• Journal of Power Electronics
• /
• 제18권3호
• /
• pp.871-878
• /
• 2018

In this paper, the conducted EMI reduction performances of active feed-forward current-sensing current-actuation (CSCA) and voltage-sensing current-actuation (VSCA) filters for a three-phase induction motor drive system are evaluated by experiments. For comparison purposes, the conducted EMI (CM emission, DM emission and total emission) of a three-phase induction motor drive with a conventional CM choke, a conventional CM choke in series with an active VSCA filter, and an active CSCA filter (where the CM choke was modified and used as a sensing current transformer) were compared to the case of a system without any filter inserted. Experimental results show that the active CSCA and VSCA filters can improve the CM reduction performance of the conventional CM choke by about 5 dB especially at low-frequencies. However, for DM comparisons, it shows that there is no different between cases with and without filters inserted.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.641-645
• /
• 1996

Ball screws are used in the feeding system for transmission of driving force. The friction effect between bed and table, which can affect in accuracyin one dimension feeding and describe the dynamic feeding error, could be simplified as a specific model through experiments. The experiments for dynamic feeding errors were performed om tje NC lathe eith a ball screw. The errors in feeding were measured with respect to the variances of feed, spindle speed and motor current for feeding. A rotary encoder and a current sensor were installed with NC lathe.

• 한국정밀공학회지
• /
• 제16권3호통권96호
• /
• pp.38-46
• /
• 1999

Spindle motor current is used to estimate the cutting force indirectly and control the feed rate for the cutting force regulation. The proposed algorithm is implemented to a DSP board based hardware for the industrial application. The software to make POP terminal communicate with the DSP board and POP server is coded under Windows 95 environment. Experiments under varying cutting conditions show that the DSP board recognizes the information of installed cutting tool and cutting conditions delivered from the POP server to use them for the proper control of the feed rate. The cutting force is regulated well during machining of tapered or stepped workpiece and circular shaped workpiece as well.

• 한국수소및신에너지학회논문집
• /
• 제20권3호
• /
• pp.208-215
• /
• 2009

PEMFC stack power output is needed to be around 100 kW to meet the requirements of automotive application and scaling-up the active area of the stack cells will allow a higher power. In the case of scaling-up the active area of cells, it is difficult to obtain uniform in-plane internal conditions such as temperature, relative humidity and stoichiometry of the feed gas. These ununiformity with the location in the cell would affect both the performance and durability of the stack, so it is important to understand phenomena in the cell for improving them. In this study, the current density, electrochemical resistance and performance distribution measurement was performed to understand the ununiformity in a single cell using in-situ method; (1) Current Density Distribution (CDD) Device and (2) Segmented Cell Fixture. The influence of location of feed gas on the performance of a single cell was experimentally measured and discussed by using a segmented single cell which was composed of 8 compartments. The correlation between the location and performance in a single cell was discussed by these two tools and it was extended between the local characterization and the durability in a MEA by comparing the used cell with a fresh one. It was also studied in terms of electrochemistry by Electrochemical Impedance Spectroscopy.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.840-843
• /
• 1996

This paper presents an adaptive cutting force controller for milling process, which can be attached to most commercial CNC machining centers in a practical way. The cutting forces of X,Y and Z axes measured indirectly from the use of currents drawn by AC feed-drive servo motors. A typical model for the feed-drive control system of a horizontal machining center is developed to analyze cutting force measurement from the drive motor. The pulsating milling forces can be measured indirectly within the bandwidth of the current feedback control loop of the feed-drive system. It is shown that indirectly measured cutting force signals can be used in the adaptive controller for cutting force regulation. The robust controller structure is adopted in the whole adaptive control scheme. The conditions under which the whole scheme is globally convergent and stable are presented. The suggested control scheme has been implemented into a commercial machining center, and a series of cutting experiments on end milling and face milling processes are performed. The adaptive controller reveals reliable cutting force regulating capability under various cutting conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• 제9권3호
• /
• pp.250-256
• /
• 1985

With the advant of thryistors having large peak inverse voltages, current-source inverters are becoming very popular to feed induction motors. But it is very difficult to analysis the commutation. Since the actual variation of current during commutation is neither instantaneous nor linear and is effected by many parameters. Minimized bias-time of reverse voltages during commutation is expressed in term of machine parameters, capacitor voltage, load current and so on. The minimized bias-time is computed with y and z and also the commuation mechanism is tested on 2.2 kw induction motor. The computed results are compared with the experimental results, and the results give a good information for designing the commutation mechanism.

• 한국산업융합학회 논문집
• /
• 제18권1호
• /
• pp.1-9
• /
• 2015

This research dealt with a two-degree-of-freedom controller which was used for 2-dimensional force generator based on an linear motor. The gain margin of the controller may be reduced when the time constant is near to the sampling time of a discrete controller. In case of low gain controller, it cannot satisfy the control performance. A two-degree-of-freedom controller based on PI-control was proposed. It can manage performance and stability respectively. It also had a kind of a feed-forward control. This scheme can not only lessen gain of conventional PI controller in order to stability but also obtain high tracking performance.

• Journal of Electrical Engineering and Technology
• /
• 제8권1호
• /
• pp.106-109
• /
• 2013

It is desirable and advantageous to feed parallel propulsion with induction motors by a single voltage source inverter. However, effects of deviation of the wheel diameters on motor current, rotor speed and torque should be also considered for parallel operation. In order to understand the behavior and characteristics, a simple simulation model is developed by using a commercial Matlab Simulink. From the results, it is clear to manage the diameter deviation of the wheels which are connected to traction motors.

• Journal of Welding and Joining
• /
• 제31권1호
• /
• pp.26-32
• /
• 2013

Recently, welding technology of nonferrous metals which were difficult to implement by arc welder has become available through digitalization of arc welding machine. Among them, the welding quality improvement of aluminum welding is very noticeable. These results increase the arc stability by controlling arc current and voltage waveform precisely, and control wire feed speed by synchronizing with arc current which the feed rate of filler wire is controlled by a precise motor control of servomotor and not by a simple constant speed feeding. Not only through the hardware digitalization of arc welding machine but also through advance of software of arc welding, it became possible to implement a certain level of welding quality by a simple operation. These led to CMT welding process implementation which requires low heat input than current arc welding and highly increased the applicability of the aluminum welding.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.135-136
• /
• 2010