• Korean Journal of Materials Research
• /
• v.22 no.7
• /
• pp.346-351
• /
• 2012

$Li_{1+x}Al_xTi_{2-x}(PO_4)_3$(LATP) is a promising solid electrolyte for all-solid-state Li ion batteries. In this study, LATP is prepared through a sol-gel method using relatively the inexpensive reagents $TiCl_4$. The thermal behavior, structural characteristics, fractured surface morphology, ion conductivity, and activation energy of the LATP sintered bodies are investigated by TG-DTA, X-ray diffraction, FE-SEM, and by an impedance method. A gelation powder was calcined at $500^{\circ}C$. A single crystalline phase of the $LiTi_2(PO_4)_3$(LTP) system was obtained at a calcination temperature above $650^{\circ}C$. The obtained powder was pelletized and sintered at $900^{\circ}C$ and $1000^{\circ}C$. The LTP sintered at $900{\sim}1000^{\circ}C$ for 6 h had a relatively low apparent density of 75~80%. The LATP(x = 0.3) pellet sintered at $900^{\circ}C$ for 6 h was denser than those sintered under other conditions and showed the highest ion conductivity of $4.50{\times}10^{-5}$ S/cm at room temperature. However, the ion conductivity of LATP (x = 0.3) sintered at $1000^{\circ}C$ decreased to $1.81{\times}10^{-5}$ S/cm, leading to Li volatilization and abnormal grain growth. For LATP sintered at $900^{\circ}C$ for 6 h, x = 0.3 shows the lowest activation energy of 0.42 eV in the temperature range of room temperature to $300^{\circ}C$.

• Korean Journal of Food Science and Technology
• /
• v.48 no.1
• /
• pp.92-95
• /
• 2016

Ultra-high pressure (UHP) was applied to glutinous rice (Dongjin) and brown rice (Shindongjin) to determine its effects on the textural characteristics of cooked rice and bacterial reduction in uncooked rice. Hardness and stickiness of the cooked glutinous and brown rice pretreated with 500 MPa for 5 min were significantly attenuated compared to that of the control rice (p<0.05). After the UHP treatment, particles of the glutinous and brown rice were observed to be finer when cross sections of the rice were analyzed using field emission scanning electron microscope. The total bacterial count in the brown rice treated with 600 MPa for 5 min was reduced from $10^7CFU/g$ to $10^4CFU/g$, while the number of thermoduric bacteria in the brown rice was not significantly different after the UHP treatment. These results suggest that UHP may be an effective method for improving texture of dried rice and to reduce bacterial count in raw rice.

• Restorative Dentistry and Endodontics
• /
• v.36 no.1
• /
• pp.50-58
• /
• 2011

Objectives: The purpose of this study was to compare the microshear bond strength (uSBS) of two totaletch and four self-etch adhesive systems and a flowable resin to enamel. Materials and Methods: Enamels of sixty human molars were used. They were divided into one of six equal groups (n = 10) by adhesives used; OS group (One-Step Plus), SB group (Single Bond), CE group (Clearfil SE Bond), TY group (Tyrian SPE/One-Step Plus), AP group (Adper Prompt L-Pop) and GB group (G-Bond). After enamel surfaces were treated with six adhesive systems, a flowable composite resin (Filek Z 350) was bonded to enamel surface using Tygon tubes. the bonded specimens were subjected to uSBS testing and the failure modes of each group were observed under FE-SEM. Results: 1. The uSBS of SB group was statistically higher than that of all other groups, and the uSBS of OS, SE and AP group was statistically higher than that of TY and GB group (p < 0.05). 2. The uSBS for TY group was statistically higher than that for GB group (p < 0.05). 3. Adhesive failures in TY and GB group and mixed failures in SB group and SE group were often analysed. One cohesive failure was observed in OS, SB, SE and AP group, respectively. Conclusions: Although adhesives using the same step were applied the enamel surface, the uSBS of a flowable resin to enamel was different.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.169-169
• /
• 2010

