• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.8
• /
• pp.632-639
• /
• 2018

This paper presents a single antenna radar sensor with a Ku-band radar transceiver IC realized by 130 nm CMOS processes. In this radar receiver, sensitivity time control using a DC offset cancellation feedback loop is employed to achieve a constant SNR, irrespective of distance. In addition, the receiver RF block has gain control to adjust high dynamic range. The RF output power is 9 dBm and the full chain gain of the Rx is 82 dB. To reduce the direct-coupled Tx signal to the Rx in a single antenna radar, a stub-tuned hybrid coupler is adopted instead of a bulky circulator. The maximum measured distance between the horn antenna and a metal plate target is 6 m.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.1
• /
• pp.18-25
• /
• 2018

In this paper, we present a low-power implementation of the multi-channel hearing aid system using a general-purpose DSP chip. The system includes an acoustic amplification algorithm based on Wide Dynamic Range Compression (WDRC), an adaptive howling canceller, and a single-channel noise reduction algorithm. To achieve a low-power implementation, each algorithm is re-constructed in forms of integer program, and the integer program is converted to the assembly program using BelaSigna(R) 250 instructions. Through experiments using the implementation system, the performance of each processing algorithm was confirmed in real-time. Also, the clock of the implementation system was measured, and it was confirmed that the entire signal processing blocks can be performed in real time at about 7.02MHz system clock.

• Journal of Communications and Networks
• /
• v.18 no.6
• /
• pp.913-925
• /
• 2016

In-band wireless full-duplex is a promising technology that enables a wireless node to transmit and receive at the same time on the same frequency band. Due to the complexity of self-interference cancellation techniques, only base stations (BSs) are expected to be full-duplex capable while user terminals remain as legacy half-duplex nodes in the near future. In this case, two different nodes share a single subchannel, one for uplink and the other for downlink, which causes inter-node interference between them. In this paper, we investigate the joint problem of subchannel assignment and power allocation in a single-cell full-duplex orthogonal frequency division multiple access (OFDMA) network considering the inter-node interference. Specifically, we consider two different scenarios: i) The BS knows full channel state information (CSI), and ii) the BS obtains limited CSI through channel feedbacks from nodes. In the full CSI scenario, we design sequential resource allocation algorithms which assign subchannels first to uplink nodes and then to downlink nodes or vice versa. In the limited CSI scenario, we identify the overhead for channel measurement and feedback in full-duplex networks. Then we propose a novel resource allocation scheme where downlink nodes estimate inter-node interference with low complexity. Through simulation, we evaluate our approaches for full and limited CSIs under various scenarios and identify full-duplex gains in various practical scenarios.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.177-182
• /
• 2007

This paper presents the InGaP/GaAs HBT differential LC VCO with low phase noise performance for adaptive feedback interference cancellation system(AF-lCS). The VCO is verified with enhanced tank structure including filtering technique. The output tuning range for proposed VCO using asymmetric inductor and symmetric capacitors withlow pass filtering technique is 207 MHz. The output powers are -6.68 including balun and cable loss. The phase noise of this VCO at 10 kHz, 100 kHz and 1 MHz are -102.02 dBc/Hz, -112.04 dBc/Hz and -130.40 dBc/Hz. The VCO is designed within total size of $0.9{\times}0.9mm^2$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.7
• /
• pp.1321-1327
• /
• 2009

In this paper, as the mobile communication service is widely used and the demand for wireless repeaters is rapidly increasing because of the easiness of extending service areas. But a wireless repeater has a problem the oscillation due to feedback signal. We proposed a new hybrid interference canceller using the adaptive filter with CMA(Constant Modulus Algorithm)-Grouped LMS(Least Mean Square) algorithm in the adaptive interference canceller. The proposed interference canceller has better channel adaptive performance and a lower MSE(Mean Square Error) than conventional structure because it uses the cancellation method of Grouped LMS algorithm. The proposed detector uses the LMS algorithms with two different step size to reduce mean square error and to obtain fast convergence. This structure reduces the number of iterations for the same MSE performance and hardware complexity compared to conventional nonlinear interference canceller.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2395-2402
• /
• 2013

An active-RC channel selection filter (CSF) with the bandwidth of 40MHz and the improved linearity is proposed in this paper. The proposed CSF is the fifth butterworth filter which consists of a first order low pass filter, two second order low pass filters of a biquad architecture, and DC feedback circuit for cancellation of DC offset. To improve the linearity of the CSF, a body node of a MOSFET for a switch is connected to its source node. The bandwidth of the designed CSF is selected to be 10MHz, 20MHz and 40MHz and its voltage gain is controlled by 6 dB from 0 dB to 24 dB. The proposed CSF is designed by using 40nm 1-poly 8-metal CMOS process with a 1.2V. When the designed CSF operates at the bandwidth of 40 MHz and voltage gain of 0 dB, the simulation results of OIP3, in-band ripple, and IRN are 31.33dBm, 1.046dB, and 39.81nV/sqrt(Hz), respectively. The power consumption and layout area are $450{\times}210{\mu}m^2$ and 6.71mW.

• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.433-438
• /
• 1999

This paper describes Active Noise Cancellation/Control(ANC) method that removes the information of the unnecessary noise and doesn't remove the informations of the necessary noise(warning sound, operating sound etc.) for the induced noise of the mechanical system. In this paper, the noise source Is axial fan, and the Feedback Active Noise control method that can effectively control BPF generated from the axial fan is used, and the Filtered-X LMS algorithm for adaptive algorithms is used. The experiments are executed for two case(propagating noise in the duct, emission noise for exterior free field). The part to be removed is BPF noise, and the band-pass filter not to effect to the other frequencies is used. Also, to investigate the effect of the noise reduction for human, we are compared with the results that are controlled for using Loudness before and after. As a results, we are certified that the BPF is decreased only and frequencies outside of BPF are not affected, and we acquire the reduction effects of 6.7 dB Loudness Level, then the frequency to be removed is controlled. Therefore, we can be certified that sound pressure as well as loudness can be effectively decreased for human sound quality

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.10
• /
• pp.1096-1103
• /
• 2008

This paper proposes an individual order predistortion linearizer using intermodulation distortion(IMD) generator for cancellation the third and the fifth IMD of power amplifier. The IMD generator for controlling the third and the fifth IMD consist of common Emitter amplifier and Schottky diode. These signals are generated by series feedback of Schottky diode to obtain the inverse AM/AM and AM/PM characteristics of power amplifier. The individual order predistorters are consisted of individual IMD generator, power splitter and combiner. The test results show that the third and the fifth IMD can be improved by a maximum 13.5 dB and 0.9 dB in case of CW 2-tone signals. Also, the Adjacent Channel Leakage Ratio(ACLR) can be improved 2.3 dB, 2.5 dB at ${\pm}0.885$ MHz, ${\pm}1.23$ MHz offset frequency for CD-MA IS-95 2FA signals.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.8
• /
• pp.22-26
• /
• 2012

This paper introduces a 2.5-Gb/s optical receiver implemented in a standard 1P4M 0.18um CMOS technology for the applications of active optical HDMI cables. The optical receiver consists of a differential transimpedance amplifier(TIA), a five-stage differential limiting amplifier(LA), and an output buffer. The TIA exploits the inverter input configuration with a resistive feedback for low noise and power consumption. It is cascaded by an additional differential amplifier and a DC-balanced buffer to facilitate the following LA design. The LA consists of five gain cells, an output buffer, and an offset cancellation circuit. The proposed optical receiver demonstrates $91dB{\Omega}$ transimpedance gain, 1.55 GHz bandwidth even with the large photodiode capacitance of 320 fF, 16 pA/sqrt(Hz) average noise current spectral density within the bandwidth (corresponding to the optical sensitivity of -21.6 dBm for $10^{-12}$ BER), and 40 mW power dissipation from a single 1.8-V supply. Test chips occupy the area of $1.35{\times}2.46mm^2$ including pads. The optically measured eye-diagrams confirms wide and clear eye-openings for 2.5-Gb/s operations.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.2
• /
• pp.110-116
• /
• 2013

The amplification rate of a RF repeater is limited by the feedbacked signals from the same repeater. And an ICS (Interference Cancellation System) repeater has been developed to remove the feedbacked signals. The ICS repeater estimates the amplitudes and the phases of the feedbacked signals and removes the estimated feedback signals from the received input signal of the repeater. However, it requires lots of hardware complexity and this leads to the increase the cost of the repeater. Moreover, the ICS repeater can not solve the pilot pollution problems. To solve these problems, we have studied the implementation and adaptation of smart antenna system for RF repeaters. We have designed a smart antenna system with a switching beam structure in order to reduce the hardware and computational complexity. After analyzing the proposed smart antenna system, we found out that the amplification rate of the proposed repeater increases 23dB compare to the amplification rate of ICS repeater and the output SINR increases 6dB compare to the ICS repeater.