• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.709-716
• /
• 2003

Flexible pipes (corrugated polyethylene pipes) are normally used for underground power distribution grids. In this paper, dynamic analysis was carried out through FEM in order to investigate the structural behaviour of pipes subjected to seismic loads. The burial depth and the number of pipes were major parameters in the numerical analysis to determine the response of pipes. The results show that the displacement of pipes under given conditions are all satisfactory in comparison of the allowable strain criteria -maximum 3.5 %.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.61-63
• /
• 2002

This paper deals with the design of vaccum pump using moving magnet type linear oscillaory actuator based on the design procedure and the characteristic analysis. To improve the starting characteristic, the optimum spring constant is detected and redesigned. The parameter was calculated by Finite Element Method(FEM). In order to dynamic characteristic analysis. Time difference method with voltage and kinetic equation is used.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 B
• /
• pp.253-255
• /
• 2000

This paper describes the operating characteristic analysis of PM-type magnetic circuit breaker for electromagnetic field, electric circuit and mechanical motion problems. Transient calculations based up 2D finite element magnetic field solution including non-linearity of materials. Change of dynamic characteristic from eddy current in mover is quantified from FEM analysis.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1590-1594
• /
• 2007

This paper describes a case study on dynamic characteristics analysis of a 5-axis multi-tasking machine tool of ram-head typed. Natural frequency and corresponding vibration modes of the machine tool structure were obtained by using both FEM modal analysis and an experimental modal test(impulse hammer test). Both the theoretical and experiment analysis results showed good agreement with each other. Finally, some discussion and review, from the view point of resonance vibration and/or mode coupled chatter, were made based on the analysis results.

• 한국공작기계학회논문집
• /
• 제13권1호
• /
• pp.81-87
• /
• 2004

A 3-D FEM (Finite Element Method) analysis of the turbo-blower shaft attached to a fuel cell was performed using Lanczos algorithm. The modal analysis was analyzed in order to investigate natural frequency and maximum displacement for 10 times. It was found that the first mode of natural frequency is 109.1Hz with the maximum displacement of 0.16mm while the tenth mode of natural frequency is 2464Hz with the maximum displacement of 0.25mm. Consequently, the results of modal analysis of the turbo-blower for a fuel cell system show good dynamic responses.

• International Journal of Precision Engineering and Manufacturing
• /
• 제3권2호
• /
• pp.61-71
• /
• 2002

This paper presents the dynamic analysis of indeterminate rotor systems with angular contact ball bearings subject to axial and radial loads. The reaction forces against applied radial loads significantly influence the dynamic characteristics of angular contact ball bearings. However, the reaction forces are hard to determine in the case of indeterminate rotor-bearing systems. To this end, this paper proposes a finite element model for indeterminate rotor systems with angular contact ball bearings. An improved bearing model is adopted which is originated from the Harris's bearing dynamic model. The bearing model is also extended to include centrifugal forces due to the ball and inner ring. This paper utilizes a new iterative algorithm for general, indeterminate rotor systems with angular contact ball bearings. This examples are provided to illustrate the dynamic characteristics of rotor systems with angular contact ball bearings subject to axial and radial loads. The experimental and numerical results prove that the proposed method is useful for the dynamic analysis of indeterminate rotor systems with angular contact ball bearings.

• Structural Engineering and Mechanics
• /
• 제42권4호
• /
• pp.471-488
• /
• 2012

An efficient one dimensional finite element model has been presented for the dynamic analysis of composite laminated beams, using the efficient layerwise zigzag theory. To meet the convergence requirements for the weak integral formulation, cubic Hermite interpolation is used for the transverse displacement ($w_0$), and linear interpolation is used for the axial displacement ($u_0$) and shear rotation (${\psi}_0$). Each node of an element has four degrees of freedom. The expressions of variationally consistent inertia, stiffness matrices and the load vector are derived in closed form using exact integration. The formulation is validated by comparing the results with the 2D-FE results for composite symmetric and sandwich beams with various end conditions. The employed finite element model is free of shear locking. The present zigzag finite element results for natural frequencies, mode shapes of cantilever and clamped-clamped beams are obtained with a one-dimensional finite element codes developed in MATLAB. These 1D-FE results for cantilever and clamped beams are compared with the 2D-FE results obtained using ABAQUS to show the accuracy of the developed MATLAB code, for zigzag theory for these boundary conditions. This comparison establishes the accuracy of zigzag finite element analysis for dynamic response under given boundary conditions.

• 한국소음진동공학회논문집
• /
• 제15권6호
• /
• pp.667-673
• /
• 2005

This paper shows a method for design of the nano-positioning planar scanner used in the scanning probe microscope. The planar scanner is composed of flexure guides, piezoelectric actuators and feedback sensors. In the design of flexure guides, the Castigliano's theorem was used to find the stiffness of the guide. The motion amplifying mechanism was used in the piezoelectric actuator to achieve a large travel range. We found theoretically the travel range of the total system and verified using the commercial FEM(finite element method) program. The maximum travel range of the planar scanner is above than 140 $\mu$m. The 3 axis positioning capability was verified by the mode analysis using the FEM program.

• 소성∙가공
• /
• 제10권3호
• /
• pp.206-213
• /
• 2001

Dynamic deformation of metallic materials mostly accompanies substantial amounts of deformation heat. Since the flow stress of deformation is sensitive to temperature, implication of heat due to plastic work is essential to the evaluation of constitutive relations. In this study, a series of compression tests were conducted for SAF 2507 super duplex stainless steel at various temperatures and strain rates. The accumulation of plastic work was calculated through numerical integration and converted into the elevation of temperature. Subsequent logarithmic interpolation deduced isothermal flow surfaces, which were primary input data of finite element analysis. Simple closed die forging process was analyzed and optimized with commercial FEM code applying both raw and calibrated material database. The effect of accounting deformation heat was more noticeable in high-speed forming process.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1989년도 가을 학술발표회 논문집
• /
• pp.19-24
• /
• 1989

The current load combination criteria for design of nuclear power plant structures are not based on the probability-based design concept but rely on the conventional design concept. In this paper, a load combination criteria for design of NPP coin-tainment structures are proposed based on a FEM-based random vibration analysis. More accurate reliability analyses under various dynamic loads such as earthquake loads were made possible by incorporating the FEM and random vibration theory, which is different from the conventional reliability analysis method. In this paper, the load factors for the design of NPP structures in Korea are proposed by considering appropriate fond combination criteria for design.