• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.8
• /
• pp.688-693
• /
• 2000

In this paper an optical voltage sensor and an optical current sensor which can be used for the measurement of impulse voltage and current are implemented. BSO single crystal is utilized as a voltage sensor(Pockels effect cell). An rare earth doped YIG is used as a current sensor(Faraday effect cell). A new signal processing technique is adopted not only to avoid the influences o external optical fiber pertubations of transmitting optical fiber but also to improves the frequency response characteristics of the fiber-optic voltage and current sensors. Experimental results show that optical voltage sensor has maximum 2.5% error within the voltage range from 0V to 500V. and optical current sensor has maximum 2.5% error within the current range and that of optical current sensor is about 1.5% within temperature range from -2$0^{\circ}C$ to 6$0^{\circ}C$. The proposed optical sensors have good frequency response characteristics within the frequency range from DC to 10MHz.

• Transactions of the Korean hydrogen and new energy society
• /
• v.32 no.6
• /
• pp.470-476
• /
• 2021

In the near future, with the urgent requirement of environmental protection, hydrogen based energy system is essential. However, at the present time, most of the hydrogen is produced by reforming, which still produces carbon dioxide. This study proposes a high-power electrolytic hydrogen production system based on solid oxide electrolysis cell with no harmful emissions to the environment. Besides that, the parametric study and optimization are also carried to examine the effect of individual parameter and their combination on system efficiency. The result shows that the increase in steam conversion rate and hydrogen molar fraction in incoming stream reduces system efficiency because of the fuel heater power increase. Besides, the higher Faraday efficiency does not always result a higher system efficiency.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.4
• /
• pp.337-342
• /
• 2022

In this study, a water electrolysis was studied to investigate the effect of ammonia on current density and H2 gas production. A H type cell with three electrodes was used and KOH solution was used as electrolyte. The conventional platinum foil was used for working electrode, whereas nickel foam was used for counter electrode. CV experiment was performed to see the activity of ammonia oxidation reaction. In addition, CP experiment was done to examine the dependence of Faraday efficiency of hydrogen on current density and NH3 concentration. The CV result shows the 0.5M NH3 concentration required for highest current density and reliable operation. The CP result shows the increased current density leads to higher H2 generation. The higher H2 production and subsequent energy efficiency was observed for 0.5M NH3 using a Pt/13%Rh coil for a cathode as compared to those in water electrolysis.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.12
• /
• pp.2250-2255
• /
• 2010

An fine silver particle has a variety of uses, such as in killing micrograms and as catalysts. Many techniques have been used for the production of the fine particles. Faraday cell, consisting of two silver electrodes in an electrolyte, is unique, but it is hard to get a very fine particle by this method. A finer silver nano-particle producing cell, utilizing a dielectric bed as a lower electric current and higher field controlling means, has been proposed and investigated. The I-V characteristics of the cell and effect of the dielectric bed on the producing finer silver nano-particles have been investigated. The I-V characteristics of the cell with the dielectric bed were different from that of the same system without the bed, due to the increased cell resistance and elevated electric field intensity. It is found that the proposed cell with the dielectric bed can produce finer silver nano-particles effectively, which, however, can be used as one of effective fine silver nano-particle producing means.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.03a
• /
• pp.90-106
• /
• 1995

The "O"S' BONDING make metallic and non-metalic crystal structures and form localized superconducting orbitals , which induce electrical conduction , semi-conduction, and superconduction. The orbitals are proced by Ampere's law, Faraday's law , Meissner effect, highcritical temperature of thecopper oxide layers. abnomal trans-membrane signal in cancer cell and plastic deformations bytwins and dislocations, In the case of alloying metals, the most deterimentla cases of electrical conduction are those of solid solution and intermetalic compound . The highest case for the hardness are also those of solid solution and intermetallic compound. It explains the contributions of the "O"S' BONDING for conduction bands and plastic deformation by twins and dislocations.ns and dislocations.

• Korean Journal of Optics and Photonics
• /
• v.16 no.1
• /
• pp.7-12
• /
• 2005

We have observed the nonlinear magneto-optic effect(NMOE) based on atomic coherence in $^{87}$ Rb D$_1$-line using the Rb vapor cell containing 50 Torr of Ne. The width of the NMOE signal was measured to be 2$\pi$${\times}$464 Hz, when the peak-to-peak B-field variation was 1 mGauss. The result of this work may be applied to a high-sensitivity magnetometer.

• Korean Journal of Optics and Photonics
• /
• v.17 no.1
• /
• pp.1-6
• /
• 2006

We investigated the characteristics of the nonlinear magneto-optic effect (NMOE) depend on the transitions, the laser intensity and the temperature of the vapor cell, in the $D_1$ transition of $^{87}Rb$ atoms by using the Rb vapor cell contained with buffer gas of Ne 6.7 kPa. The size and the width of NMOE signal were increased according to the light intensity and temperature in the transition of F=2$\to$F'=2. However, In the case of using the F=2$\to$F'=1 transition, the size of the signal could be increased according to the light intensity without additional broadening of the width. We confirmed that the sensitivity of detecting small magnetic flux improved in this transition, and explained these effects by the different of the CPT configuration between Zeeman sublevels. At the optimal condition in experiment, the sensitivity of this system was evaluated less then $70pT/\sqrt{Hz}$.

• Nuclear Engineering and Technology
• /
• v.42 no.2
• /
• pp.183-192
• /
• 2010

An electrochemical reduction of a mixture of metal oxides was conducted in a LiCl molten salt containing 3 wt% $Li_2O$ at $650^{\circ}C$. The oxide reduction was carried out by applying a current to an electrolysis cell, and the $Li_2O$ concentration was analyzed during each run. The concentration of $Li_2O$ in the electrolyte bulk phase gradually decreases according to Faraday's law due to a slow diffusion of the $O^{2-}$ ions. A hindrance effect of the unreduced metal oxides was observed for the reduction of the uranium oxide. Cs, Sr, and Ba of high heat-load fission products were diffused into and accumulated in the salt phase as predicted with thermodynamic consideration.

• Tribology and Lubricants
• /
• v.31 no.3
• /
• pp.79-85
• /
• 2015

RC delay is a critical issue for achieving high performance of ULSI devices. In order to minimize the RC delay time, we uses the CMP process to introduce high-conductivity Cu and low-k materials on the damascene. The low-k materials are generally soft and fragile, resulting in structure collapse during the conventional high-pressure CMP process. One troubleshooting method is electrochemical mechanical polishing (ECMP) which has the advantages of high removal rate, and low polishing pressure, resulting in a well-polished surface because of high removal rate, low polishing pressure, and well-polished surface, due to the electrochemical acceleration of the copper dissolution. This study analyzes an electrochemical state (active, passive, transpassive state) on a potentiodynamic curve using a three-electrode cell consisting of a working electrode (WE), counter electrode (CE), and reference electrode (RE) in a potentiostat to verify an electrochemical removal mechanism. This study also tries to find optimum conditions for ECMP through experimentation. Furthermore, during the low-pressure ECMP process, we investigate the effect of current density on surface roughness and removal rate through anodic oxidation, dissolution, and reaction with a chelating agent. In addition, according to the Faraday’s law, as the current density increases, the amount of oxidized and dissolved copper increases. Finally, we confirm that the surface roughness improves with polishing time, and the current decreases in this process.