• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.4 no.4
• /
• pp.345-352
• /
• 2006

The cemented and paraffin wastes form which are incorporated the concentrated wastes, the cemented waste form which is incorporated the spent ion-exchange resins, and the miscellaneous waste(decontamination paper) were irradiated up to $10^{+8}$ rads at $5.43{\times}10^{+5}$ rads/hr with Co-60(72,023.9 Ci) as an external irradiation source. As a result, the radiolysis gases such as $H_2,\;CH_4,\;N_2,\;C_2H_6,\;O_2,\;CO\;and\;CO_2$, were measured in all the wastes. The major gas which was generated in all the wastes was hydrogen($H_2$). The volume of the generated gases showed a difference from $0.029{\sim}0.788\;cm^3.atm/1.1g$ according to the type of wastes, and more was generated in the cemented waste form incorporated a spent ion-exchange resin than in the other wastes. More hydrogen($H_2$) gas was generated in the decontamination paper waste than in the other wastes, and the G($H_2$) value was 0.12.

• Nuclear Engineering and Technology
• /
• v.46 no.4
• /
• pp.547-556
• /
• 2014

Korea expects a shortage in storage capacity for spent fuels at reactor sites. Therefore, a need for more metal and/or concrete casks for storage systems is anticipated for either the reactor site or away from the reactor for interim storage. For the purpose of interim storage and transportation, a dual purpose metal cask that can load 21 spent fuel assemblies is being developed by Korea Radioactive Waste Management Corporation (KRMC) in Korea. At first the gamma and neutron flux for the design basis fuel were determined assuming in-core environment (the temperature, pressure, etc. of the moderator, boron, cladding, $UO_2$ pellets) in which the design basis fuel is loaded, as input data. The evaluation simulated burnup up to 45,000 MWD/MTU and decay during ten years of cooling using the SAS2H/OGIGEN-S module of the SCALE5.1 system. The results from the source term evaluation were used as input data for the final shielding evaluation utilizing the MCNP Code, which yielded the effective dose rate. The design of the cask is based on the safety requirements for normal storage conditions under 10 CFR Part 72. A radiation shielding analysis of the metal storage cask optimized for loading 21 design basis fuels was performed for two cases; one for a single cask and the other for a $2{\times}10$ cask array. For the single cask, dose rates at the external surface of the metal cask, 1m and 2m away from the cask surface, were evaluated. For the $2{\times}10$ cask array, dose rates at the center point of the array and at the center of the casks' height were evaluated. The results of the shielding analysis for the single cask show that dose rates were considerably higher at the lower side (from the bottom of the cask to the bottom of the neutron shielding) of the cask, at over 2mSv/hr at the external surface of the cask. However, this is not considered to be a significant issue since additional shielding will be installed at the storage facility. The shielding analysis results for the $2{\times}10$ cask array showed exponential decrease with distance off the sources. The controlled area boundary was calculated to be approximately 280m from the array, with a dose rate of 25mrem/yr. Actual dose rates within the controlled area boundary will be lower than 25mrem/yr, due to the decay of radioactivity of spent fuel in storage.

• Korean Journal of Microbiology
• /
• v.54 no.2
• /
• pp.105-112
• /
• 2018

To compare the denitrification efficiency, this study used molasses and methanol were used as external carbon sources. Specific experimental conditions were classified according to C/N ratio conditions. The batch test showed that the denitrification efficiency increased as C/N ratios of molasses and methanol rose. The most suitable C/N ratio of molasses turned out 4:1 considering the concentration of the residue chemical oxygen demand (COD) and the denitrification efficiency, which was 91.4%. Specific denitrification rate (SDNR) drawn as a kinetic factor demonstrated that molasses and methanol showed similar SDNR values as C/N ratios of molasses and methanol increased. Under the condition of C/N ratio 4:1, 0.0292 g $NO_3{^-}-N$ removal/g mixed liquor volatile suspended solid (MLVSS)/day (molasses), 0.0299 g $NO_3{^-}-N$ removal/g MLVSS/day (methanol) were found. Sludge adapted to molasses showed that Bacterium Pseudomonas sp. and Bergeylla sp. dominated through an analysis of microbial community. In addition, some bacteria were high convergences than the variety of microbial community. Accordingly, it was assumed that molasses focus on growing microorganisms specialized in denitrification and applied as a replaceable external carbon source that can enhance denitrification performance.

