• Nuclear Engineering and Technology
• /
• v.55 no.10
• /
• pp.3648-3658
• /
• 2023

The early localization of a fuel subassembly with a failed (wet rupture) fuel pin is very important in reactors to limit the associated radiological and operational consequences. This requires a fast and reliable system for failure detection and their localization in the core. In the Prototype Fast Breeder Reactor, the system specially designed for this purpose is Failed Fuel Location Modules (FFLM) housed in the control plug region. It identifies a failed sub-assembly by detecting the presence of delayed neutrons in the sodium from a failed sub-assembly. During the commissioning phase of PFBR, it is mandatory to demonstrate the FFLM effectiveness. The paper highlights the engineering and physics design aspects of FFLM and the integrated simulation towards its function demonstration with a source assembly containing a perforated metallic fuel pin. This test pin mimics a MOX pin of 1 cm² of geometrical defect area. At 10% power and 20% sodium flow rate, the counts rate in the BCCs of FFLM system range from 75 cps to 145 cps depending upon the position of DN source assembly. The model developed for the counts simulation is applicable to both metal and MOX pins with proper values of k-factor and escape coefficient.

• Journal of Radiation Protection and Research
• /
• v.26 no.3
• /
• pp.167-175
• /
• 2001

Semiconductor diode detectors coated with neutron reactive material are presently under investigation for various uses, such as remote sensing of thermal neutrons, fast neutron counting, and thermal neutron radiography. Theory indicates that single-coated devices can yield thermal neutron efficiencies from 4% to 11 %, which is supported by experimental evidence. Radiation endurance measurements indicate that the devices function well up to a limiting thermal neutron fluence of $10^{13}/cm^2$, beyond which noticeable degradation occurs. Thermal neutron contrast images of step wedges and simple phantoms, taken with dual in-line pixel devices, show promise for thermal neutron imaging detectors.

• Nuclear Engineering and Technology
• /
• v.52 no.10
• /
• pp.2306-2312
• /
• 2020

Here we report on the first results of sensitivity evaluation of the gadolinium-aluminum-gallium- garnet (GAGG) scintillation detector with SiPM readout to fast and slow neutrons and, to the natural background and Co-60 γ-radiation as well. Data on sensitivity were obtained using certified dosimetry benches, so it can be utilized in the calculation of detection limits of neutron flux with such type of detectors. It was concluded that use of GAGG scintillator has a good prospect for neutron monitoring in different parts of nuclear research reactors and power plants.

• 전기의세계
• /
• v.29 no.2
• /
• pp.118-128
• /
• 1980

The properties of plasmas produced by high power glass laser were investigated with various methods of diagnostics. Electron temperature was estimated by measurement of soft X-ray, and ion temperature was estimated by measurement of the time-of-flight of ion. The measurement of incident and reflected laser light, and Schlieren and shadowgragh methods were also used. No influence of laser pulse duration on the temperature was observed in the case of durations 2, 4 and 10 nsecs. The effective heating of plasma occurred in about 2 nsec of beginning of incident laser pulse. The experimental results for fast rising laser pulse were discussed and the influence of resetime of laser pulse on the heating of plasma was described. Neutrons produced by irradiating laser beam to solid deuterium target were detected.

• Nuclear Engineering and Technology
• /
• v.53 no.7
• /
• pp.2075-2083
• /
• 2021

The article provides a review of the research results obtained during of more than 20 years concerning using the gaseous radiochemical method (GRCM) for detecting of ionizing radiation. This method based on threshold nuclear reactions with production of radioactive noble gas which does not interact with the materials of gaseous tract. The applications of GRCM in the diagnostics of neutrinos, neutrons, charged particles, thermonuclear plasma thermometry, and the study of the structure and dynamics of astrophysical objects, position-sensitive dosimetry of neutron targets with accelerator driving, spatial distribution of the fast neutron flux density in a nuclear reactor allowing the transformation of longitudinal coordinate of neutron flux distribution into a temporal distribution of the radiochemical gas decay counting rate ("barcode" semblance) and measurement of bombarding particles spectra are described. Experimental testing of the described technologies was made on the neutron target driven with the linear proton accelerator of Institute for Nuclear Research of Russian Academy of Sciences (INR RAS).

