• Korean Chemical Engineering Research
• /
• v.52 no.5
• /
• pp.667-671
• /
• 2014

In this study, we suggest a facile method to control conditions of single component independently when preparing consisting two-component metal oxides nanofiber by simply dispersing nanoparticles in precursor solution. The well dispersed $SiO_2$ nanoparticles in $TiO_2$ nanofibers were successfully synthesized through a simple electrospinning process. The as-synthesized nanodfibers were investigated via FE-SEM, XRD and EDS for structural studies, furthermore, the analysis of UV-VIS and photocatalytic activity were carried out for demonstrate the effect of $SiO_2$ nanoparticles dispersed in $TiO_2$ nanofibers. As a result, $TiO_2$ nanofibres dispersed with $SiO_2$ nanoparticles have enhanced photocatalytic activity than that of $TiO_2$ nanofibres only. In this strategy, the introduction of $SiO_2$ nanoparticles in $TiO_2$ nanofibers were attribute to enlarge absorption in the visible region (380~440 nm). Additionally, $Br{\o}nsted$ acid sites generated in each metal oxide of Ti and Si increase OH radicals efficiently as well as it limit recombination loss by holding photogenerated electrons for high efficient photocatalytic activity.

• Journal of Radiation Protection and Research
• /
• v.39 no.1
• /
• pp.14-20
• /
• 2014

A lot of radiation exposure for radiation workers who are engaged in Nuclear Power Plants, especially PWRs, have been caused during the outage by CRUD, such as $^{58}Co$, $^{60}Co$, in Reactor Coolant System. And therefore we need to know source terms to achieve optimization of protection for the radiation workers from radiation exposure at Nuclear Power Plants efficiently. This study analyzed source terms at domestic NPPs (PWRs) nearby Steam Generator with CZT semiconductor detector using by IN-VIVO method during the outage for the first time in the country. We checked difference for the detected source terms between old and new NPP. It was performed especially to see a change of source terms by water chemistry process as well. There was not any difference by water chemistry process both NPPs. The main source terms are $^{58}Co$ and $^{60}Co$ at all NPPs. $^{59}Fe$ only appears in the new NPP. $^{137}Cs$ and $^{95}Zr$ are shown in the old NPP. The fraction of $^{58}Co/^{60}Co$ in the new NPP is higher than the old NPP for increasing the specific activity of $^{60}Co$.

• Analytical Science and Technology
• /
• v.6 no.3
• /
• pp.329-334
• /
• 1993

The formation of Mo(VI)-alizarin red S chelate ion its extraction into an organic solvent by ion-pairing for the separarive determination of trace Mo(VI) in natural water was applied in seawater samples. Removed Fe(III) and Zn(II), and Cu(II) by precipitating with anthranilic acid at pH 4.0 and 2.0, seawater 100mL was sampled in 250mL separatory funnel. After Mo(VI)-ARS chelate ion was formed by adding 0.01M alizarin red S solution 1.0mL to the water sample of pH 4.6, 0.6% aliquat-336 chloroform solution 10mL was added and the solution was vigorously shaked for about 30 seconds to form the ion-pair between Mo(VI)-ARS and aliquat-336 perfectly. The solution was stood for about 30 minutes. And the organic phase was taken for the absorbance measurement of the ion-pair at 520nm. The content of Mo(VI) was obtained from the standard calibration curve. Several extraction conditions such as pH, adding amounts of alizarin red S and aliquat-336, and shaking and standing times were optimized and the interferences and release of concomitant ions was also studied. This procedure was applied to the analysis of Eastern and Yellow seawaters. It could be confirmed from the recoveries of over 85% in samples spiked with a given amount of Mo(VI) that this method was also quantitative in the determination of trace Mo(VI) in a seawater.

• Journal of the Korean Ceramic Society
• /
• v.42 no.4
• /
• pp.269-275
• /
• 2005

We analyzed the unit cell performance against the cathode porosity, which is supposed to be closely related with active sites for the cathode reaction. In order to fabricate the unit cells with different porosity in the cathode layer we changed the mixing ratio of fine and coarse LSCF cathode powders. The final porosity of each cathode layer was 14, 23, 27, $39\%$ respectively. According to the electrochemical analysis of unit cell performance via DC current interruption and AC impedance method, the electrodic polarization resistance was diminished as the cathode porosity increased. The decrease of polarization resistance was attributed due to the increase of active reaction sites and the enhancement of overall unit cell performance could be explained in the same line.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.11
• /
• pp.259-272
• /
• 2019

Steel-concrete single-leaf blast-resistant doors are protective structures consisting of a steel box and reinforced concrete slab. By the domestic blast-resistant doors, the structure is not designed efficiently because few studies have examined the effects of variables, such as the blast pressure, rebar ratio, and steel plate thickness on the structural behavior. In this study, the structural behavior of the doors was analyzed using the FE method, and the support rotation and ductility ratio used to classify the structural performance were reviewed. The results showed that the deflection changes more significantly when the plate thickness increases than when the rebar spacing is a variable. This is because the strain energy absorbed by the door is reduced considerably when the plate thickness increases, and as a result, the maximum deflection becomes smaller. According to a comparison of the calculated values of the support rotation and the ductility ratio, the structural performance of the doors could be classified based on the support rotation of one degree and ductility ratio of three. On the other hand, more explosion tests and analytical studies will be needed to classify the damage level.

