• Journal of information and communication convergence engineering
• /
• v.13 no.2
• /
• pp.81-85
• /
• 2015

A 94-GHz phased array antenna using a log-periodic antenna has been developed on a GaAs substrate. The developed phased array antenna comprises four log-periodic antennas, a phase shifter, and a Wilkinson power divider. This antenna was fabricated using the standard microwave monolithic integrated circuit (MMIC) process including an air bridge for unipolar circuit implementations on the same GaAs substrate. The total chip size of the fabricated phased array antenna is 4.8 mm × 4.5 mm. Measurement results showed that the fabricated phased array antenna had a very wide band performance from 80 GHz to 110 GHz with return loss characteristics better than -10 dB. In the center frequency of 94 GHz, the fabricated phased array antenna showed a return loss of -16 dB and a gain of 4.43 dBi. The developed antenna is expected to be widely applied in many applications at W-band frequency.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.506-510
• /
• 2003

In this paper, a meander-line chip antenna with stacked layer is suggested, designed and fabricated employing the LTCC(Low Temperature Co-fired Ceramic) fabrication techniques. To reduce the antenna chip size, the meander-line antenna strip is distributed over three layer. Layers one interconnected using via holes. A 2.4 GHz chip antenna with size of $3.75{\times}7.9{\times}1.0 mm^3$ is designed and fabricated using the LTCC technique. Measurements of the fabricated antenna show 160 MHz bandwidth and 3.75 dBi maximum gain. The Measured reflection coefficient and radiation patterns agree well with the prediction by electromagnetic simulation.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.478-483
• /
• 2003

In this paper, in order to fabricate the circularly polarized diversity system which will mitigate multipath fading, 5.8GHz band microstrip array antenna were designed and fabricated. These antenna were designed using Ensemble 6.0 program and the fabricated antenna were vertical and horizontal polarized antenna, left-handed circularly polarized antenna, and right-handed circularly polarized antenna. The designed antenna parameters included S11 and impedance characteristics of fabricated antenna were measured using Network Analyzer(8753ES). From the measurement results, the S11 for each polarization antenna at resonance frequency of 5.8GHz band was showed -38dB, -44dB, and -50dB respectively and it was similar to the simulation result, and also the impedance can be matched at $50{\Omega}$. In order to compare polarization characteristics, broadband measurement was also conducted in this paper.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.4
• /
• pp.170-175
• /
• 2004

A three dimensional feed horn 10${\mu}{\textrm}{m}$ wavelength infrared antenna has been suggested, fabricated and characterized. It was applied to an infrared detector for efficient collecting of IR radiation and for reducing background noise. The horn antenna size was designed for maximum antenna directivity. The 3D feed horn antenna mold was fabricated using rotating and tilted illumination while the antenna plate was constructed by way of electroplating. Antenna characteristics were measured by coupling with a microbolometer. Measurement results indicated that the directivity of the antenna is 16.1㏈ and the background noise is reduced by approximately two times.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.4
• /
• pp.320-323
• /
• 2018

Herein, an ultrawideband spinning direction finding (DF) antenna was designed and fabricated for airborne applications. The proposed antenna is designed by dividing the low-band (UHF - L band) and high-band (S - Ka band) antennas to cover the ultrawideband frequency range (UHF - Ka band). For the high-band antenna, an LPDA antenna fed offset-parabolic-reflector antenna is applied. In the low-band antenna, two LPDA antenna elements are arrayed in front of the reflector of the high-band antenna without increasing to the full antenna size. The low- and high-band gains of the fabricated antenna were measured as 8.76 dBi and 24.55 dBi on average, respectively. The antenna was fabricated with the dimensions of 437 mm in diameter and 358 mm in height. Consequently, we confirmed that the designed antenna is appropriate for the spinning DF antenna in terms of the affordable size for installing on an airplane, as well as the high gain and narrow beamwidth.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.580-583
• /
• 2007

In this paper, we proposed a slot antenna for dual band ISM that was transformed from a slot antenna structure. Proposed antenna was designed and fabricated that transformed feed line was changed existing slot antenna feed line to appear resonances at dual band. Bandwidth of the designed and fabricated slot antenna for ISM dual band is 8.23%, 4.8% at the resonated frequency at 2.45 GHz, 5 GHz. And we observed the resonant frequency and bandwidth according to change of feed line and slot length. Also, the measured radiation pattern characteristic of fabricated antenna is compared and analyzed E-plane and H-plane at 2.45 GHz, 5GHz.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.9
• /
• pp.832-837
• /
• 2006

Antennas were fabricated by physical(adhesive) and chemical(deposition+plating) method on organic-inorganic composite material. And antennas were measured dielectric constant and gain. Dielectric constant of antennas were fabricated by physical method was decreased with increase of adhesive tape thickness and number of conduction material composition. But antennas were fabricated by chemical method was reached to 90 % of dielectric material. Gain of antennas were fabricated by physical method was decreased with increase of adhesive tape thickness. But they were unrelated with conduction material composition. The other side antennas were fabricated by chemical method excelled more 0.8 dBic than antennas were fabricated by physical method in gain of antenna. Finally, chemical method can expect excellent product process because it can produce smaller size, higher gain and elimination of many handworks.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.10
• /
• pp.3880-3884
• /
• 2010

In this paper, circularly polarized micro-strip GPS antenna has been designed and fabricated. In order to improve of frequency properties, patch size, corner truncated size and feed positions were simulated using HFSS simulation program. Micro-strip GPS antenna was fabricated on the FR4 substrate of dielectric constant 4.4. The fabricated GPS antenna has that center frequency is 1.575GHz and insertion loss is -34.50dB.

• Journal of Korea Society of Industrial Information Systems
• /
• v.19 no.1
• /
• pp.19-24
• /
• 2014

In this work, a compact patch antenna based on a low temperature cofired ceramic (LTCC) has been presented for V-band system-on-package (SoP) applications. In order to integrate it with transceiver block, a waveguide (W/G) to embedded microstrip line (eMSL) vertical transition was designed using slot-fed double stacked patch antennas for easy assembly and wide bandwidth. The $2{\times}2$ patch antenna integrating the transition was designed and fabricated in the 5-layer LTCC dielectrics. The whole size of the fabricated antenna including the $2{\times}2$ patches, transition and W/G was $20{\times}24{\times}5.39mm^3$. The fabricated antenna has achieved a 10 dB impedance bandwidth of 2.45 GHz from 61 to 63.45 GHz.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.5
• /
• pp.221-227
• /
• 2013

In this paper, Satellite DMB/WiBro antenna and PCS/WiBro antenna improving indoor coverage for mobile services are designed and fabricated. Satellite DMB/WiBro bands repeater antenna and PCS/WiBro bands repeater antenna are proposed as a simple radiator with loading capacitor to generate LHCP(Left Hand Circular Polarization). The proposed antenna for Satellite DMB/WiBro and PCS/WiBro bands communication are fabricated by copper plate uploader type and substrate uploader type. The designed and fabricated antenna has a bandwidth of 70MHz at 1.816GHz~1.886GHz and bandwidth of 107MHz at 2.247GHz~2.354GHz. Maximum gain of radiation pattern was up to 5dBi.