As display industry requires various applications for future display technology, which can guarantees high level of flexibility and transparency on display panel, oxide semiconductor materials are regarded as one of the best candidates. $InGaZnO_4$(IGZO) has gathered much attention as a post-transition metal oxide used in active layer in thin-film transistor. Due to its high mobility fabricated at low temperature fabrication process, which is proper for application to display backplanes and use in flexible and/or transparent electronics. Electrical performance of amorphous oxide semiconductors depends on the resistance of the interface between source/drain metal contact and active layer. It is also affected by sheet resistance on IGZO thin film. Controlling contact/sheet resistance has been a hot issue for improving electrical properties of AOS(Amorphous oxide semiconductor). To overcome this problem, post-annealing has been introduced. In other words, through post-annealing process, saturation mobility, on/off ratio, drain current of the device all increase. In this research, we studied on the relation between device's resistance and post-annealing temperature. So far as many post-annealing effects have been reported, this research especially analyzed the change of electrical properties by increasing post-annealing temperature. We fabricated 6 main samples. After a-IGZO deposition, Samples were post-annealed in 5 different temperatures; as-deposited, $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$, $400^{\circ}C$ and $500^{\circ}C$. Metal deposition was done on these samples by using Mo through E-beam evaporation. For analysis, three analysis methods were used; IV-characteristics by probe station, surface roughness by AFM, metal oxidation by FE-SEM. Experimental results say that contact resistance increased because of the metal oxidation on metal contact and rough surface of a-IGZO layer. we can suggest some of the possible solutions to overcome resistance effect for the improvement of TFT electrical performances.

• Korean Journal of Dental Materials
• /
• v.43 no.4
• /
• pp.343-349
• /
• 2016

This experiment was carried out to examine whether the post-firing heat treatment is effective in increasing the hardness of metal-ceramic alloy of the Pd-Au-Ag-Sn system. Precipitation hardening by holding at $600^{\circ}C$ after simulated complete porcelain firing in a metal-ceramic alloy of the Pd-Au-Ag-Sn system was examined by observing the change in hardness, crystal structure, and microstructure using a hardness test, X-ray diffraction (XRD), and field emission scanning electron microscopy (FE-SEM). The hardness of the alloy increased apparently by holding the specimen at $600^{\circ}C$ for 30 min after simulated complete porcelain firing. The formation of fine grain interior precipitates during holding at $600^{\circ}C$ caused the formation of lattice strain in the grain interior, resulting in apparent hardening. The faster cooling rate (stage 0) during simulated complete porcelain firing resulted in more effective precipitation hardening during holding at $600^{\circ}C$. From the above results, an appropriate post-firing heat treatment, such as holding at $600^{\circ}C$ for 30 min after complete porcelain firing may increase the durability of metal-ceramic prostheses composed of Pd-Au-Ag-Sn alloy.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.197-197
• /
• 2019

