• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2008년도 Asian Magnetics Conference
• /
• pp.312.1-312.1
• /
• 2008

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2008년도 Asian Magnetics Conference
• /
• pp.241.2-241.2
• /
• 2008

• 한국재료학회지
• /
• 제16권9호
• /
• pp.557-563
• /
• 2006

The electrolytic reduction of spent oxide fuel involves the liberation of oxygen in a molten LiCl electrolyte, which results in a chemically aggressive environment that is too corrosive for typical structural materials. So, it is essential to choose the optimum material for the process equipment handling molten salt. In this study, corrosion behavior of Inconel 713LC, MA 754, X-750 and 718 in the molten salt $LiCl-Li_2O$ under an oxidizing atmosphere was investigated at $650^{\circ}C$ for $72{\sim}216$ hours. Inconel 713LC alloy showed the highest corrosion resistance among the examined alloys. Corrosion products of Inconel 713LC were $Cr_2O_3,\;NiCr_2O_4$ and NiO, and those of Inconel MA 754 were $Cr_2O_3\;and\;Li_2Ni_8O_{10}$ while $Cr_2O_3,\;NiFe_2O_4\;and\;CrNbO_4$ were produced from Inconel 718. Also, corrosion products of Inconel X-750 were found to be $Cr_2O_3,\;NiFe_2O_4\;and\;(Cr,Nb,Ti)O_2$. Inconel 713LC showed local corrosion behavior and Inconel MA 754, 718, X-750 showed uniform corrosion behavior.

• 한국표면공학회지
• /
• 제50권6호
• /
• pp.516-522
• /
• 2017

We report the growth of carbon nanotubes (CNT) on Invar-42 plates using coal tar pitch (CTP) by chemical vapor deposition (CVD) method. The solid phase CTP is used as an inexpensive carbon source since it produces a bunch of hydrocarbon gases such as $CH_4$ and other $C_xH_v$ by thermal decomposition over $450^{\circ}C$. The Invar-42 is a representative Ni-based ferrous alloy and can be used repetitively as a substrate for CNT growth because Ni and Fe are used as very active catalytic elements. We changed mixing ratio of carrier gases, argon and hydrogen, and temperature of growth region. It was found that the optimum gas ratio and temperature for high quality CNT growth are $Ar:H_2=400:400$ sccm and $1000^{\circ}C$, respectively. In addition, the carbon nanoball (CNB) was also obtained by just changing the mixing ratio to $Ar:H_2=100:600$ sccm. Finally, CTP can be employed as a versatile carbon source to produce various carbon-based nanomaterials, such as CNT and CNB.

• 한국수소및신에너지학회논문집
• /
• 제11권1호
• /
• pp.43-49
• /
• 2000

현재 증기나 온수에 의한 열수송은 배관을 통하여 열손실 및 마찰손실 등이 발생하므로 수송거리는 3 내지 5km가 한계이다. 그러나 대부분의 공단이 도시지역에서 10km 이상 떨어져 있으므로 이들 지역에서 발생되는 폐열을 적절히 활용하기 위해서는 새로운 열수송 시스템이 개발되어야 한다. 수소저장합금은 수소를 흡수 또는 방출하면서 발열반응과 흡열반응을 일으키는 특성을 가지고 있으므로 산업공단지역의 폐열로부터 수소저장합금의 수소를 방출시키고, 이 수소를 인근 도시지역에 파이프라인으로 수송한 후 필요시 또 다른 수소저장합금과 반응시켜 열을 얻을 수 있다. 이 시스템에서는 난방의 목적 외에도 수소의 흡수 방출온도가 낮은 합금을 이용하여 냉열을 얻을 수도 있다. 따라서 수소저장합금은 폐열의 저장이나 열수송의 수단으로 활용할 수 있다. $MmNi_{4.5}Al_{0.5}Zr_{0.003}$, $LaNi_5$, $Zr_{0.9}Ti_{0.1}Cr_{0.6}Fe_{1.4}$, $MmNi_{4.7}Al_{0.1}Fe_{0.1}V_{0.1}$ 합금들이 열수송에 적합한 합금으로 선정되어 그 특성을 검토하였으며, 열수송시스템의 설계 및 제어기술에 대하여 검토하였다.

• 한국재료학회지
• /
• 제15권12호
• /
• pp.773-779
• /
• 2005

Properties of Ni-base superalloys of Nimonic 80A alloy system were investigated by the observation of microstructures, precipitates ana hardness as a function of the chemical compositions ana the paths of heat treatment. The higher hardness values showed, the higher Ti/Al ratio among high compositions of Cr and Co element. The lower (Ti+Al) and Fe contents decreased in the same Ti/Al ratio, the higher hardness values showed. This results are considered that coherent deformation was increased with increasing Ti/Al ratio. Hardness showed higher value when Cr contents was $18 wt\%$ less than $21wt\%Cr$. In $3.15 wt\%$Co alloy, $\gamma'$ phase was very fine as around 50nm and, its volume fraction and hardness showed the highest value by 2step-aging treatment.

