• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.5
• /
• pp.1310-1318
• /
• 1998

Sigma-delta converter is frequently used for conyerting low-frequency anglog to digital signal. The converter consists of a modulator and a digital filer, but our work is concentrated on the modulator. In this works, to design second-order sigma-dalta modulator with 14bit resolution, we define maximumerror limits of each components (operational smplifier, integrator, internal ADC, and DAC) of modulator. It is first performed modeling of an ideal second-order sigma-delta modulator. This is then modified by adding the non-ideal factors such as limit of op-amp output swing, the finit DC gain of op-amp slew rate, the integrator gian error by the capacitor mismatch, the ADC error by the cmparator offset and the mismatch of resistor string, and the non-linear of DAC. From this modeling, as it is determined the specification of each devices requeired in design and the fabrication error limits, we can see the final performance of modulator.

• Journal of Power Electronics
• /
• v.15 no.6
• /
• pp.1673-1681
• /
• 2015

A low dropout (LDO) regulator with a wide-bandwidth is proposed in this paper. The regulator features a Human Body Model (HBM) 8kV-class high robustness ElectroStatic Discharge (ESD) protection circuit, and two error amplifiers (one with low gain and wide bandwidth, and the other with high gain and narrow bandwidth). The dual error amplifiers are located within the feedback loop of the LDO regulator, and they selectively amplify the signal according to its ripples. The proposed LDO regulator is more efficient in its regulation process because of its selective amplification according to frequency and bandwidth. Furthermore, the proposed regulator has the same gain as a conventional LDO at 62 dB with a 130 kHz-wide bandwidth, which is approximately 3.5 times that of a conventional LDO. The proposed device presents a fast response with improved load and line regulation characteristics. In addition, to prevent an increase in the area of the circuit, a body-driven fabrication technique was used for the error amplifier and the pass transistor. The proposed LDO regulator has an input voltage range of 2.5 V to 4.5 V, and it provides a load current of 100 mA in an output voltage range of 1.2 V to 4.1 V. In addition, to prevent damage in the Integrated Circuit (IC) as a result of static electricity, the reliability of IC was improved by embedding a self-produced 8 kV-class (Chip level) ESD protection circuit of a P-substrate-Triggered Silicon Controlled Rectifier (PTSCR) type with high robustness characteristics.

• Design & Manufacturing
• /
• v.1 no.1
• /
• pp.7-11
• /
• 2007

The fabrication of precision optical components by deterministic CNC grinding is an area of great current interest. Replacement of the traditional, craftsman driven, optical fabrication process is essential to reduce costs and increase process flexibility and reliability. Moreover, CNC grinding is well suited to the fabrication of complex shapes such as aspheres, making it possible to design optical systems with fewer components and reduced weight. Current technology is capable of producing surfaces with less than 2 microns peak to valley error, 50 nm rms surface roughness, and less than 1 micron subsurface damage. Bound abrasive tools, in which the abrasive particles are fixed in a second (matrix) material, play an important part in achieving this performance. In this paper, the factors affecting the ultra-fine surface roughness and profile accuracy of machined surfaces of aspheric parts has been analyzed experimentally and theoretically and on ultra-precision aspheric grinding system and precise adjusting mechanism have been designed and manufactured. In the paper we report the results of experiments and modeling performed to examine the effects of machinability, occurring during grinding of optical surfaces, on the tool surface profile. Profiles of machined surface were measured by using SEM. In order to optimize grinding conditions of aspheric lens processing, we performed experiments by design of experiments.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.4
• /
• pp.38-44
• /
• 2000

In this paper, we have been fabricated λ/2 phase plates lot an optical pick-up using a blue violet laser diode by employing proton exchange and wet etching in LiNbO$_{3}$. Their functions and fabrication processes are described in detail. It is established the optimal fabrication conditions through the experimental results. The device characteristics are measured by the Mach-zender interferometer which is composed of the optical components and 632.8nm He-Ne laser. The measured phase error was ＋5$^{\circ}$~ -6$^{\circ}$(within 3%). This phase plate could be applied an useful device to improve the resolution and the stability of the optical pick-up which has a blue violet laser diode as an optical source.

