• Environmental Engineering Research
• /
• v.25 no.3
• /
• pp.335-344
• /
• 2020

This work describes highly efficient recovery and selective leaching of Zn from electric arc furnace dust (EAFD) with different physicochemical properties, induced by acid leaching at ambient conditions. The chemical compositions, mineralogical phases, and particle sizes of the EAFDs were analyzed and compared. The effects of leaching time, liquid/solid ratio, acid type, and acid concentration on the selective leaching of Zn were also studied. The EAFD with high Fe/Zn ratio (> 1, EAFD₃) was richer in ZnFe₂O₄ and exhibited larger particle size than samples with low Fe/Zn ratio (< 1, EAFD_1,2). ANOVA analysis revealed that the Fe/Zn ratios of the EAFDs also have a significant effect on Zn extraction (p < 0.005). Selective leaching of Zn with minimum Fe dissolution was obtained at pH > 4.5, regardless of other parameters or sample properties. The maximum Zn extraction rate obtained by the pH control was over 97% for EAFD₁ and EAFD₂, 76% for EAFD₃, and 80% for EAFD₄. The present results confirm that the Fe/Zn ratio can be used to identify EAFDs that permits facile and high-yield Zn recovery, and pH can be used as a process control factor for selective leaching of Zn regardless of any differences in the properties of the EAFD sample.

• Journal of the Korean Ceramic Society
• /
• v.50 no.3
• /
• pp.231-237
• /
• 2013

Thermodynamic modeling of the $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ complex ferrite system has been adopted as a rational approach to establish routes to better synthesis conditions for pure phase $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ complex ferrite. Quantitative analysis of the different reaction equilibria involved in the precipitation of $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ from aqueous solutions has been used to determine the optimum synthesis conditions. The spinel ferrites, such as magnetite and substitutes for magnetite, with the general formula $MFe_2O_4$, where M= $Fe^{2+}$, $Co^{2+}$, and $Ni^{2+}$ are prepared by coprecipitation of $Fe^{3+}$ and $M^{2+}$ ions with a stoichiometry of $M^{2+}/Fe^{3+}$= 0.5. The average particle size of the as synthesized $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$, measured by transmission electron microscopy (TEM), is 14.2 nm, with a standard deviation of 3.5 nm the size when calculated using X-ray diffraction (XRD) is 16 nm. When $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ ferrite is annealed at elevated temperature, larger grains are formed by the necking and mass transport between the $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ ferrite nanoparticles. Thus, the grain sizes of the $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ gradually increase as heat treatment temperature increases. Based on the results of Thermogravimetric Analysis (TGA) and Differential Scanning Calorimeter (DSC) analysis, it is found that the hydroxyl groups on the surface of the as synthesized ferrite nanoparticles finally decompose to $Ni_{0.5}Zn_{0.4}Cu_{0.1}Fe_2O_4$ crystal with heat treatment. The results of XRD and TEM confirmed the nanoscale dimensions and spinel structure of the samples.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.1
• /
• pp.58-63
• /
• 2006

In this Paper, ZnO films mixed with iron oxide were prepared by an ultrasonic spray pyrolysis method. The chemical composition and structural properties as a function of the Fe atomic ratio in the deposition solution were studied. Zinc acetate and ferrous chloride were used as precursors of Zn and Fe, respectively. Fe atomic ratio to Zn varied from 0.15 to 10.0. Substrate temperature was fixed at $250^{\circ}C$. The crystallographic properties and surface morphologies of the films were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. Electron probe X-ray microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS) were carried out to analyse the chemical composition and state of Zn and Fe atoms.

• Journal of the Korean Ceramic Society
• /
• v.17 no.3
• /
• pp.121-128
• /
• 1980

In order to obtain the fundamental data for the preparation of ferroxplana $Zn_2Y(Ba_2Zn_2Fe_{12}O_{22})$, which is useful for GHz-band communication, the optimum coprecipitation condition of $Zn(NO_3)_2-6FeCl_3$ in $NH_4OH$ solution and the formation process of the hexagonal ferrite were investigated. By the hot-petroleum-drying and calcining the coprecipitated hydroxide mixture $Zn(OH)_2 +Ba(OH)_2+ 6Fe(OH)_3$, the fine and uniform powder was obtained , whose phase composition and microstructure were studied by X.R.D. and electron microscope. In results, it was found that $Zn_2Y$, BaM and $Zn_2W$ were the representative phases in calcined specimens whose activation energies of crystal growth were about 3, 8, 2.5, $5.4{\times}10^4$ J/mole , respectively. The sintered specimens would be appreciated as useful magnetic cores for the high frequency communication.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.24 no.2
• /
• pp.93-104
• /
• 2004

