• Journal of Powder Materials
• /
• v.9 no.3
• /
• pp.161-166
• /
• 2002

Processing and properties of $Al_2O_3$ composites with Ni-Fe content of 10 and 15 wt% were investigated. Homogeneous powder mixtures of $Al_2O_3$/Ni-Fe alloy were prepared by the solution-chemistry route using $Al_2O_3$, $Ni(NO_3)_2{\cdot}6H_2O$ and $Fe(NO_3)_3{\cdot}9H_2O$ powders. Microstructural observation of composite powder revealed that Ni-Fe alloy particles with a size of 20nm were homogeneously dispersed on $Al_2O_3$ powder surfaces. Hot-pressed composites showed enhanced fracture toughness and magnetic response. The properties are discussed based on the observed microstructural characteristics.

• Journal of the Korean institute of surface engineering
• /
• v.33 no.4
• /
• pp.281-288
• /
• 2000

To understand the effect of Fe on the oxidation behavior of TiAl alloys, TiAl-(2, 4, 6at% )Fe were oxidized at 800 and 90$0^{\circ}C$ in air. The oxidation resistance of TiAl-Fe alloys increased with increasing an iron content. The scales formed consisted of an outer $TiO_2$ layer, an intermediate $A1_2$$O_3$ layer, and an inner mixed ($TiO_2$+$A1_2$$O_3$) layer, being similar to other common TiAl alloys. But, the scales formed on TiAl-Fe alloys were generally thin compared to those formed on pure TiAl, and contained dissolved iron. Below the oxide scale, an oxygen affected zone was formed. This beneficial effects of Fe on increasing the oxidation resistance and scale adherence of TiAl alloys were attributed to the refinement of oxide grains, increased scale adherence and the enhanced alumina-forming tendency.

• Journal of Soil and Groundwater Environment
• /
• v.13 no.1
• /
• pp.92-100
• /
• 2008

Experimental studies were conducted to identify the active agents for reductive dechlorination of TCE in cement/Fe(II) systems focusing on cement components such as CaO, $Fe_2O_3$, and $Al_2O_3$. A hematite that was used to simulate an $Fe_2O_3$ component in cement was found to have degradation efficiencies (k = 0.641 $day^{-1}$) equivalent to that of cement/Fe(II) systems in the presence of CaO/Fe(II), only when it contained an aluminum impurity$(Al_2O_3)$. When the effect of $Al_2O_3$ content of hematite/CaO/$Al_2O_3$/Fe(II) system was tested, the mole ratio of $Al_2O_3$ to CaO affected the rate of TCE degradation with an optimum ratio around 1 : 10 that resulted in a rate constant of 0.895 $day^{-1}$. In the SEM images of hematite/CaO/$Al_2O_3$/Fe(II) systems, acicular crystals were also found that were also observed in cement/Fe(II) systems. Thus it was suspected that these crystals were reactive reductants and that they might be goethite or ettringite that are known to have acicular structures. An EDS element map analysis revealed that these crystals were not goethite crystals. A subsequent experiment that tested reactivities of compounds formed during the ettringite synthesis showed that ettringite and minerals associated with ettringite formation are not reactive reductants. These observations conclude that a mineral containing CaO and $Al_2O_3$ with a acicular structure could be a major reactive reductant of cement/Fe(II) systems.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.5
• /
• pp.748-754
• /
• 2010

The contents of soil organic matter (SOM) and $Al_o+1/2Fe_o$ in soils are important criteria for the classification of new Andisols in Soil Taxonomy system. There are many soil types in Jeju Island with various soil forming environments. This paper was conducted to estimate the contents of soil organic matter and the content of ammonium oxalate extracted Al and Fe ($Al_o+1/2Fe_o$) using various environmental variables and to make soil property maps using a statistical analyses. The soil samples were collected from 321 locations and analyzed to measure the contents of SOM and $Al_o+1/2Fe_o$. It was analyzed the relationships among them and various environmental variables such as temperature, precipitation, net primary product, radiation, evapotranspiration, altitude, soil forming energy, topographic wetness index, elevation, difference surrounded area, and distances from the shore and the peak. We can exclude multi-collinearity among environmental variables with principal component analysis and reduce all the variables to 3 principal components. The contents of SOM and $Al_o+1/2Fe_o$ were estimated by multiple regression models and maps of them were made using the models.

• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.3
• /
• pp.195-214
• /
• 2020

The Samgwang Au-Ag deposit has been one of the largest deposits in Korea. The deposit consists of eight lens-shaped quartz veins which filled fractures along fault zones in Precambrian metasedimentary rock, which feature suggest that it is an orogenic-type deposit. The Ti-bearing minerals occur in wallrock (titanite, ilmenite and rutile) and laminated quartz vein (rutile). They occur minerals including biotite, muscovite, chlorite, white mica, monazite, zircon, apatite in wallrock and white mica, chlorite, arsenopyrite in laminated quartz vein. Chemical composition of titanite has maximum vaules of 3.94 wt.% (Al₂O₃), 0.49 wt.% (FeO), 0.52 wt.% (Nb₂O₅), 0.46 wt.% (Y₂O₃) and 0.43 wt.% (V₂O₅). Titanite with 0.06~0.14 (Fe/Al ratio) and 0.06~0.15 (X_Al (=Al/Al+Fe³⁺+Ti)) corresponds with metamorphic origin and low-Al variety. Chemical composition of ilmenite has maximum values of 0.07 wt.% (ZrO₂), 0.12 wt.% (HfO₂), 0.26 wt.% (Nb₂O₅), 0.04 wt.% (Sb₂O₅), 0.13 wt.% (Ta₂O₅), 2.62 wt.% (As₂O₅), 0.29 wt.% (V₂O₅), 0.12 wt.% (Al₂O₃) and 1.59 wt.% (ZnO). Chemical composition of rutile in wallrock and laminated quartz vein has maximum values of 0.35 wt.%, 0.65 wt.% (HfO₂), 2.52 wt.%, 0.19 wt.% (WO₃), 1.28 wt.%, 1.71 wt.% (Nb₂O₃), 0.03 wt.%, 0.07 wt.% (Sb₂O₃), 0.28 wt.%, 0.21 wt.% (As₂O₅), 0.68 wt.%, 0.70 wt.% (V₂O₃), 0.48 wt.%, 0.59 wt.% (Cr₂O₃), 0.70 wt.%, 1.90 wt.% (Al₂O₃) and 4.76 wt.%, 3.17 wt.% (FeO), respectively. Rutile in laminated quartz vein is higher contents (HfO₂, Nb₂O₃, As₂O₅, Cr₂O₃, Al₂O₃ and FeO) and lower content (WO₃) than rutile in wallrock. The substitutions of rutile in wallrock and laminated quatz vein are as followed : rutile in wallrock [(Fe³⁺, Al³⁺, Cr³⁺) + Hf⁴⁺ + (W⁵⁺, As⁵⁺, Nb⁵⁺) ⟵⟶ 2Ti⁴⁺ + V⁴⁺, 2Fe²⁺ + (Al³⁺, Cr³⁺) + Hf⁴⁺ + (W⁵⁺, As⁵⁺, Nb⁵⁺) ⟵⟶ 2Ti⁴⁺ + 2V⁴⁺], rutile in laminated quartz vein [(Fe³⁺, Al³⁺) + As⁵⁺ ⟵⟶ Ti⁴⁺ + V⁴⁺, (Fe³⁺, Al³⁺) + As⁵⁺ ⟵⟶ Ti⁴⁺ + Hf⁴⁺, 4(Fe³⁺, Al³⁺) ⟵⟶ Ti⁴⁺ + (W⁵⁺, Nb⁵⁺) + Cr³⁺], respectively. Based on these data, titanite, ilmenite and rutile in wallrock were formed by resolution and reconcentration of cations (W⁵⁺, Nb⁵⁺, As⁵⁺, Hf⁴⁺, V⁴⁺, Cr³⁺, Al³⁺, Fe³⁺, Fe²⁺) in minerals of wallrock during regional metamorphism. And then rutile in laminated quartz vein was formed by reconcentration of cations (Nb⁵⁺, As⁵⁺, Hf⁴⁺, Cr³⁺, Al³⁺, Fe³⁺, Fe²⁺) in alteration minerals (white mica, chlorite) and Ti-bearing minerals reaction between hydrothermal fluid originated during ductile shear and Ti-bearing minerals (titanite, ilmenite and rutile) in wallrock.

• Korean Journal of Materials Research
• /
• v.24 no.8
• /
• pp.393-400
• /
• 2014

NiO catalysts were successfully coated onto FeCrAl metal alloy foam as a catalyst support via a dip-coating method. To demonstrate the optimum amount of NiO catalyst on the FeCrAl metal alloy foam, the molar concentration of the Ni precursor in a coating solution was controlled, with five different amounts of 0.4 M, 0.6 M, 0.8 M, 1.0 M, and 1.2 M for a dip-coating process. The structural, morphological, and chemical bonding properties of the NiO-catalyst-coated FeCrAl metal alloy foam samples were assessed by means of field-emission scanning electron microscopy(FESEM), scanning electron microscopy-energy dispersive spectroscopy(SEM-EDS), X-ray diffraction(XRD), and X-ray photoelectron spectroscopy(XPS). In particular, when the FeCrAl metal alloy foam samples were coated using a coating solution with a 0.8 M Ni precursor, well-dispersed NiO catalysts on the FeCrAl metal alloy foam compared to the other samples were confirmed. Also, the XPS results exhibited the chemical bonding states of the NiO phases and the FeCrAl metal alloy foam. The results showed that a dip-coating method is one of best ways to coat well-dispersed NiO catalysts onto FeCrAl metal alloy foam.