• Nuclear Engineering and Technology
• /
• v.51 no.3
• /
• pp.784-791
• /
• 2019

In the present study, a series of tungsten austenitic stainless steel alloys have been developed by interchanging the molybdenum in standard SS316 by tungsten. This was done to minimize the long-life residual activation occurred in molybdenum and nickel after decommissioning of the power plant. The microstructure and mechanical properties of the prepared alloys are determined. For the sake of increasing multifunction property of such series of tungsten-based austenitic stainless steel alloys, gamma shielding properties were studied experimentally by means of NaI(Tl) detector and theoretically calculated by using the XCOM program. Moreover, fast neutrons macroscopic removal cross-section been calculated. The obtained combined mechanical, structural and shielding properties indicated that the modified austenitic stainless steel sample containing 1.79% tungsten and 0.64% molybdenum has preferable properties among all other investigated samples in comparison with the standard SS316. These properties nominate this new composition in several nuclear application domains such as, nuclear shielding domain.

• Korean Journal of Veterinary Research
• /
• v.41 no.2
• /
• pp.203-210
• /
• 2001

Here, we compared the effectiveness of 50 MeV($p{\to}RBe^+$) cyclotron fast neutrons versus $^{60}Co$ ${\gamma}$-rays by the apoptotic fragment frequency in both rat peripheral lymphocytes and crypt cells to check a radiobiological endpoint. The incidence of apoptotic cell death was increased in all irradiated groups, and radiation at all doses trigger rapid changes in both crypt cells and peripheral lymphocytes. These data suggest that apoptosis may play an important role in homeostasis of damaged radiosensitive target organ by removing damaged cells. The curve of dose-effect relationship for these data of apoptotic fragments frequencies was $y=0.3+(6.512{\pm}0.279)D(r^2=0.975)$ after neutrons, while $y=0.3+(4.435{\pm}0.473)D+(-1.300{\pm}0.551)D^2(r^2=0.988)$ after ${\gamma}$-rays. In addition, $y=3.5+(118.410{\pm}10.325)D+(-33.548{\pm}12.023)D^2(r^2=0.992)$ after ${\gamma}$-rays in rat lymphocytes. A significant dose-response relationship was found between the frequency of apoptotic cell and dose. These data show a trend towards increase of the numbers of apoptotic cells with increasing dose. Dose-response curves for high and low linear energy transfer (LET) radiation modalities in these studies were different. The relative biological effectiveness (RBE) value for crypt cells was 1.919. In addition, there were significant peaks on apoptosis induction at 4 and 6h after irradiation, and the morphological findings of the irradiated groups were typical apoptotic fragments in crypt cells that were hardly observed in the control group. Thus, apoptosis induction in both crypt cells and peripheral lymphocytes could be a useful endpoint of rat model for studying screening test and microdosimetic indicator to evaluate the biological effects of radiation-induced cell damage.

• Nuclear Engineering and Technology
• /
• v.27 no.1
• /
• pp.74-83
• /
• 1995

The accurate determination of the fast neutron flux/fluence onto the pressure vessel is an essential part of the reactor pressure vessel surveillance program. It has been reported recently that the iron cross section data in ENDF/B versions III through V might underestimate the flux/fluence of fast neutrons in steel structures such as reactor pressure vessel. In this study, for the comparison of iron data of ENDF/B-IV and VI we produced two 47-group cross section sets, CXFe-IV and CXFe-Ⅵ, which are based on Yonggwang nuclear unit-3/4 model and the iron data of ENDF/B-IV and VI, respectively. A comparison was made of the results obtained from DOT4.3 calculation using CXFe-IV and CXFe-VI. From the results, it was found that the fast flux(E 〉 1.0 MeV), which is important for the pressure vessel embrittlement analysis, increases by about 7.6％ at the inner wall and 20％ at the outer wall of the vessel, if the iron data are used from ENDF/B-VI instead of ENDF/B-IV.

