• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.316-317
• /
• 2018

Thailand and other Southeast Asian countries are experiencing frequent floods due to heavy rainfall and are using the Flood Rapid Defense System(FRDS) for an emergency. However, they are expensive and has a wedge-shaped panel suitable for the dirt bank, making it unsuitable for applications in Southeast Asia, a relatively underdeveloped country. In this study, the direction of development of FRDS was derived through domestic and overseas case analysis. Future studies should be carried out to develop the actual FRDS according to the development directions presented here. These results will be effective in preventing flooding of buildings in Southeast Asia as well as in Korea.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.8-17
• /
• 2018

A large urban region in Bangkok, Thailand is often inundated due to shallow water floods along the paved roads that have poor drainage facilities, and that can cause urban flooding. Existing methods, including using sand bags are not effective to prevent flooding in urban areas where the amount of sand is not sufficient. Thus, it is necessary to install artificial flood defense structures. However flooding and overflow defense equipment, which was developed in some advanced nations in Europe and in the USA, is highly expensive and complex construction methods are needed, therefore they are not suitable to be used in Southeast Asia. Thus, it is necessary to develop a flood rapid defense system(FRDS), which is inexpensive and simple to build, but is also highly functional. Thus, this study developed an FRDS that can be applied to Southeast Asia through the careful study of FRDS overviews, an analysis on the development trends in Korea and overseas, and the proposal of development needs and directions of the region. For the system developed, Korean Standards(KS) performance evaluations on leakage ratio deformation tests and impact resistance tests were conducted at the Outdoor Demonstration Test Center(Seosan) in the Korea Conformity Laboratories(KCL) and the system satisfied the standards of KS F 2639(leakage and deformation test) and KS F 2236(impact resistance test). The present study results can not only be applied to urban floods in Southeast Asian nations to cope with flood-related disasters, but also be utilized in flood prone regions and for major facilities in Korea. They can also induce scientific and pro-active responses from major local governments and facility management organizations in relation to urban floods.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.4
• /
• pp.495-502
• /
• 2014

Fast recovery diodes (FRDs) were developed using the $p^{{+}{+}}/n^-/n^{{+}{+}}$ epitaxial layers grown by low temperature epitaxy technology. We investigated the effect of electrostatic discharge (ESD) stresses on their electrical and switching properties using current-voltage (I-V) and reverse recovery time analyses. The FRDs presented a high breakdown voltage, >450 V, and a low reverse leakage current, < $10^{-9}$ A. From the temperature dependence of thermal activation energy, the reverse leakage current was dominated by thermal generation-recombination and diffusion, respectively, at low and high temperature regions. By virtue of the abrupt junction and the Pt drive-in for the controlling of carrier lifetime, the soft reverse recovery behavior could be obtained along with a well-controlled reverse recovery time of 21.12 ns. The FRDs exhibited excellent ESD robustness with negligible degradations in the I-V and the reverse recovery characteristics up to ${\pm}5.5$ kV of HBM and ${\pm}3.5$ kV of IEC61000-4-2 shocks. Likewise, transmission line pulse (TLP) analysis reveals that the FRDs can handle the maximum peak pulse current, $I_{pp,max}$, up to 30 A in the forward mode and down to - 24 A in the reverse mode. The robust ESD property can improve the long term reliability of various power applications such as automobile and switching mode power supply.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.589-592
• /
• 2002

The CCM (Continuous Conduction Mode) boost topology is generally used in the PFC (Power Factor Correction) regulator of household air-conditioning systems. There are three kinds of power devices-bridge rectifier diodes, FRDs (Fast Recovery Diodes), and IGBTs (or MOSFETs) - used In a boost PFC regulator. Selecting the appropriate device is very cumbersome work, specially, in the case of FRDs and IGBTs, because there are several considerations as described below: 1) High frequency leakage current regulation (conducted and radiated EMI regulation) 2) Power losses and thermal design 3) Device cost. It should be noted that there are trade-offs between the power loss characteristic of 2) and the other characteristics of 1) and 3). This paper presents a detailed evaluation by using several types of power devices, which can be unintentionally used, to show that optimal selection can be achieved. Based on the given thermal resistances, thermal analysis and design procedures are also described from a practical viewpoint.

