• Korean Journal of Materials Research
• /
• v.14 no.7
• /
• pp.489-493
• /
• 2004

The electrical property of MMC is essentially important to some applications such as power transmission lines and cables, electronic and electrical components as well as electromagnetic shielding equipments. The behavior of electrical resistivity of $SiC_{w}/Al$ alloy composites under as-extruded and annealed conditions has been investigated within the temperature range from room temperature to $450^{\circ}C$. It can be seen that within entire temperature range, the electrical resistivity of composites was higher than that of an unreinforced matrix alloy under the same condition of either as-extrusion or annealing. The temperature dependence of both exhibited positive incline like a typical metal. The variation of electrical resistivity of an unreinforced matrix alloy with temperature from ambient temperature to $450^{\circ}C$ was nearly monotonous, while those of composites increased monotonously at low temperature and rose to a high level after about $250^{\circ}C or 275^{\circ}C$. The difference of these temperature dependences on electrical resistivity can be interpreted as qualitatively the interfaces of $SiC_{w}$ fibers and matrix, where act as nucleation sites.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.37 no.12
• /
• pp.1654-1659
• /
• 2008

The aim of this study was to compare the fermentation characteristics of tissue cultured mountain ginseng, extruded tissue cultured mountain ginseng, and root hair of red ginseng. Also, pH, acidity, brix, reducing sugar, total sugar, and alcohol were analyzed. The extrusion conditions were barrel temperature of 110 and $140^{\circ}C$ and moisture content of 25 and 35%. Fermentation temperature was $27^{\circ}C$ for 15 days and the cultivation was fixed with Saccharomyces cerevisiae, Aspergillus usamii, and Rhizopus japonicus. The results showed that pH, brix, reducing sugar content, and total sugar content of fermented broths were decreased after 5 days and then maintained steadily for the following 10 days. Acidity of final fermented broths were 1.12% (root hair of red ginseng), 1.19% (tissue cultured mountain ginseng), and $0.97{\sim}1.02%$ (extruded tissue cultured mountain ginseng), respectively. Alcohol content of final fermented broths were 3.82% (root hair of red ginseng), 0.91% (tissue cultured mountain ginseng), and $1.86{\sim}2.18%$ (extruded tissue cultured mountain ginseng). The fermentation efficiency of extruded tissue cultured mountain ginseng (barrel temperature $140^{\circ}C$, moisture content 25%) were the highest. In conclusion, the fermentation efficiency was increased by extrusion process.

• Food Science and Preservation
• /
• v.18 no.3
• /
• pp.271-278
• /
• 2011

Considering the importance of cassava as food crops in humid tropics, the effect of feed moisture (20, 25%) and barrel temperature (110, $130^{\circ}C$) on physical properties (piece density, expansion, mechanical properties, color, water solubility index, water absorption index) and pasting properties of extruded cassava starch was investigated. The feed moisture used during extrusion processing had a significant effect on extrudates SME input, specific length and piece density at (p<0.05) while effect on cross-sectional expansion index, apparent elastic modulus and breaking strength in bending shown significantly at p<0.1. Furthermore, the interaction effect of feed moisture and barrel temperature gave a significantly affected the SME input and piece density (p<0.1), specific length (p<0.05) and on redness (p<0.01). The increase in water injection rate led to increase in piece density, apparent elastic modulus, breaking strength in bending, cold peak viscosity, breakdown and final viscosity and decrease in cross-sectional expansion index and specific length. It was found that the extrusion cooking process did not affect the value of color L, color b, water solubility index and water absorption index. Thus, the results of this study can be useful to some extent in developing extruded cassava starch as human and animal feeds.