• The KIPS Transactions:PartD
• /
• v.8D no.6
• /
• pp.705-714
• /
• 2001

The computing systems of today expanded business trade and distributed business process Internet. More and more systems are developed from components with exactly reusability, independency, and portability. Component based development is focused on advanced concepts rater than passive manipulation or source code in class library. The primary component construction in CBD. However, lead to an additional cost for reconstructing the new component with CBD model. It also difficult to serve component information with rapidly and exactly, which normalization model are not established, frequency user logging in Web caused overload. A lot of difficult issues and aspects of Component Based Development have to be investigated to develop good component-based products. There is no established normalization model which will guarantee a proper treatment of components. This paper elaborates on some of those aspects of web application to adapt user requirement with exactly and rapidly. Distributed components in this paper are used in the most tiny size on network and suggest the network-addressable interface based on business domain. We also discuss the internal and external specifications for grasping component internal and external relations of user requirements to be analyzed. The specifications are stored on Servlets after dividing the information between session and entity as an EJB (Enterprise JavaBeans) that are reusable unit size in business domain. The reusable units are used in business component through query to get business component. As a major contribution, we propose a systems model for registration, auto-arrange, search, test, and download component, which covers component reusability and component customization.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.29 no.1
• /
• pp.23-33
• /
• 2011

This experimental focus to characterize luminescence properties related to CNT (Carbon Nano Tube) element dispersedly implanted in ZnS-based phosphor thin film panel fabricated by a screen printing method. More specifically FE-SEM measurements, L-V(Luminescence vs. Voltage) and photo luminescence were carried out to determine an optimum value of CNT concentration and film thickness for the thin film structure of CNT-ZnS:(Cu, Al) by the screen printing method. We confirmed that an optimum value of CNT concentration in the ZnS:(Cu, Al) film panel is about 0.75 wt% resulting that the electric conductivity is 1.6 times higher than that of pure CNT sample and showing that the luminescence intensity is increasing until the optimum concentration. Clearly, CNT is presenting in the luminescence process providing a pathway for the creation of hot electron and a channel for the electron-hole recombination but overly inserted CNT may hinder to produce the hot electron for making an avalanching process. In case of the overly doped CNT 1.0 wt% in the ZnS-based phosphor, the luminescence intensity is decreasing although the electric conductivity is exponentially increasing. Based on these results, we realized that hot electron occurred by the external electric field or exciton arose by the external photon source are reduced dramatically over the critical value of CNT concentration because CNT element provide various isolated residues in the composites of ZnS based phosphor rather than pathway or channel for the D-A(Donnor to Acceptor) pair transition or the radiative recombination of electron-hole.

• The Korean Journal of Quaternary Research
• /
• v.24 no.2
• /
• pp.1-11
• /
• 2010