• Wind and Structures
• /
• v.10 no.3
• /
• pp.233-247
• /
• 2007

The insertion of steel braces has become a common technique to limit the deformability of steel framed buildings subjected to wind loads. However, when this technique is inadequate to keep floor accelerations within acceptable levels of human comfort, dampers placed in series with the steel braces can be adopted. To check the effectiveness of braces equipped with viscoelastic (VEDs) or friction dampers (FRDs), a numerical investigation is carried out focusing attention on a three-bay fifteen-storey steel framed building with K-braces. More precisely, three alternative structural solutions are examined for the purpose of controlling wind-induced vibrations: the insertion of additional diagonal braces; the insertion of additional diagonal braces equipped with dampers; the insertion of both additional diagonal braces and dampers supported by the existing K-braces. Additional braces and dampers are designed according to a simplified procedure based on a proportional stiffness criterion. A dynamic analysis is carried out in the time domain using a step-by-step initial-stress-like iterative procedure. Along-wind loads are considered at each storey assuming the time histories of the wind velocity, for a return period $T_r=5$ years, according to an equivalent wind spectrum technique. The behaviour of the structural members, except dampers, is assumed linear elastic. A VED and an FRD are idealized by a six-element generalized model and a bilinear (rigid-plastic) model, respectively. The results show that the structure with damped additional braces can be considered, among those examined, the most effective to control vibrations due to wind, particularly the floor accelerations. Moreover, once the stiffness of the additional braces is selected, the VEDs are slightly more efficient than the FRDs, because they, unlike the FRDs, dissipate energy also for small amplitude vibrations.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.8
• /
• pp.1394-1400
• /
• 2010

This paper introduces a newly improved Ultra-FRFET that has much better reverse recovery characteristic than that of the typical MOSFET and presents its effectiveness in the HV-BLU system of LCD TVs. The reverse recovery time, $T_{rr}$ of Ultra-FRFET is shorter than 40nsec and the peak value of reverse current, $i_{rr}$ is also much smaller compared to the typical MOSFET's, which are sufficient to prevent the MOSFET’s failures without additional FRDs and diodes in HV-BLU system with a half-bridge resonant inverter topology worked by PWM method. In order to verify the validity, the loss analysis and the implementation results in cases when both the conventional solution using typical MOSFETs with additional FRDs and a new solution using Ultra-FRFETs are applied to a HV-BLU of 40" LCD TV are presented. As a result, the effectiveness of Ultra-FRFET was verified and the results are presented in this paper.

• Journal of Power Electronics
• /
• v.11 no.2
• /
• pp.188-193
• /
• 2011

A highly efficient AC-DC converter for small wind power generation systems using a brushless DC generator (BLDCG) is presented in this paper. The market standard AC-DC converter for a BLDCG consists of a three-phase diode rectifier and a boost DC-DC converter, which has an IGBT and a fast recovery diode (FRD). This kind of two-stage solution basically suffers from a large amount of conduction loss and the efficiency greatly decreases under a light load, or at a low current, because of the switching devices with a P-N junction. In order to overcome this low efficiency, especially at a low current, a three-phase bridgcless converter consisting of three upper side FRDs and three lower side Super Junction FETs is presented. In the overall operating speed region, including the cut-in speed, the efficiency of the proposed converter is improved by up to 99%. Such a remarkable result is validated and compared with conventional solutions by calculating the power loss based on I-V curves and the switching loss data of the adopted commercial switches and the current waveforms obtained through PSIM simulations.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.5
• /
• pp.475-486
• /
• 2016

Four-rotor dish-shaped unmanned underwater vehicles (FRDS UUVs) are new type underwater vehicles. The main goal of this paper is to develop a quick method to optimize the design of hydraulic support landing platform for the new UUV. In this paper, the geometry configuration and instability type of the platform are defined. Computational investigations are carried out to study the hydrodynamic performance of the landing platform using the Computational Fluid Dynamics (CFD) method. Then, the response surface model of the optimization objective is established. The intelligent particle swarm optimization (PSO) is applied to finding the optimal solution. The result demonstrates that the stability of landing platform is significantly improved with the global objective index increasing from 1.045 to 1.158 (10.86% higher) after the optimization process.