• Journal of Power System Engineering
• /
• v.18 no.5
• /
• pp.66-73
• /
• 2014

This study was considered to occur the local wall thinning at elbow which is flowing the steam and high-pressure water of high-temperature. The angle of elbow is ${\Theta}=45^{\circ}$ and $67.545^{\circ}$. The damage behaviors of inner or outer wall thinning elbow under internal pressure were calculated by FEA(finite element analysis). We compared the simulated results by FEA with experimental data. The FEA results are as follows: In the FEA results of three types of wall thinning ratio, the circumferential and longitudinal stresses show the similar values regardless of the angle of elbow, respectively. The circumferential strain was greater at elbow of small angle, but the longitudinal strain was nearly same. The FEM stress of outer wall thinning elbow was slightly higher than that of the inner wall thinning elbow, and strain was also slightly higher. In the experiments, the circumferential strain was increased with the increase in the internal pressure, and increased rapidly on about 0.2% of strain. The longitudinal strain was small. The strain at break was much smaller than 0.2%. In the relation between pressure and eroded ratio, the criteria that can be used safely under operating pressure and design pressure were obtained. The results of FEA were in relatively good agreement with those of the experiment.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.4
• /
• pp.419-425
• /
• 2014

This study applied finite element analysis (FEA) to the body frame of the 200-meter class multi-legged subsea walking robot known as Crabster (CR200). The body frame of the CR200 is modeled after the ribcage of a human so that it can disperse applied external loads. It is made of carbon-fiber-reinforced plastic (CFRP). Therefore, the frame is lighter and stronger than it would be if it were made of other conventional materials. In order to perform FEA for the CFRP body frame, we applied the material properties of the CFRP as obtained from a specimen test to an FE model of CFRP frame. Finally, we performed FEA with respect to the load conditions encountered when the robot is launched into and recovered from the sea. Also, we performed FEA for the frame, assuming that it was fabricated using a conventional material, in order to compare its characteristics with CFRP.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.2
• /
• pp.204-217
• /
• 2016

Modified poplar has emerged as a potential raw material for furniture production. Lack of specific modified poplar strength information; however, restricts applications in the furniture industry especially as related to strength in corner-joints. Optimization of strength in L-shaped corner dowel modified poplar joints under compression loads utilizing finite element analysis (FEA) by Taguchi method with the focus of this study. Four experiment factors (i.e., Structure Style, Tenon Length, Tenon Diameter, and Tenon Gap), each at three levels, were conducted by adopting a $L_9-3^4$ Taguchi orthodoxy array (OA) to determine the optimal combination of factors and levels for the von Mises stress utilizing ANSYS software. Results of Signal-to-Noise ratio (S/N) analysis and the analysis of variance (ANOVA) revealed the optimal L-shaped corner dowel joint in modified poplar is $45^{\circ}$ Bevel Butt in structure style, 24 mm in tenon length, 6 mm in tenon diameter, and 20 mm in tenon gap. Tenon length and tenon gap are determined to be significant design factors for affecting von Mises Stress. Confirmation tests with optimal levels and experimental test indicated the predicted optimal condition is comparable to the actual experimental optimal condition.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.2 no.4
• /
• pp.217-222
• /
• 2010

Since 1980's, optimum design techniques for ship structural design have been developed to the preliminary design which aims at minimum weight or minimum cost design of mid-ship section based on analytic structural analysis. But the optimum structural design researches about the application for the detail design of local structure based on FEA have been still insufficient. This paper presents optimization technique for the detail design of a racing motor boat. To improve the performance and reduce the damage of a real existing racing boat, direct structural analyses; static and non-linear transient dynamic analyses, were carried out to check the constraints of minimum weight design. As a result, it is shown that the optimum structural design of a racing boat has to be focused on reducing impulse response from pitching motion than static response because the dynamic effect is more dominant. Optimum design algorithm based on nonlinear finite element analysis for a racing motor boat was developed and coded to ANSYS, and its applicability for actual structural design was verifed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.2
• /
• pp.1-7
• /
• 2013