• Nuclear Engineering and Technology
• /
• v.51 no.5
• /
• pp.1444-1450
• /
• 2019

The fast-neutron shielding behaviour (FNSB) of two clay-materials (Ball clay and Kaolin)of Southwestern Nigeria ($7.49^{\circ}N$, $4.55^{\circ}E$) have been investigated using effective removal cross section, ${\Sigma}_R(cm^{-1})$, mass removal cross section, ${\Sigma}_{R/{\rho}}(cm^2g^{-1})$ and Mean free path, ${\lambda}$ (cm). These parameters decide neutron shielding behaviour of any material. A computer program - WinNC-Toolkit has been used for computation of these parameters. The toolkit evaluates these parameters by using elemental compositions and densities of samples. The proficiency of WinNC-Toolkit code was probe by using MCNPX and GEANT4 to model fast neutron transmission of the samples under narrow beam geometry, intending to represent the actual experimental setup. Direct calculation of effective removal cross section ($cm^{-1}$) of the samples was also carried out. The results from each of the methods for each types of the studied clay-materials (Ball clay and Kaolin) shows similar trend. The trend might be the fingerprint of water content retained in each of the samples being baked at different temperature. The compositions of each sample have been obtained by Particle-Induced X-ray Emission (PIXE) technique (Tandem Pelletron Accelerator: 1.7 MV, Model 5SDH). The FNSB of the selected clay-materials have been compared with standard concrete. The cognizance of various factors such as availability, thermo-chemical stability and water retaining ability by the clay-samples can be analyzed for efficacy of the material for their FNSB.

• Nuclear Engineering and Technology
• /
• v.53 no.2
• /
• pp.423-429
• /
• 2021

The investigation of the utilization of enriched ²⁰⁸Pb as a coolant to enhance the performance of a long-life fast reactor with a Modified CANDLE (Constant Axial shape of Neutron flux, nuclide densities, and power shape During Life of Energy production) burnup scheme has performed. The analyzes were performed on a reactor with thermal power of 800 MegaWatt Thermal (MWTh) with a refueling process every 15 years. Uranium Nitride (enriched ¹⁵N), ²⁰⁸Pb, and High-Cr martensitic steel HT-9 were employed as fuel, coolant, and cladding materials, respectively. One of the Pb-nat isotopes, ²⁰⁸Pb, has the smallest neutron capture cross-section (0.23 mb) among other liquid metal coolants. Furthermore, the neutron-producing cross-section (n, 2n) of ²⁰⁸Pb is larger than sodium (Na). On the other hand, the inelastic scattering energy threshold of ²⁰⁸Pb is the highest among Na, ^natPb, and Bi. The small inelastic scattering cross-section of ²⁰⁸Pb can harden the neutron energy spectrum. Therefore, ²⁰⁸Pb is a better neutron multiplier than any other liquid metal coolant. The excess neutrons cause more production than consumption of ²³⁹Pu. Hence, it can reduce the initial fuel loading of the reactor. The selective photoreaction process was developing to obtain enriched ²⁰⁸Pb. The neutronic was calculated using SRAC and JENDL 4.0 as a nuclear data library. We obtained that the modified CANDLE reactor with enriched ²⁰⁸Pb as coolant and reflector has the highest k-eff among all reactors. Meanwhile, the ^natPb cooled reactor has the lowest k-eff. Thus, the utilization of the enriched ²⁰⁸Pb as the coolant can reduce reactor initial fuel loading. Moreover, the enriched ²⁰⁸Pb-cooled reactor has the smallest power peaking factor among all reactors. Therefore, the enriched ²⁰⁸Pb can enhance the performance of a long-life Modified CANDLE fast reactor.