This pot experiment was conducted to investigate the effects of combined micronutrient application($T_1$; control, $T_2$; Fe, $T_3$; Fe+Mn, $T_4$; Fe+Mn+Cu, $T_5$ ; Fe+Mn+Cu+Zn, $T_6$ ; Fe+Mn+Cu+Zn+Mo, T$_{7}$; Fe+Mn+Cu+Zn + Mo + B) on forage performance of pure and mixed cultures of orchardgrass and white clover. The fifth part was concerned with the changes in the total and relative contents, uptake amounts, and mutual ratios. of micronutrients in forages. The results obtained are summarized as follows: 1. The relative contents(total contents of 6 micronutrients = 100%) of Fe and Mn were considerably influenced by the antagonism between Fe and Mn, and also were influenced by the differences in Mn-absorption between orchardgrass and white clover. Compared with pure culture, orchardgrass showed high relative contents of Mn, and low relative contents of Fe and B in mixed culture. White clover, however, tended to be exactly opposed to the above trends. In relative contents, the T$_6$ 6/ resulted generally in decrease of Fe. However the $T_7$ resulted in increase of Mn and B. In addition, the $T_7$ resulted in decrease of Cu and Zn in orchardgrass, and Mo in white clover. 2. In general, there were differences in the tendency between the yield changes and the uptake amounts of micronutrients. General differences have been showed in the uptake amounts and mutual ratios of micronutrients based on the forage species, pure/mixed culture, additional fertilization, and antagonism. The uptake amounts of total micronutrients were generally increased by the treatments with increased combination. In uptake amounts, the $T_7$ resulted in the increase of Mn and B, and decrease of Mo. 3. The mutual ratios of Fe/Mn, Fe/Cu, and Mn/Cu were considerably influenced by the antagonism between Fe and Mn. At the $T_7$ , very low ratio of Fe/Mo affected by the T6 tended to be somewhat improved because of the decrease of Mo content． The poor growth of forages at the $T_6$ was improved by the $T_7$ . This fact was likely to be caused by the adequate B/Mo ratio.

• Journal of the Korean Magnetics Society
• /
• v.18 no.1
• /
• pp.39-42
• /
• 2008

[ $AB_2X_4$ ](A, B=Transition Metal, X=O, S, Se) are cubic spinel normal ferrimagnets, in which M ions occupy the tetrahedral sites and Cr ions occupy the octahedral sites. Recently, they have been investigated for behaviour of B site ions and A-B interaction. Polycrystalline $[Co_{0.9}Zn_{0.1}]_A[Cr_{1.98}{^{57}Fe_{0.02}}]_BO_4$ compound was prepared by wet-chemical process. The ferrimagnetic transition was observed around 90K. $M\"{o}ssbauer$ absorption spectra at 4.2K show that the well-developed two sextets are superposed with small difference in hyperfine fields($H_{hf}$). The hyperfine fields of $CoCr_{1.98}{^{57}Fe_{0.02}}O_4$ and $Co_{0.9}Zn_{0.1}Cr_{1.98}{^{57}Fe_{0.02}}O_4$ were determined to be 488, 478 kOe and 486, 468 kOe, respectively. We notice that the one of the magnetic hyperfine field values changes with Zn ion substitution. These results suggest the incommensurate states and spin-reorientation temperature($T_S=18K$) changes with Zn ions substitution below spin-reorientation temperature($T_S=28K$) of $CoCr_{1.98}{^{57}Fe_{0.02}}O_4$

• Journal of Environmental Health Sciences
• /
• v.16 no.2
• /
• pp.83-87
• /
• 1990