총인처리시설에서는 응집제를 주입하여 인이나 오염물질을 침전시켜 처리하고 있으며 PAC(poly aluminum chloride)나 $FeCl_3$, $Al_2(SO_4)_3$, 등 다양한 종류의 응집제가 사용되어지고 있다. 하지만 기존에 사용되어 지고 있는 알루미늄계열의 응집제는 처리수에 잔류이온이 존재하게 되어 인체에 축적돼 알츠하이머 병 등 신체질환을 유발할 수 있는 단점이 있다. 따라서 이러한 단점을 사전에 예방하기 위해 $TiCl_4$와 같은 티타늄계열 응집제에 대한 연구가 진행되고 있다. $TiCl_4$ 응집제는 인 제거에 효과적으로 적용할 수 있으며 수중에 잔류이온을 유발하지 않으며 Ti이온은 치과임플란트나 의료장비로 사용될 만큼 인체에 무해하다고 알려져 있다. 응집제 사용에 따라 생성된 응집슬러지의 처리방안에 있어서 기존 응집제의 경우 생성된 슬러지의 대부분은 하수슬러지 위탁처리업체를 통해 소각 및 매립, 재활용 되고 있으나, $TiCl_4$를 응집제로 사용할 경우 생성된 슬러지를 인발하여 건조 및 소성을 통해 이산화티타늄으로 재활용할 수 있어 슬러지를 친환경적으로 처리가 가능해 기존 슬러지 처리방안의 경제적, 환경적 부담을 줄일 수 있는 장점이 있다. 따라서 본 연구에서는 $TiCl_4$를 하수처리장 방류수에 주입하여 수중의 총인(T-P)을 처리한 후 생성된 슬러지를 인발하여 건조와 소성과정을 거쳐 이산화티타늄을 제조하였다. 방류수를 취수해 2.5mg/L의 초기 총인 농도를 가진 원수를 제조하였으며 제조된 원수에 $TiCl_4$를 0.6mL 주입하였을 때 99.93%의 총인제거효율을 얻을 수 있었다. 응집 실험 후 생성된 슬러지를 인발하여 건조 후 $300{\sim}1000^{\circ}C$의 각각 다른 온도조건에서 소성하여 이산화티타늄을 제조하였으며, SEM과 XRD를 통해 제조된 이산화티타늄의 표면특성과 결정성 분석을 실시하였다. 제조된 이산화티타늄은 $500{\sim}800^{\circ}C$에서는 아나타제, $900{\sim}1000^{\circ}C$에서는 루타일 결정구조가 나타났다. 또한, $TiCl_4$ 주입량에 따른 이산화티타늄의 최종 생산량과 제조 시 사용되는 건조로 및 소성로의 경제적 비용 등을 고려하여 이산화티타늄 1Ton을 제조하기 위해 필요한 단가를 산출하였다. 본 연구에서 제조된 이산화티타늄 1kg의 생산단가는 약 5,400원으로 나타났으며, 가장 많이 사용되는 P-25 광촉매 보다 저렴한 가격으로 제조 및 판매를 기대할 수 있다. 따라서 하수처리장에 적용 시 기존 응집제 보다 비싼 $TiCl_4$ 비용을 보완하고 친환경적인 슬러지 처리로 제조된 이산화티타늄의 유통 및 현장적용을 통해 경제적, 환경적으로 우수하다고 판단된다.

• Korean Journal of Soil Science and Fertilizer
• /
• v.48 no.5
• /
• pp.332-339
• /
• 2015

The objective of this study was to evaluate the effectiveness of different biochars on the removal of heavy metals from aqueous media. The experiment was carried out in aqueous solutions containing $200mg\;CdL^{-1}$ or $200mg\;PbL^{-1}$ using two different biochars derived from soybean stover and orange peel (20 mg Cd or $Pbg^{-1}$ biochar). After shaking for 24 hours, biochars were filtered out, and Cd and Pb in the filtrate were analyzed by flame atomic absorption spectrophotometer (FAAS). In order to provide information regarding metal binding strength on biochars, sequential extraction was performed by modified SM&T (formerly BCR). The results showed that 70~100% of initially added Cd and Pb was adsorbed on biochars and removed from aqueous solution. The removal rate of Pb (95%, 100%) was higher than that of Cd (70%, 91%). In the case of Cd, orange peel derived biochar (91%) showed higher adsorption rate than soybean stover derived biochar (70%). Cd was adsorbed on the biochar mainly in exchangeable and carbonates fraction (1st phase). In contrast, Pb was adsorbed on it mainly in the form of Fe-Mn oxides and residual fraction (2nd and 4th phase). The existence of Cd and Pb as a form of surface-precipitated complex was also observed on the surfaces of biochars detected by field emission scanning electron microscope (FESEM) and energy dispersive X-ray spectrometer (EDAX).

