waste natural fibers and natural adhesions were used to prepare an environmental biodegradable nonwoven type mulching material. Especially, the nonwoven mulching with higher content of cotton shows a improved biodegradation. Also, the physical properties of nonwoven mulching with different ratios of cotton/rayon were studied. It was found that the degree of biodegradation was controlled by the type of nonwoven materials and adhesions.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.275-276
• /
• 2018

Ultra high performance concrete(UHPC) represents high early age autogenous shrinkage strain due to its low water-to-binder ratio(W/B) and high fineness admixture usage. It has been reported that fiber can control restrained tensile stress and crack. The purpose of the present study is, therefore, to investigate the autogenous shrinkage as well as mechanical properties including compressive strength, flexural strength and modulus of elasticity on the UHPC with fiber type and pre-mix of binder.

• Journal of the Optical Society of Korea
• /
• v.19 no.2
• /
• pp.199-205
• /
• 2015

We investigated the effects of the thickness and doping concentration in p- and n-type poly-Si layers on the performance of a solar cell based on a carbon fiber in order to improve the energy conversion efficiency of the cell. The short-circuit current density and open-circuit voltage of the carbon fiber-based solar cell were significantly influenced by the thickness and doping concentration in the p- and n-type poly-Si layers. The solar cell efficiency was successfully enhanced to ~10.5%.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.12
• /
• pp.1270-1277
• /
• 2008

For designing intensity modulation type optical microphone, the irradiance distribution which can be applied to inclined-cut geometrical configuration is suggested. The model is important in analysis of response characteristics for intensity modulation type optical microphone. To overcome low sensitivity problem in intensity modulation type optical microphone, inclined-cut optical fiber is considered here. Based on optical geometry, the inclined-cut optical fiber sensor is designed and fabricated. The experiments are carried out to evaluate sensor performance.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.4
• /
• pp.17-26
• /
• 2018

This study systematically examines the changes in the compressive and tensile strength of soil cement reinforced by natural hair fiber, which is regularly produced from human. Extensive experimental tests of various test specimens have been carried out in a laboratory. Several factors are considered, including the soil type, amount of cement, amount of fiber, fiber length, loading type, and curing age. The test results indicate that both the compressive and tensile strengths are significantly affected by the fiber, either increasing or decreasing depending on the conditions. The increase in tensile strength is significant in the sand-based soil cement due to the tensile resistance of the fiber which is interlocked with the surrounding soil or cement particles. The natural fiber provides a larger strain to failure due to its extensibility, which allows greater deformation. Based on the test results, natural hair fibers can be an effective and environmentally friendly way to improve soil ground subjected to tensile loading, such as an embankment slope, road subgrade, or landfill, thus reducing the cost for cement and waste treatment. The study results provide a useful information of better understanding the mechanical behavior of natural hair fiber in soil cement and the practical use of waste materials in civil engineering. The findings can be practically applied for improving earth structures under tensile loading.

• Journal of Environmental Science International
• /
• v.19 no.4
• /
• pp.509-516
• /
• 2010

This study was investigated the characteristics of indoor air concentration of fiber particles in 30 public facilities and 245 schools by PCM (phase contrast microscopy). Also SEM/EDX (scanning electron microscope / energy dispersive using X-ray analysis) was used to obtain physicochemical information of asbestos fiber and to classify asbestos and non-asbestos of fiber particles. The airborne concentrations of fiber particles were $0.0009\pm0.0009$ counts/mL in public facilities and $0.0012\pm0.0006$ counts/mL in schools by PCM. All the samples were satisfied with the IAQ (indoor air quality) level of 0.01 counts/mL. In classification of 4 type shapes, over 80% of the fiber particles were identified as single fiber type. And this study analysed airborne fiber particles in 4 sites for identifying asbestos of by SEM/EDX. The asbestos fibers in most samples could not be found.