Energy Balance Model (EBM) was used to experiment the distribution of surface equilibrium temperature which responds to external forcing associated with the surface characteristics. Surface equilibrium temperature is calculated as sum of incoming solar radiation and latitudinal transport is balanced with outgoing infrared radiation. To treat incoming solar radiation, the source of the earth energy, significantly for energy balance, the experiment for surface equilibrium temperature distribution was performed considering the energy balance with the latitudinal albedo change as well as land and sea distribution. In addition, linear albedo change experiment, arctic albedo 5%, 10%, 15% change experiments and the opposite albedo change experiments between arctic and mid-latitudes were performed using incoming solar radiation as an external forcing. Moreover, with and without ice-albedo feedback experiments were performed. Increasing of arctic albedo is blocked out the incoming solar radiation so that it induces decreasing of latitudinal heat transport. It is strengthened energy transport from low latitudes by keeping arctic low energy states. Therefore the temperature change in the mid-latitudes exhibits larger response than that of arctic due to the difference of transport. The land which has lower heat capacity than sea can be reach to equilibrium temperature shortly. Also land is more sensitive to temperature change with respects to albedo. Thus it induces the thermal difference between land and sea. As a result, the equilibrium temperature exhibits differently as the difference of albedo and heat capacity which are the one of surface characteristics. Surface equilibrium temperature decreases as albedo increase and the ratio of temperature change is large as heat capacity is small. The decreasing of surface equilibrium temperature with respects to increasing of linear albedo is accelerated by ice-albedo feedback. However local change of surface equilibrium temperature decreases non-linearly.

• Journal of Energy Engineering
• /
• v.25 no.2
• /
• pp.52-64
• /
• 2016

The production of nuclear energy from thorium which is non-fissile material was a main issue until the middle of 1970's, because of the thorium's abundance as energy resources, its capability of breeding fissile material U233, and the reduction of long-lived actinides. However, to use thorium as nuclear fuel, some obstacles such as the necessities of external neutron source and long-term neutron irradiation for effective breeding, and the production of high radioactive isotopes in the course of thorium breeding cycle should be overcome. The difficulties to resolve these cons of thorium cycle became the reason of interruption of the related researches in the middle of 1970's. But in the 21st century, the change of societal perspective regarding nuclear energy and the appearance of accelerator-driven nuclear reactor shift those cons into pros and rehabilitate the study of thorium. The high activity of thorium cycle turned out to be a good option as higher resistance and easier detectibility of nuclear proliferation and the employment of subcritical accelerator-driven reactor as external neutron sources is considered to enhance the nuclear safety. In this study we compare the thorium cycle with the currently-used uranium cycle and analyze the technical status and perspective of thorium researches which use accelerator-driven reactors.

• International Journal of Highway Engineering
• /
• v.15 no.6
• /
• pp.33-39
• /
• 2013

PURPOSES : This research investigates traffic noise characteristics as change the transverse rumble strips shape from rectangular to cylinder at toll plaza of highway. METHODS : The traffic noise was investigated at two different places at toll plaza of highway. One is modified grooving, another is employed cylinder shape of TRS instead of rectangular shape of TRS. A measurement of traffic noise was conducted at same location and time period. The traffic volume information was gotten from office of highway office and vehicle speed was measured by speed measuring device. The traffic noise measurement was conducted from 13:00 to 23:00 and by pass-by method. Also, the traffic noise was measured behind noise barrier. Various distance from noise barrier(7.5m, 30m, 50m) and different heights(1.2m, 3m, and 5m) were parameter for measurement of traffic noise in this study. RESULTS : The class 1 vehicle was contributed from traffic volume which was increased 1,500. However, the distribution of traffic speed didn't change compare to previous investigated period. From this study, It was found that the external traffic noise was changed as function of geometric shape of TRS. The external noise from modified grooving was less than 1.2dB(A) of the current TRS. A difference of traffic noise was 20dB(A) before and after barrier. It came from a noise barrier effect as reduction of traffic noise. According to investigate a traffic noise distribution near barrier, there is similar noise characteristic as function of height at 7.5m distance from noise barrier. Also, There is no different traffic noise between 30m and 50m from source of the noise of sound barrier. CONCLUSIONS : Based on this traffic noise investigation result, there is a clear characteristic difference as changed TRS shape. The traffic noise was reduced by changed TRS shape. Specially, traffic noise was decreased although the traffic volume was increase for same investigation time and period. It is implied that cylinder type of TRS significantly reduces the traffic noise. The specification of various TRS will be studied in the future.