• Nuclear Engineering and Technology
• /
• v.52 no.12
• /
• pp.2860-2866
• /
• 2020

Oxide dispersion-strengthened materials W-1wt%Pr₂O₃ and W-1wt%La₂O₃ were synthesized by wet chemical method and spark plasma sintering. The field emission scanning electron microscopy (FE-SEM) analysis, XRD and Vickers microhardness measurements were conducted to characterize the samples. The irradiations were carried out with a 5 keV helium ion beam to fluences up to 5.0 × 10²¹ ions/m² under 600 ℃ using the low-energy ion irradiation system. Transmission electron microscopy (TEM) study was performed to investigate the microstructural evolution in W-1wt%Pr₂O₃ and W-1wt%La₂O₃. At 1.0 × 10²⁰ He⁺/m², the average loops size of the W-1wt%Pr₂O₃ was 4.3 nm, much lower than W-1wt% La₂O₃ of 8.5 nm. However, helium bubbles were not observed throughout in both doped W materials. The effects of pre-irradiation with 1.0 × 10²¹ He⁺/m² on trapping of injected deuterium in doped W was studied by thermal desorption spectrometry (TDS) technique using quadrupole mass spectrometer. Compared with the samples without He⁺ pre-irradiation, deuterium (D) retention of doped W materials increased after He⁺ irradiation, whose retention was unsaturated at the damage level of 1.0 × 10²²D₂⁺/m². The present results implied that irradiation effect of He⁺ ions must be taken into account to evaluate the deuterium retention in fusion material applications.

• Korean Journal of Materials Research
• /
• v.28 no.12
• /
• pp.763-768
• /
• 2018

In this study, glass fibers are fabricated via a continuous spinning process using manganese slag, steel slag, and silica stone. To fabricate the glass fibers, raw materials are put into an alumina crucible, melted at $1550^{\circ}C$ for 2 hrs, and then annealed at $600^{\circ}C$ for 2 hrs. We obtain a black colored glass. We identify the non-crystalline nature of the glass using an XRD(x-ray diffractometer) graph. An adaptable temperature for spinning of the bulk marble glass is characterized using a high temperature viscometer. Spinning is carried out using direct melting spinning equipment as a function of the fiberizing temperature in the range of $1109^{\circ}C$ to $1166^{\circ}C$, while the winder speed is in the range of 100rpm to 250rpm. We investigate the various properties of glass fibers. The average diameters of the glass fibers are measured by optical microscope and FE-SEM. The average diameter of the glass fibers is $73{\mu}m$ at 100rpm, $65{\mu}m$ at 150rpm, $55{\mu}m$ at 200rpm, and $45{\mu}m$ at 250rpm. The mechanical properties of the fibers are confirmed using a UTM(Universal materials testing machine). The average tensile strength of the glass fibers is 21MPa at 100rpm, 31MPa at 150rpm, 34MPa at 200rpm, and 45MPa at 250rpm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.458-463
• /
• 2019

Palladium (Pd) is widely used as a catalyst and noxious gas sensing materials. Especially, various researches of Pd based hydrogen gas sensor have been studied due to the noble property, Pd can be adsorbed hydrogen up to 900 times its own volume. In this study, palladium oxide (PdO) nanostructures were grown on Si substrate ($SiO_2(300nm)/Si$) for 3 to 5 hours at $230^{\circ}C{\sim}440^{\circ}C$ using thermal chemical vapor deposition system. Pd powder (source material) was vaporized at $950^{\circ}C$ and high purity Ar gas (carrier gas) was flown with the 200 sccm. The surface morphology of as-grown PdO nanostructures were characterized by field-emission scanning electron microscopy(FE-SEM). The crystallographic properties were confirmed by Raman spectroscopy. As the results, the as-grown nanostructures exhibit PdO phase. The nano-cube structures of PdO were synthesized at specific substrate temperatures and specific growth duration. Especially, PdO nano-cube structrures were uniformly grown at $370^{\circ}C$ for growth duration of 5 hours. The PdO nano-cube structures are attributed to vapor-liquid-solid process. The nano-cube structures of PdO on graphene nanosheet can be applied to fabricate of high sensitivity hydrogen gas sensor.