In this study, simulation on the powder compression forming of oilless bearing is performed and the analysis results are compared with the actual products. This study aims to examine the suitability of powder compression for bearing by using FEA(finite element analysis) before full-scale production. The lubrication state can be predicted by changing the coefficient of friction in order to get the optimal density gradient. Analysis for single and double action presses are performed and these results are compared with each other. State and process of optimal lubrication are proposed from the study result.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.230-235
• /
• 2017

When the characteristics of a linear induction motor (LIM) are analyzed using finite element analysis (FEA), it is desirable to set the voltage source as an input. If the voltage source is set as an input in FEA, the leakage inductance and primary resistance of the equivalent circuit must be entered by direct calculation, and the magnetizing inductance and secondary reaction effects are directly considered in FEA. Exact calculation is necessary because the primary winding resistance and leakage inductance directly entered will have a significant effect on the LIM output. Therefore, in this study, we accurately calculated the primary leakage inductance and analyzed the resulting LIM characteristics. We calculated the leakage inductance using an analytical equation and FEA, and we confirmed the accuracy by comparing the results with the value experimentally calculated using a manufactured model. We also analyzed the instrument performance and thrust of the LIM as a function of the difference in the leakage inductance. Finally, we present the conclusions on the precise analysis based on the calculation of the leakage inductance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.12
• /
• pp.8812-8819
• /
• 2015

In a situation in which importance of rail fastening system is growing with increasing the construction of concrete track, an accident of tension clamp(the component of rail fastening system) breaking has been recently occurred. This results from various factors such as field condition, operating agency, running condition, traffic frequency and so on. Thus, the study for the behavior of tension clamp is required. In this paper, an experiment and finite element analysis(FEA) have been performed to analyse the mechanical behavior of tension clamp. The stress and displacement of tension clamp have been analyzed as the clamping force through a laboratory test, and they were compared with FEA results. Furthermore, the stress and displacement of the tension clamp are derived from train load condition applying the verified model, and the fatigue vulnerability of the tension clamp is identified through stress analysis.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.2
• /
• pp.69-75
• /
• 2006

This paper deals with the optimum design solution on reduction of torque ripple for a Synchronous Reluctance Motor with concentrated winding using response surface methodology. The coupled Finite Elements Analysis (FEA) & Preisach model have been used to evaluate the nonlinear solution. Comparisons are given with characteristics of a SynRM according to the stator winding, slot number, open width of slot, slot depth, teeth width variation in concentrated winding SynRM, respectively. This paper presents an optimization procedure using Response Surface Methodology (RSM) to determine design parameters for reducing torque ripple. RSM has been achieved to use the experimental design method in combination with finite Element Method (FEM) and well adapted to make analytical model for a complex problem considering a lot of interaction of design variables. Moreover, Sequential Quadratic Problem (SQP) method is used to solve the resulting of constrained nonlinear optimization problem.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.1
• /
• pp.51-56
• /
• 2003

A custom application system, which was based on the finite element analysis, for stress on the head-skirt junction of a hot pressure vessel was developed. This is useful computer-based analysis system which designed to provide an analysis technique and knowledge conveniently available to other people. It was found the evaluation of thermal stress of several typed skirt joint of a pressure vessel could be performed early using this system.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.12
• /
• pp.789-796
• /
• 2000

This paper deals with magnetic field and characteristic analysis for ring type slotless synchronous motors by using analytical method. Since magnetic air-gap in the slotless motors is much larger than mechanical air-gap, it is necessary to analyze the magnetic flux distribution at the whole magnetic airgap region. therefore, this paper analyzes the duplicated magnetic field derived by both Permanent Magnet(PM) and armature current and estimates the back electromotive force and torque characteristic by subdividing the conductor region. The analysis results are verified by comparing with Finite Element Analysis(FEA) results.