• Carbon letters
• /
• v.3 no.3
• /
• pp.127-132
• /
• 2002

Unidirectional polymer composites were prepared using high-strength carbon fibers as reinforcement and phenolic resin as matrix precursor with keeping fiber volume fraction at 30, 40, 50 and 60% respectively. These composites were carbonized at $1000^{\circ}C$ and graphitised at $2600^{\circ}C$ in the inert atmosphere. The carbonized and graphitised composites were characterized for mechanical properties as well as microstructure. Microscopic studies were carried out of the polished surface of carbonized and graphitised composites after etching by chromic acid, to understand the effect of fiber volume fraction on oxidation at fiber-matrix interface. It is found that the flexural strength in polymer composites increases with fiber volume fraction and so does for the carbonised composites. However, the trend was found to be reversed in graphitised composites. In all the carbonized composites anisotropic region has been observed at fiber-matrix interface which transforms into columnar type microstructure upon graphitisation. The extension of strong and weak columnar type microstructure is function of fiber volume fraction. SEM microscopy of the etched surface of the sample reveal that composites containing 40% fiber volume has minimum oxidation at the interface, revealing a strong interfacial bonding.

• Food Science of Animal Resources
• /
• v.37 no.5
• /
• pp.716-725
• /
• 2017

The objective of this study was to determine the relationship between composition of muscle fiber types and meat quality traits of eight major muscles from Hanwoo steers. Longissimus lumborum (LL), psoas major (PM), semimembranosus (SM), semitendinosus (ST), gluteus medius (GM), triceps brachii (TB), rectus abdominis (RA) and superficialis flexor (SF) muscles were obtained from 9 Hanwoo steers and subjected to histochemical analysis. There were significant (p<0.05) differences in fiber number percentage (FNP) and fiber area percentage (FAP) of fiber types among these 8 major muscles. SF had the highest FNP of type I (55.9%), followed by PM (46.4%), TB (45.4%), RA (38.5%), LD (36.8%), GM (36.0%), SM (22.2%), and ST (18.8%). FAP of type IIB ranged from 9.9% in SF to 58.7% in ST. Meat quality traits, including fat content, myoglobin content, collagen content, CIE $L^*$ and $a^*$, drip and cooking loss, sarcomere length and Warner-Bratzler shear force, were all significantly (p<0.05) different among these muscles. Due to such diversities among these 8 muscles, lack of correlations were found between fiber type composition and meat quality traits. These results suggest that correlation for each individual muscle should be used to improve meat quality and profitability of retail beef cuts.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.478-481
• /
• 1995

This paper presents the system demonstrator for an optical fiber sensor system developed as a technological evaluator suitable for generic sensric sensing applications. The new type of fiber-optic sensor employed a diaphragm displacement transforms pressure into optical intensity. Form this sensing technique, we can know the variation of source intensity, the loss of a optical fiber, and the reflectivity of the diaphragm surface. Experimental results are applied to the low-pressure transducer suitable for measuring miniature pressure.

• Journal of Biomedical Engineering Research
• /
• v.37 no.5
• /
• pp.186-194
• /
• 2016

In this study, a co-axial flow induced microfluidic chip to fabricate pure collagen type I microfiber via the control of collagen type I and Na-alginate gelation process. The pure collagen type I microfiber was generated by selective degradation of Ca-alginate from 'Core-Shell' structured hydrogel microfiber. To make 'Core-Shell' structure, collagen type I solution was introduced into core channel and 1.5% Na-alginate solution was injected into side channel in microfluidic chip. To evaluatethe 'Core-Shell' structure, the red and green fluorescence substances were mixed into collagen type I and Na-alginate solution, respectively. The fluorescence substances were uniformly loaded into each fiber, and the different fluorescence images were dependent on their location. By immoblizing EpH4-Ras and C6 cells within collagen type I and Na-alginate solution, we sucessfully demonstrated the co-culture of EpH4-Ras and C6 cells with 'Core-Shell' like hydrogel microfiber for 5 days. Only to produce pure collagen type I hydrogel fiber, tri-sodium citrate solution was used to dissolve the shell-like Ca-alginate hydrogel fiber from 'Core-Shell' structured hydrogel microfiber, which is an excellent advantage when the fiber is employed in three-dimensional scaffold. This novel method could apply various application in tissue engineering and biomedical engineering.