• The Magazine of the IEIE
• /
• v.21 no.11
• /
• pp.75-85
• /
• 1994

Safety and Reliability assessments of Avionics Parts must be conducted essentially in the step of disign and manufacture as it constitutes a major field of aircraft critical operation. Recently Avionics parts fabrication techniques are continuously developing by applying digital techniques. Airborne computer is being adopted on an aircraft for flight is being adopted on an aircraft for flight safety augmentation and simplification of controls including reduction of human error. Therefore inspection and evaluation procedures should be developed in order to accomodate such trends. The number of avionics parts is approximitely 72% of total TSO parts, so it is expected high added-values through manufactures of TSO parts in aircraft industries. Particuarly avionics parts must be manufacturered with our own technology to be used in Mid-class aircraft which will be developed soon. Along with this, preparation of Certification Procedures is essential for Avionics Parts.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.7
• /
• pp.734-740
• /
• 2003

In this paper, A Vector Modulator based a wideband analog phase shifter is realized with four P-I-N diode attenuators, an asymmetric coupled line coupler, a symmetric coupled line coupler, and a power combiner. Simple configuration to have advantages in cost, size, power, and the number of passive circuits is presented. The phase variation due to phase and amplitude error of a P-I-N diode attenuator is derived and used to optimize the overall circuit. The phase shifter shows a total phase shift of 360$^{\circ}$, a 8.2$^{\circ}$maximum phase error, and a 16${\pm}$2.5 dB insertion loss over the wide frequency range of 1 GHz to 3 GHz.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.3
• /
• pp.529-536
• /
• 2001

We investigate a surface-micromachined capacitive accelerometer with the grid-type electrodes surrounded by a perforated proof-mass frame. An electromechanical analysis of the microaccelerometer has been performed to obtain analytical formulae for natural frequency and output sensitivity response estimation. A set of prototype devices has been designed and fabricated based on a 4-mask surface-micromachining process. The resonant frequency of 5.8$\pm$0.17kHz and the detection sensitivity of 0.28$\pm$0.03mV/g have been measured from the fabricated devices. The parasitic capacitance of the detection circuit with a charge amplifier has been measured as 3.34$\pm$1.16pF. From the uncertainty analysis, we find that the major uncertainty in the natural frequency of the accelerometer comes from the micromachining error in the beam width patterning process. The major source of the sensitivity uncertainty includes uncertainty of the parasitic capacitance, the inter-electrode gap and the resonant frequency, contributing to the overall sensitivity uncertainty in the portions of 75%, 14% and 11%, respectively.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.219-223
• /
• 2003

This paper describes an estimation of DOA(Direction Of Arrival) measurement system using DBF receiver with linear array antenna. This DBF receiver is composed of resistive FET mixer using low IF mettled. A radio frequency(RF), a local oscillator(LO) and ail intermediate frequency(IF) considered in this research are 2.09 GHz, 2.08 GHz and 10 MHz, respectively. This receiver is composed of a band-pass filter, a low-pass filter, a DC bias circuit. DOA measurement system is consist of linear array antenna, DBF receiver, AD control box and computer in the anechoic chamber. Receiving antenna is 4-array monopole antenna and DBF receiver is 4-Ch resistive FET mixer without amplifier. DOA algorithm is implemented using MUSIC algorithm with high resolution. We show that the results of DOA is $-30^{\circ},\;0^{\circ}$ and $60^{\circ}$, respectively. And we know that DOA estimation error occur by antenna radiation pattern and fabrication error of antenna array.

• Transactions of Materials Processing
• /
• v.24 no.2
• /
• pp.121-129
• /
• 2015

A net-shape forming of small and complex-shaped metal parts by metal injection molding (MIM) has economic advantages in mass production, especially for STS 316L valve fitting. STS 316L offers excellent corrosion resistance, but it has poor machinability, which is a limitation in using it for a cost-effective production where both forging and machining are employed. Simulation and experimental analysis were performed to develop a MIM STS 316L 90° elbow fitting minimizing trial and error. A Taguchi method was used to determine which input parameter was the most sensitive to possible defects (e.g. sink mark depth) during the injection molding. The final prototype was successfully built. The results indicate that the simulation tool can be used during the design process to minimize trial and error, but the final adjustment of parameters based on field experience is essential.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.8
• /
• pp.1604-1611
• /
• 2003

For dual­band operation, it can be done by loading two pair of slits in the equilateral­triangular patch, one embeded close to the side edges of the patch and the other inserted at the bottom edge of the patch. The frequency ratio of the two operating frequencies can be tuned by varing the positions and lengths of the inserted slots at the bottom edge of the patch. While the calculated frequency ratio of the antenna by Ensemble 5.0 is $1.66 ({f_10}=1.928GHz, {f_20}=3.2GHz)$, the measured one is 2.04 $({f_10}=1.6806 GHz, {f_20}=3.435 GHz)$. The error in the frequency ratio is due on the fabrication dimension and feeding position error as well as on the permittivity dispersion effect.