• Applied Biological Chemistry
• /
• v.18 no.3
• /
• pp.177-182
• /
• 1975

The analysis of Jerusalem artichoke showed that it contains 12.09% of Inulin. The results obtained from the examination of the conditions for fructose production by cultivating Pencillum sp 1 in the Jerusalem articoke medium were as follows: 1. The optimum amount of water added to Jerusalem artichoke was 2.5 $\ell$ of distilled water per ㎏ of fresh Jerusalem artichoke. It this case, the concentration of Inulin was 4% (w/v). 2. The optimum temperature was $30^{\circ}C$, the initial optimum pH was 5.0 and the optimum cultural period was 72 hours. 3. Shaking culture with 50 ml of the medium and 120 oscills/min in 500 ml shaking flask was most effective as the culture method. 4. 0.1% of $NH_4H_2PO_4$ as a nitrogen source, 0.001 of $FeSO_47H_20$ and 0.001% of $MgSO_47H_2$ as metal salts were most effective. 5. Fructose production continued to increase for 72 hours under the optimum conditions for cultivation and the highest production rate to the Inulin was 95.25%.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.247-253
• /
• 1996

Microscopic analysis has been performed in order to investigate effects of the microstructure of the starting feed rods on the morphology of the S-L interface and the stability of the molten zone during single crystal growth of $SrTiO_{3}$ using a floating zone method. Undoped and $Fe_{2}O_{3}$ doped $SrTiO_{3}$ doped $SrTiO_{3}$ specimens, sintered at the different temperatures have been used. In the case of the feed rods sintered at the lower temperature($1400^{\circ}C$), the poor densification made the stability of the molten zone difficult to maintain. The feed rods sintered at the higher temperature ($1600^{\circ}C$) exhibited the higher density but their molten zone was difficult to maintain due to the presence of the abnormally grown grains. It is concluded that the uniform grain size distribution of the feed rod is the critical factor to maintain the stable molten zone and therefore to give optimum growth condition during FZ single crystal growth.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.46 no.3
• /
• pp.219-229
• /
• 2020

Recently, since atopic dermatitis is sensitive to skin irritation, it has been suggested that the development of a patch that can effectively exhibit adhesion and absorption to a specific local area while minimizing skin irritation, and capable of appropriate drug release should be given priority. In this study, we tried to develop a hydrogel patch that minimizes skin irritation, adheres effectively to a specific area, and promotes absorption. The atopic patch was formulated into a super-absorbent hydrogel sheet using a freeze drying method. Cell viability assay was carried out using keratinocytes (HaCaT cell) and fibroblasts (L929 cells). In order to investigate the physical properties, FT-IR, FE-SEM, porosity analysis and swelling behavior were investigated. As a result, the newly prepared HA-Dex hydrogel patch was verified by biocompatibility and physical evaluation. In addition, the manufactured hydrogel patch has sufficient moisture absorption capacity and can relieve itching of atopic skin, and is expected to be applied to various drug delivery products for the treatment of atopic dermatitis in the future.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.11
• /
• pp.1065-1075
• /
• 2017

In this study, high velocity impact tests along with modeling of material behavior and numerical analyses were conducted to predict the dispersion behavior of the debris resulting from a high velocity impact fracture. For the impact tests, two different materials were employed for both the projectile and the target plate - the first setup employed aluminum alloy while the second employed steel. The projectile impacts the target plate with a velocity of approximately 1 km/s were enforced to generate the impact damages in the aluminum witness plate through the fracture debris. It was confirmed that, depending on the material employed, the debris dispersion behavior as well as the dispersion radii on the witness plate varied. A numerical analysis was conducted for the same impact test conditions. The smoothed particle hydrodynamics (SPH)-finite element (FE) coupled technique was then applied to model the fracture and damage upon the debris. The experimental and numerical results for the diameters of the perforation holes in the target plate and the debris dispersion radii on the witness plate were in agreement within a 5％ error. In addition, the impact test using steel was found to be more threatening as proven by the larger debris dispersion radius.

• The Journal of the Petrological Society of Korea
• /
• v.4 no.1
• /
• pp.49-58
• /
• 1995

Staurolite-biotite-andalusite-garnet (SBAG) assemblage and its sub-assemblages (SBA and SBG) commonly occur in the Dueumri Formation near the Chunyang granite, belonging to andalusite and sillimanite zones. The occurrence of the SBAG mineral assemblage is unusual because it is univariant in the $K_2O-FeO-MgO-Al_2O_3-SiO_2-H_2O$ (KFMASH) model system. We used projection and singular value decomposition (SVD) methods to investigate the equilibrium relationship between SBAG and its sub-assemblage. The SVD modelling of single specimen containing the SBAG assemblage suggests no reaction relationship with respect to mass-balance. Thus, the SBAG assemblages are stabilized by non-KFMASH component. On the other hand, the AFM-Mn projection suggests a reaction relationship between SBAG and its sub-assemblage because they intersect each other in this composition space. The SVD modelling, however, suggests no reaction relationship between these assemblages. Thus, the SBAG assemblages are likely to be stabilized by the variation in bulk-rock composition and/or 1.1~2,. The stable occurrence of staurolite in the sillimanite zone is compatible with pressure estimates from the garnet-plagioclase-biotite-muscovite geobarometer.