• Journal of the Korean Ceramic Society
• /
• v.39 no.8
• /
• pp.769-774
• /
• 2002

The powder mixture in which Fe-Ni alloy particles of 20 nm were homogeneously dispersed on $Al_2O_3$ particle surfaces was prepared by hydrogen reduction of $Al_2O_3$ and metal oxide powders. $Al_2O_3$/Fe-Ni nanocomposites fabricated by pressureless sintering were only composed of $Al_2O_3$ and ${gamma}$-Fe-Ni phases and achieved over 98% of the theoretical density at the sintering temperature above $1350^{\circ}C$. The highest strength and toughness of the composites were 574 MPa and 3.9 MP$a{\cdot}m1/2$, respectively. These values were about 20% higher than these of monolithic $Al_2O_3$ sintered at the same conditions. Nanocomposites showed ferromagnetic properties and coercive force was increased with decrease of the average particle size of dispersions.

• Korean Journal of Materials Research
• /
• v.25 no.8
• /
• pp.391-397
• /
• 2015

NiO catalysts/$Al_2O_3$/FeCrAl alloy foam for hydrogen production was prepared using atomic layer deposition (ALD) and subsequent dip-coating methods. FeCrAl alloy foam and $Al_2O_3$ inter-layer were used as catalyst supports. To improve the dispersion and stability of NiO catalysts, an $Al_2O_3$ inter-layer was introduced and their thickness was systematically controlled to 0, 20, 50 and 80 nm using an ALD technique. The structural, chemical bonding and morphological properties (including dispersion) of the NiO catalysts/$Al_2O_3$/FeCrAl alloy foam were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, field-emission scanning electron microscopy and scanning electron microscopy-energy dispersive spectroscopy. In particular, to evaluate the stability of the NiO catalysts grown on $Al_2O_3$/FeCrAl alloy foam, chronoamperometry tests were performed and then the ingredient amounts of electrolytes were analyzed via inductively coupled plasma spectrometer. We found that the introduction of $Al_2O_3$ inter-layer improved the dispersion and stability of the NiO catalysts on the supports. Thus, when an $Al_2O_3$ inter-layer with a 80 nm thickness was grown between the FeCrAl alloy foam and the NiO catalysts, it indicated improved dispersion and stability of the NiO catalysts compared to the other samples. The performance improvement can be explained by optimum thickness of $Al_2O_3$ inter-layer resulting from the role of a passivation layer.

• Carbon letters
• /
• v.5 no.2
• /
• pp.81-87
• /
• 2004

The effect of compositions of $Al_2O_3$ in the mixed $Fe/Al_2O_3$ catalysts on the synthetic behaviors of carbon nanotubes (CNTs) by catalytic chemical vapor deposition (CCVD) process was investigated in wide range of the mixture ratios of support materials. CNTs were synthesized with $Fe/Al_2O_3$ catalysis under the condition of 40 min in synthetic time, and 923 K of synthetic temperature using $C_2H_4$ and $H_2$ as synthetic and carrier gas, respectively. The carbon yield with the content of $Al_2O_3$ showed in a parabolic curve and the maximum carbon yield was 40 wt.% of $Al_2O_3$. As the mixture ratio of $Al_2O_3$ increased, decreasing tendency was observed in the diameter of CNTs. Specific surface areas of CNTs were increased with the increase of the mixture ratio of $Al_2O_3$.

• Journal of the Korean Magnetics Society
• /
• v.8 no.4
• /
• pp.198-202
• /
• 1998

We have studied $Al_xFe_{3-x}O_4$ produced by direct composition method using X-ray diffraction and Mssbauer spectroscopy. The cation distribution for $Al_xFe_{3-x}O_4$ was determined by the ratio of sub-spectra absorption area. The charge state of Fe atoms in octahedral site(B-site) is $Fe^{2.5+}$ based on electron hopping, $Fe^{2+}$ ↔ $(Fe^{3+},Al^{3+})$ without dependency of substituted Al amounts.