This study was carried out to investigate the pollution of heavy metals in soil of seven stations from the upper spot (Yeungchun Dam) of Kumho River to the downstream(Gangchang Bridge). The results obtained were as follows: 1. The content of heavy metals in soil of Kumho River basin was highest at Gangchang Bridge [expresed in $\mu$g/g : Mn(246.0), Cd(1.90), Fe(551.2), Cu(108.2), Zn(86.4), Cr(80.2), respectively]. Whereas, the content of heavy metals expect for Mn, Cu was lowest at Yeungchun Dam [Cd(0.40), Fe(548.0), Zn(30.7), Cr(6.2), respectively] Also, the content of Cr, Zn was increased when the sampling areas are changed from upstream to downstream except for Hayang Bridge, and Hayang Bridge was the diverging point of the heavy metals content. 2. There were relatively correlated between Mn : FE, Cu, Zn, Cr, Fe : Cu, Zn, Cr(0.40 < $\left$\mid${r}\right$\mid$$ < 0.70), and were high correlated between Cd : Mn, Fe, Cu, Zn, Cu : Zn, Zn : Cr(0.70 < $\left$\mid${r}\right$\mid$$ < 0.90). Particularly, there was higest correlated between Cd : Cr, Cu : Cr(0.90< $\left$\mid${r}\right$\mid$$ < 1.0)

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.106-106
• /
• 2016

강의 산화 및 부식을 방지할 수 있는 표면처리 강판의 수요가 늘어나고 있다. 그 중 용융아연도금 강판은 뛰어난 경제성 및 도금성, 그리고 희생적 방식 특성으로 각광받고 있다. 자동차용 강판의 경우 도금 공정 이후의 표면 상태가 매우 중요하다. 도금 공정의 주된 표면 결함은 강판이 도금욕 내에서 이동 하면서 수반된 도금욕 내의 Zn-Fe-Al dross 입자에 기인한다. 도금공정 중 강판으로부터 용출된 Fe는 도금욕 내의 Zn 와 Al 과 반응하여 밀도가 높은 Bottom dross 나 밀도가 낮은 Top dross를 형성한다. 이에 본 연구에서는 강판으로부터 Fe의 용출속도에 미치는 도금욕 내 초기Fe 농도의 영향을 속도론적으로 평가하였다. 본 연구에서는 'Finger rotating method (FRM)' 방법론을 적용하였으며. 실험을 위해 수직 관상로 내부에 Zn-Al-Fe 시료를 장입한 알루미나 도가니를 위치시킨 후 온도를 $455^{\circ}C$로 설정하고, 지름 20mm의 Iron rod를 회전모터에 연결하여 Zn-Al-Fe 용탕에 침적한 후 회전시켰다. 실험 결과, 초기 Fe 함량과 용탕의 Fe포화 농도의 차이가 적을수록 Fe의 용출 속도는 감소하였으며 Dross 생성량 또한 적었다. 용탕 및 Iron rod 샘플 관찰 결과를 바탕으로 회전하는 Fe 시편으로부터 도금욕으로의 Fe 용출 메커니즘을 고찰하였다. 용출 모델을 토대로 모델링 한 결과, 용탕 내 Fe 농도 변화양상이 모델링 data와 실험 data가 동일한 양상을 보임을 확인 하였다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.1
• /
• pp.167-173
• /
• 1997

The $ZnFe_2O_4$ powder was prepared under glycothermal conditions by precipitation from metal nitrates with aqueous potassium hydroxide. The fine powder was obtained at temperatures as low as 225 to $300^{\circ}C$. The microstructure and phase of the $ZnFe_2O_4$ powder were studied by SEM and XRD. The properties of the powder were studied as a function of various parameters (reaction temperature, reaction time, solid loading, etc). The average particle size of the $ZnFe_2O_4$ increased with increasing reaction temperature. After glycothermal treatment at $270^{\circ}C$ for 8 h, the average particle diameter of the $ZnFe_2O_4$ was about 50 nm.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.20 no.3
• /
• pp.60-70
• /
• 2012

Zn, Cu, Fe, Al contents of sludges produced from sewage treatment plants and night soil treatment plant in Pocheon City, Gyeong-gi Province were investigated. And the accumulated contents of those metals in the earthworm Eisenia fetida were also investigated while 15, 30, 45, 60, 75, 90, 105 grams(dw) of sludges were cumulatively supplied to the earthworms. Zn contents of sludges were 75.1~196.1 mg/kg, Cu contents 3.74~76.1 mg/kg, Fe contents 219.9~857.8 mg/kg, Al contents 198.4~991.7 mg/kg, all of which would not cause acute toxicity to the earthworm, but could cause sublethal effects on earthworm and reduce the density of next generation's population. However, cumulative supplies of sludges didn't increase the bioaccumulation rates of metals in the earthworm body, and BAFs of those metals after 60g of sludge supply were 0.0~0.43, which meant that the accumulated Zn, Cu, Fe, Al contents in the earthworm were lower than those of sludges.