• Korean Journal of Radiology
• /
• v.21 no.12
• /
• pp.1345-1354
• /
• 2020

Objective: To evaluate radiomics analysis in studies on mild cognitive impairment (MCI) and Alzheimer's disease (AD) using a radiomics quality score (RQS) system to establish a roadmap for further improvement in clinical use. Materials and Methods: PubMed MEDLINE and EMBASE were searched using the terms 'cognitive impairment' or 'Alzheimer' or 'dementia' and 'radiomic' or 'texture' or 'radiogenomic' for articles published until March 2020. From 258 articles, 26 relevant original research articles were selected. Two neuroradiologists assessed the quality of the methodology according to the RQS. Adherence rates for the following six key domains were evaluated: image protocol and reproducibility, feature reduction and validation, biologic/clinical utility, performance index, high level of evidence, and open science. Results: The hippocampus was the most frequently analyzed (46.2%) anatomical structure. Of the 26 studies, 16 (61.5%) used an open source database (14 from Alzheimer's Disease Neuroimaging Initiative and 2 from Open Access Series of Imaging Studies). The mean RQS was 3.6 out of 36 (9.9%), and the basic adherence rate was 27.6%. Only one study (3.8%) performed external validation. The adherence rate was relatively high for reporting the imaging protocol (96.2%), multiple segmentation (76.9%), discrimination statistics (69.2%), and open science and data (65.4%) but low for conducting test-retest analysis (7.7%) and biologic correlation (3.8%). None of the studies stated potential clinical utility, conducted a phantom study, performed cut-off analysis or calibration statistics, was a prospective study, or conducted cost-effectiveness analysis, resulting in a low level of evidence. Conclusion: The quality of radiomics reporting in MCI and AD studies is suboptimal. Validation is necessary using external dataset, and improvements need to be made to feature reproducibility, feature selection, clinical utility, model performance index, and pursuits of a higher level of evidence.

• Journal of the Korean Institute of Oriental Medical Informatics
• /
• v.20 no.1
• /
• pp.25-156
• /
• 2014

This thesis is consisted of studying of the medical literature about Five sense of organs. Five sense of organs are the eyes, tongue, mouth, nose and ears. Five sense of organs are performed human senses which external sensory information by accepting an important feature for maintaining the biological activity to be performed. The contents was compiled up to the Donguibogam to Chinese literature and documents encompass the Korea medical literature, Donguibogam related to the senses to identify the citation of each chapter, the actual quotation through doctrine and other publications revealed that the citation is to investigate how accurately identified through studying the analysis and observation. It is as following as I observed carefully the senses of Donguibogam quotations related to each other through doctrine and publishment institution follows in order of dynasties. There are four volumes of Han-dynasty, one volume of Weijinnanbei-Era, two volumes of Tang-dynasty, nineteen volumes of SongJinYuan-dynasty, seven volumes of Ming-dynasty as Chinese medical literature. There are four volumes of Chosun-dynasty as Korean medical literature. It is the most quotation publishment that the books of SongJinYuan-dynasty of above thirty-six-volume. It is the latest quotation book that is Gujinyigan in Chinese medical literature and Euirimchwalyo in Korean medical literature. It is very positive quotation considering even Donguibogam publishment year in 1613. The reference books are four volumes of Chosun-dynasty as Korean medical literature and thirty-two-volume of Chinese medical literature. By observing the quotation frequency, 157 times in Sheyideaiofang, 115 times in Yixuerumen, 74 times in Yixuegangmu, 39 times in Wanbinghuichun, 31 times in Euibangryuchwi, 30 times in Renzhezhizhifang and Gujinyigan, 28 times in Danxixinfafuyu, 23 times Hwangdineijing, 17 times in Nanshibizang and Yixuezhengchuan. Other else books have been cited less than 10 times. It might be made error that did not find the source of the books even though cited reference, also even though defining the source of reference it is only rare reference book. As mention above, there are a lot of discovering as the feature of reference Publications. Most of all we could find out the reference literature cited in Donguibogam, however we couldn't clarify other books in original books. Thus, we should remember that it did not coincide with cited marks when studying the Donguibogam.