• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.1
• /
• pp.85-91
• /
• 2003

The experimental study for turning circular free fanned surface with TiN coated insert tool was conducted for different cutting conditions such as cutting speed, feed rate and depth-of-cut. For the fluctuation of 1.0mm depth-of-cut, the characteristics for machined surface and tool wear were less influenced by the feed rate and cutting speed than those of higher depth of cut. The higher surface roughness and surface precision were obtained in lower cutting speed. For the fluctuation of 1.5mm depth-of-cut, the higher surface roughness was obtained for the case of the lower feed rate of 0.05-10mm/rev and the higher cutting speed of 80m/min. For the fluctuation of 2.0mm depth-of-cut, the surface roughness and surface precision were too worse to machine the specimen And the flank wear on the tool was increased rapidly rather than the crater wear.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.5
• /
• pp.1176-1181
• /
• 1995

Microdrilling is one of the most difficult operations because of the poor chip discharge and the weakness of tool. This study is concerned about the development of a microdrilling monitoring system that is useful for minimizing the tool breakage and enhancing the machinability in the air spindle based microdrilling. The system is composed of a drilling state detection unit and an adaptive step-feed control unit that controls the micro-stepping motor driven spindle axis. Drilling states such as overload, tood breakage are recognized by the change of the air spindle speed which is measured via the reflective photo sensor. Based on the monitoring results, the adaptive step-feed control algorithm adjusts the step increment to keep the decrease of spindle speed within a specified range. The results of evaluation tests have shown that the developed system is very effective to prevent the breakage of microdrill and improves the productivity in comparison with the conventional microdrilling.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.11-18
• /
• 2002

The STD11 and KP4 are important steels and applied to the manufacturing of the die and mold. The purpose of this study is to investigate the machinability of tool steels of STD11(HRC60) and KP4(HRC32) when machining them by using ball end milling tools coated with TiAlN. Cutting forces by using a Kistler piezo-cell type tool dynamometer, surface roughness and tool wear by using tool microscope are used in the tests. The results from the cutting tests of KP4 specimens show that 85m/min. of cutting speed and 0.32mm/rev. of feed per revolution are optimum conditions for the higher productivity and 0.26mm/rev. with the same cutting speed are optimum conditions for better surface finishing. The results from machining STD11 workpiece at 30m/min. of cutting speed and 0.17m/rev. of feed per revolution show recommended for the higher productivity. The KP4 shows relatively smaller cutting forces than STD11 and STD11 shows the better surface finish than KP4.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.147-148
• /
• 2012

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.413-417
• /
• 2001

High speed linear motor feed system has been simulated using neural network technique. Due to the limited resources, control gain tuning has been the most troublesome part in controller design. Regardless of the system structure, conventional control gain could be adjusted minimizing the resulting error using the proposed method. Slight performance deterioration was observed at the small value of training epoch.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.450-453
• /
• 2001

Linear motor is characterized by its high velocity, high acceleration and good positioning accuracy. In recent years, linear motor is often used as a fast feed mechanism for high-speed machine tools. For the effective application of linear motors to machine tools, many demands on machine conceptions must be fulfilled. In this paper, some important construction concepts such as bending deformation of machine table, frictional force on the linear guidance and thermal behavior of linear motors are presented.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.7
• /
• pp.104-118
• /
• 1998

In this paper, the motion of ballscrew and shape of workpiece are the main objective variables varying with load conditions. To verify feed mechanism in NC lathe, the monitoring system is designed and cutting condition variables are spindle speed depth of cut and feed. During machining, rotation number of ballscrew motion of ballscrew in direction to gravity center and cutting force are measured. After machining, the roughness of workpiece is measured.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.5
• /
• pp.457-462
• /
• 2014

Given their low cost, single rolling piston compressors (SRPC) are utilized in low-power room air-conditioning systems. The SRPC cycle is composed of one compression and discharge process per mechanical rotation. The load torque is high during the compression process of the refrigerants and low during the discharge process of the refrigerants. This load torque variation induces a speed ripple and severe vibration, which cause fatigue failures in the pipes and compressor parts, particularly under low-speed conditions. To reduce the vibration, the compressor usually operates at a high-speed range, where the rotor and piston inertia reduce the vibration. At a low speed, a predefined feed-forward load torque compensator is used to minimize the speed ripple and vibration. However, given that the load torque varies with temperature, pressure, and speed, a predefined load torque table based on one operating condition is not appropriate. This study proposes an online load torque compensator for SRPC. The proposed method utilizes the speed ripple as a load torque ripple factor. The speed ripple is transformed into a frequency domain and compensates each frequency harmonic term in an independent feed-forward manner. Experimental results are presented to verify the proposed method.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1028-1032
• /
• 2004

In order to prevent machine tool feed slide system from transient vibrations during operations, machine tool designers usually adopt some typical design solutions; box-in-box typed feed slides, optimizing moving body for minimum weight and dynamic compliance, and so on. Despite all efforts for optimizing design, a feed drive system may experience severe transient vibrations during high-speed operation if its feed rate control is unsuitable. A rough feed rate curve having discontinuity in its acceleration profile causes a serious vibration problem in the feed slides system. This paper presents a feed rate optimization of a ball screw driven machine tool feed slide system for its minimum vibration. Firstly, a ball screw feed drive system was mathematically modeled as a 6-degree-of-freedom lumped parameter system. Next, a feed rate optimization of the system was carried out for minimum vibrations. The main idea of the feed rate optimization is to find out the most appropriate smooth acceleration profile with jerk continuity. A genetic algorithm was used in this feed rate optimization

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.629-634
• /
• 2000

Generally, the accuracy of motion control systems is strongly influenced by both the mechanical characteristics and servo characteristics of feed drive systems. In the fed drive systems of machine tools that consist of mechanical parts and electrical parts, a torsional vibration is often generated because of its elastic elements in torque transmission. Especially, a torsional vibration caused by the elasticity of mechanical elements might deteriorate the quick movement of system and lead to shorten the life time of the mechanical transmission elements. So it is necessary to analyze the electromechanical system mathematically to optimize the dynamic characteristics of the feed drive system. In this paper, based on the simplifies feed drive system model, radius errors due to position gain mismatch and servo response characteristic have been developed and an optimal criterion for tuning the gain of speed controller is discussed. The proportional and integral parameter gain of the feed drive controller are optimal design variables for the gain tuning of PI speed controller. Through the optimization problem formulation, both proportional and integral parameter are optimally tuned so as to compensate the radius errors by using the genetic algorithm. As a result, higher performance on circular profile tests has been achieved than the one with standard parameters.