• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.3
• /
• pp.496-501
• /
• 2009

Interior Permanent Magnet Synchronous Motor (IPMSM) produces two kind of torque that Magnetic and Reluctance torque. The permanent magnet linkage flux ${\Psi}_a$ and d-axis and q-axis inductances have an important influence on the torque characteristic of IPMSM. Thus their accurate prediction is essential for predicting performance aspect such as the torque and flux-weakening capabilities. In this paper, the influence of barrier width on the ${\Psi}_a$ and $L_d$, $L_q$ is calculated by FEM analysis. Predictions are validated by comparison the average torques, using Maxwell Stress Tensor method.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.1
• /
• pp.48-56
• /
• 2007

In this paper, the rotor losses in high-speed permanent synchronous motor (PMSM) considering the operating condition are discussed. In order to maintain the mechanical integrity of a high-speed permanent magnet machine rotor intended for high-speed operation, the rotor assembly is often retained within a stainless steel or Carbon-Fiber/Epoxy sleeve. The sleeve is exposed to fields produced by the stator from either the slotting or the mmf harmonics that are not synchronous with rotor losses. On the basis of analytical field analysis, the rotor losses are analyzed. In particular, the no-load, rated with air-cooled, and forced water cooled conditions are considered. The results are validated extensively by comparison with non-linear finite element method (FEM).

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.5
• /
• pp.860-868
• /
• 2007

In this paper. design of spoke type BLDC motor which have a characteristics of concentrating fluxes and relatively high reluctance torque among IPM BLDC motors has been researched. To reduce cogging torque and torque ripple. rotor pole shape of optimal design is proposed. To clearly see the effects due to the changed rotor pole shape. magnetic circuit model. 2D FEM and design of experiments (DOE) are used. Then considering these results proper rotor pole shape which have an good effect on air gap flux density and cogging torque. back-emf is designed. Moreover. the validity of proposed model in this paper is also verified by comparison between gained experiment and analysis data.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.5
• /
• pp.612-619
• /
• 2013

This paper proposes an early diagnosis technique for the stator-turn fault (STF) in an interior permanent magnet (IPM)-type brushless DC (BLDC) motor using the impedance parameter. We have analyzed the varying characteristics owing to the STF through various experiments and the finite element method (FEM). As a result, we have presented a simple method for fault detection. This technique can be applied without requiring a fast Fourier transform (FFT) and the calculation of the negative-sequence impedance. The fault detection system works on the basis of the comparison the measured impedance with the database impedance. The variations in the characteristics owing to the STF as well as the proposed technique have been verified through the simulation and experiment.

• Wind and Structures
• /
• v.5 no.2_3_4
• /
• pp.257-266
• /
• 2002

In the recent years flow around bridges are investigated using computer modeling. Selvam (1998), Selvam and Bosch (1999), Frandsen and McRobie (1999) used finite element procedures. Larsen and Walther (1997) used discrete vorticity procedure. The aeroelastic instability is a major criterion to be checked for long span bridges. If the wind speed experienced by a bridge is greater than the critical wind speed for flutter, then the bridge fails due to aeroelastic instability. Larsen and Walther (1997) computed the critical velocity for flutter using discrete vortex method similar to wind tunnel procedures. In this work, the critical velocity for flutter will be calculated directly (free oscillation procedure) similar to the approaches reported by Selvam et al. (1998). It is expected that the computational time required to compute the critical velocity using this approach may be much shorter than the traditional approach. The computed critical flutter velocity of 69 m/s is in reasonable comparison with wind tunnel measurement. The no flutter and flutter conditions are illustrated using the bridge response in time.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.752-755
• /
• 2001

In order to investigate the vibration characteristics of fluid-structure interaction problem, we modeled two rectangular identical plates coupled with bounded fluid. The fixed boundary condition along the plate edges and an ideal fluid are assumed. MSC/NASTRAN was used to perform finite element analysis and analytic solutions were compared with experimental solutions to verify finite element model. As a result, comparison of FEM and experiment show good agreement, and the transverse vibration modes, in-phase and out of-phase, were observed alternately in the fluid-coupled system. The effect of distance between two rectangular plates on the fluid-coupled natural frequency is investigated.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.189-190
• /
• 2009

This paper studies the lateral response of reinforced concrete columns strengthened with carbon fiber reinforced polymer sheet (CFRP) subjected to static loading analytically by comparing with experimental results. For interface behavior between RC columns and CFRP, and interface element in FEM was applied and verified its performance by analyzing lateral behavior of RC columns strengthened with CFRP. The comparison shows that the proposed analytical method is effective for nonlinear analysis of RC columns strengthened CFRP.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.106-109
• /
• 2008

In this paper, impedance of the chiller foundation for ships is studied by using FEM and prediction is compared to measurements. Small and medium weight hammer are used to cover high and low frequency ranges in impedance measurements. Comparison shows that measurement and prediction is in good agreement in which coherence is higher than 0.98 for the frequency ranges of 40-50 Hz to 1600 -2000 Hz.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.3
• /
• pp.93-100
• /
• 2003

Switched reluctance motor(SRM) has some advantages such as low cost, high torque density but SRM has essentially high torque ripple due to its salient structure. In order to apply SRM to industrial field, torque ripple has to be reduced. This paper introduces optimal design process of SRM using an optimization algorithm of Progressive Quadratic Response Surface Modeling(PQRSM) and two-dimensional(2D) Finite Element Method(FEM). The electrical and geometrical design parameters have been adopted as 2D design variables. From this work, it can be obtained both the optimal design minimized torque ripple and the optima1 design maximized the average torque, respectively. Finally, this Paper Presents Performance comparison of two optimal designs and consider influence of the selected design variables in torque characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.226-227
• /
• 2008

We constructed a class I Flextensional transducer, and analyzed the variation of the resonance frequency of the transducer in relation to its design variables. We used the FEM for the analysis. Major axis length, minor axis length, thickness and material properties of the shell have large effects on the resonance frequency. In addition, the validation of the FE model was verified by manufacturing and comparison of the impedance analysis.