• 한국재료학회지
• /
• 제29권3호
• /
• pp.160-166
• /
• 2019

This study investigates the effect of thermo-mechanical treatment on the damping capacity of the Fe-20Mn-12Cr-3Ni-3Si alloy with deformation induced martensite transformation. Dislocation, ${\alpha}^{\prime}$ and ${\varepsilon}-martensite$ are formed, and the grain size is refined by deformation and thermo-mechanical treatment. With an increasing number cycles in the thermo-mechanical treatment, the volume fraction of ${\varepsilon}-martensite$ increases and then decreases, whereas dislocation and ${\alpha}^{\prime}-martensite$ increases, and the grain size is refined. In thermo-mechanical treated specimens with five cycles, more than 10 % of the volume fraction of ${\varepsilon}-martensite$ and less than 3 % of the volume fraction of ${\alpha}^{\prime}-martensite$ are attained. Damping capacity decreases by thermo-mechanical treatment and with an increasing number of cycles of thermo-mechanical treatment, and this result shows an opposite tendency for general metal with deformation induced martensite transformation. The damping capacity of the thermo-mechanical treated damping alloy with deformation induced martensite transformation greatly affect the formation of dislocation, grain refining and ${\alpha}^{\prime}-martensite$ and then ${\varepsilon}-martensite$ formation by thermo-mechanical treatment.

• 분석과학
• /
• 제17권5호
• /
• pp.416-422
• /
• 2004

시간분해 레이저 유도 파열 분광분석 (TRELIBS) 시스템을 구성하여 원자력발전소 계통재질의 성분을 정성 분석하는 데 응용하였다. 본 연구에서는 탄소강 (A106 Gr. B, A336 P11, A335 P22), 스텐인레스강 (type 304, type 316) 및 인코넬 계열 합금(인코넬 600, 인코넬 690, 인코넬 800) 시료를 사용하였다. 탄소강의 종류는 485~575 nm 파장영역에서 나타난 Cr/Fe과 Mo/Fe의 TRELIBS 피크 비에 의해서 서로 구분 가능하였다. type 304와 type 316 스텐인레스강은 485~575 nm 파장영역에서 나타나는 Mo의 TRELIBS 피크 존재 여부에 의해서 쉽게 구분 가능하였다: type 304는 어떤 Mo의 피크도 나타내지 않지만, type 316은 Mo의 피크를 보여준다. 인코넬 계열 합금강 종류는 420~510 nm 파장영역에서 나타난 Cr/Fe과 Ni/Fe의 TRELIBS 피크비에 의해서 서로 구분 가능하였다. TRELIBS는 시료의 전처리 없이 빠르고 쉽게 합금을 분석할 수 있는 효과적인 분석 기술임이 입증되었다.

• 자원리싸이클링
• /
• 제6권4호
• /
• pp.3-10
• /
• 1997

Electric are furnace dust (EAF dust) generated in steel production based on scrap melting is contained Zn and Fe about 25 and 30 percent by weight, respectively. From a metallurgical point of view, the dust could be regarded as a raw material for Zn and Fe source. To recover the Zn in the metal from EAF dust, many system are proposed such as Arc Plasma Furmace and Pb splasher method. In this study, to recover high purity Zn from Pb splasing alloy, Zn distillation is carried out at the temperature of 1123, 1173, 1223, 1273 K, the gas flow rate of 2.5, 5.0, 8.0 Ni/min and the distilling time of 10, 30, 60, 90 minutes. The main results obtained from this study are as follows:(1) The amount of evaporated Zn and its evaporating rate increased with increasing temperature, but purity of Zn decreased with increasing temperature. Optimum temperature range was found out to be between 1173∼1223K. (2) The amount of evaporated Zn and evaporation rate increased with increasing gas flow rate at a given temperature and distillation time. Gas flow rate has more influence over the amount of evaporated Zn and evaporation rate with increasing temperature.

• Corrosion Science and Technology
• /
• 제9권5호
• /
• pp.223-232
• /
• 2010

NiTi alloy has been used for orthodontic wire due to good mechanical properties, such as elastic strength, friction resistance, and high corrosion resistance. Recently, these wire were coated by polymer and ceramic materials for aesthetics. The purpose of this study was to investigate electrochemical characteristics of tooth colored NiTi wire using various instruments. Wires (round type and rectangular type) were used, respectively, for experiment. Polymer coating was carried out for wire. Specimen was investigated with optical microscopy (OM), field emission scanning electron microscopy (FE-SEM) and energy dispersive x-ray spectroscopy (EDS). The corrosion properties of the specimens were examined using potentiodynamic tests (potential range of -1500 ~ 2000 mV) and electrochemical impedance spectroscopy (frequency range of 100 kHz ~ 10 mHz) in a 0.9 % NaCl solution by potentiostat. From the results of polarization behavior, the passive region of non-coated NiTi wire showed largely, whereas, the passive region of curved NiTi wire showed shortly in anodic polarization curve. In the case of coated NiTi wire, pitting and crevice corrosion occurred severely at interface between non-coated and coated region. From the results of EIS, polarization resistance(Rp) value of non-coated round and rectangular NiTi wire at curved part showed $5.10{\times}10^5{\Omega}cm^2$ and $4.43{\times}10^5{\Omega}cm^2$. lower than that of coated NiTi wire. $R_p$ of coated round and rectangular NiTi wire at curved part showed $1.31{\times}10^6{\Omega}cm^2$ and $1.19{\times}10^6{\Omega}cm^2$.