• The Korean Journal of Food And Nutrition
• /
• v.25 no.4
• /
• pp.850-854
• /
• 2012

This study is carried out in order to develop food materials for the promotion of rice consumption. In this study, we researched the physicochemical properties of extruded rice flour (ER) and gelatinization popped rice flour (GPR) by the extrusion process and by the popped method with milled rice and brown rice. The extrusion process used a couple of screw extruders. The extrusion parameter was kept constant at a feed moisture content of 25%, barrel temperature of $120^{\circ}C$ and screw speed of 400 rpm. GPR was prepared by batch popping machine after gelatinization of rice. In order to evaluate the physicochemical properties of ER and GPR, as well as the gelatinization rate, water soluble index (WSI), water adsorption index (WAI), DPPH radical scavenging activity and total dietary fiber content, the color value was carried out. The gelatinization rate was similar to 71.1~73.8%. Further, the results of WSI and WAI were increased at ER and GPR compared to the raw materials; ER was also higher than GPR. DPPH radical scavenging activity and total dietary fiber content showed a tendency to reduce after extrution and popping. As a result of the color value, the L value of ER decreased more than the raw materials, whereas GPR increased at a and b values.

• Applied Biological Chemistry
• /
• v.51 no.2
• /
• pp.114-118
• /
• 2008

Ginseng treated with several treatment conditions of various acids to search hydrolysates on the basis of increased biological activity and modified structure. In the result of acid treatment, the conversion rate of ginsenoside Rg3, Rk1 and Rg5 was highest when ginseng treated with citric acid. After added citric acid to ginseng extract, boiled at l00$^{\circ}C$ for 1 hour and add enzyme, which is examined change by time. It compared with group which did not treated acid. Two groups became difference according to enzyme but the generation rate of ginsenoside Rg3, Rk1 and Rg5 did not show difference greatly. Also, the generation rate of ginsenoside Rg3, Rk1 and Rg5 by time passes did not show difference. The generation rate of ginsenoside Rg3, Rk1 and Rg5 increased when increased acid concentration, temperature and time. We did exclusion molding to shorten treatment time. In the result of ginseng treated with citric acid of various concentrations at various temperatures as time passes by extrusion molding, the generation rate of ginsenoside Rg3, Rk1 and Rg5 was highest when ginseng treated with 3% citric acid at l60$^{\circ}C$ for 20 minutes. In addition, total saponin amount of ginseng treated with 3% citric acid at 160$^{\circ}C$ for 20 minutes was about 11% higher than ginseng heated at 120$^{\circ}C$ for 3 hours. These results indicated that our exclusion molding process more effective, compared to traditional red ginseng manufacturing process.

• Microbiology and Biotechnology Letters
• /
• v.16 no.3
• /
• pp.231-237
• /
• 1988

Several methods to produce ethanol from tapioca starch were examined. Among four methods tested, alcohol fermentation with extruded tapioca starch was the most effective, which alcohol yield was 460.5 f/ton. After 69hours reaction with Rhizopus sp. glucoamylase, 108.7mg/$m\ell$ of reducing sugar were produced from extruded tapioca and 43.8mg/$m\ell$ from raw tapioca starch. In alcohol fermentation with extruded tapioca, the high concentration of alcohol at early stage prevented bacterial contamination and the fermentation rate was increased due to the high saccharifying power of glucoamylase on the extruded starch, but extrusion temperature had no influence on the fermentability, Scanning electron microscopy showed that the extrusion process changed the structure of tapioca starch granule to more susceptible form to glucoamylase attack than the raw starch. And glucoamylase of Rhizopus sp. had stronger digestion activity on both extruded tapioca and raw tapioca starch than that of Aspergillus usamii.

• Journal of Korea Foundry Society
• /
• v.31 no.6
• /
• pp.347-353
• /
• 2011

There is thixo-extrusion to form high strength aluminum alloy. But, it is a problem that grains become grain coarsening during reheating process because the alloy was exposed at high temperature. In order to solve grain growth during reheating process, calcium was added in Al-Zn-Mg alloys. Primary a grain sizes of semi-solid Al-Zn-Mg-(0, 0.4, 0.6 and 0.9, wt.%)Ca were measured with image analyzer after reheating. Measured primary a grain sizes were applied to LSW(Lifshitz-Slyozov and Wagner) equation to check the effect of Ca on grain coarsening. Coarsening rate constant K values of semi-solid Al-Zn-Mg-(0, 0.4, 0.6 and 0.9, wt.%)Ca alloys were $371\;mm^3s^{-1}$, $247\;mm^3s^{-1}$, $198\;mm^3s^{-1}$ and $166 mm^3s^{-1}$, respectively. As increasing calcium content, K value decreased which means grains are refined. Also, grains of calcium addition were more spherical than that of calcium free.

• Korean Journal of Materials Research
• /
• v.9 no.5
• /
• pp.520-527
• /
• 1999

As a new approache(extrusion-sintering process) to fabricate the thermoelectric materials, it has been at tempted to extrude and sinter the powders simultaneously. It was possible to produce the highly dense <$(Bi,Sb)_2(Te,Se)_3$-based thermoelectrics with sound surface appearances and microstructures by adjusting the process variables. For the p-type materials, the Seeback coefficient was increased with the amount of Te dopants, and the thermoelectric figure of merit appeared to be $2.5\times10^{-3}/K$ at room temperature when doped with 3 at % Te. The n-type specimen doped with 0.16 mol% $SbI_3$ showed the thermoelectric figure of merit of $1.8\times10^{-3}/K$. In both p-type an 우-type materials, the carrier mobility an the thermoelectric figure of merit parallel to the extrusion direction were higher than those perpendicular to it.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.12
• /
• pp.1675-1682
• /
• 2012

Weight reduction is increasingly being considered very important in light of air pollution and the exhaustion of resources. As a result, many automotive components are being replaced by Al and Mg alloys, and studies are increasingly focusing on the same. However, the use of Mg alloys is limited because they have higher material cost and lower productivity owing to the difficult forming conditions compared with Al alloys. In this study, the tube extrusion process conditions of an automotive bumper back beam were analyzed using FEA. Material tests were performed to determine the properties, and experiments and analyses for a simple shape were performed to define the data for heat generation during plastic deformation. Then, the analyses of the product were carried out by considering various temperatures and ram speeds. The conditions were then established, and a product without surface defects was extruded successfully.

• Korean Journal of Medicinal Crop Science
• /
• v.26 no.5
• /
• pp.417-429
• /
• 2018

Background: The objective of this study was to make colloidal dispersions of the active compounds of radix of Angelica gigas Nakai that could be charaterized as nano-composites using hot melt extrusion (HME). Food grade hydrophilic polymer matrices were used to disperse these compound in aqueous media. Methods and Results: Extrudate solid formulations (ESFs) mediated by various HPMCs (hydroxypropyl methylcelluloses) and Na-Alg polymers made from ultrafine powder of the radix of Angelica gigas Nakai were developed through a physical crosslink method (HME) using an ionization agent (treatment with acetic acid) and different food grade polymers [HPMCs, such as HP55, CN40H, AN6 and sodium alignate (Na-Alg)]. X-ray powder diffraction (XRD) analysis confirmed the amorphization of crystal compounds in the HP55-mediated extrudate solid formulation (HP55-ESF). Differential scanning calorimetry (DSC) analysis indicated a lower enthalpy (${\Delta}H=10.62J/g$) of glass transition temperature (Tg) in the HP55-ESF than in the other formulations. Infrared fourier transform spectroscopy (FT-IR) revealed that new functional groups were produced in the HP55-ESF. The content of phenolic compounds, flavonoid (including decursin and decursinol angelate) content, and antioxidant activity increased by 5, 10, and 2 times in the HP55-ESF, respectively. The production of water soluble (61.5%) nano-sized (323 nm) particles was achieved in the HP55-ESF. Conclusions: Nano-composites were developed herein utilizing melt-extruded solid dispersion technology, including food grade polymer enhanced nano dispersion (< 500 nm) of active compounds from the radix of Angelica gigas Nakai with enhanced solubility and bioavailability. These nano-composites of the radix of Angelica gigas Nakai can be developed and marketed as products with high therapeutic performance.