• 대한조선학회논문집
• /
• 제56권2호
• /
• pp.175-186
• /
• 2019

Number of studies on the buckling of thin cylindrical pressure vessels, such as submarine pressure hull and pipe with a large ratio of diameter/thickness, have been carried out in the naval and ocean engineering. However, research about thick cylinder pressure vessel has not been active except for the specific application in nuclear area. There are not many papers for the estimation of buckling and ultimate load capacity of thick cylinders for the deep sea usage. Thus, it is important to understand the theoretical bases of the buckling and collapse process and the derivation process of such loads for the proper design and structural analysis. The objective of this study is to survey the collapse behavior, to analyse and clarify the derivation procedure and to estimate the ultimate collapse load for thick cylinder by analyzing relevant books and papers. It is found that the yielding begins at the internal surface of the thick cylinder and plasticity develops from the internal surface to the external surface to generate collapse. Also the initial imperfection of cylinder develops flattening and consequently accelerates buckling and finally ultimate collapse. By comparing the collapse loads of aluminum thick cylinder by applying equations herein, it is shown that the equations analyzed are appropriate to obtain collapse load for thick cylinder.

• Wind and Structures
• /
• 제13권5호
• /
• pp.433-449
• /
• 2010

Wind tunnel model tests were conducted for a residential apartment block located within the complex terrain of The Hong Kong University of Science and Technology (HKUST). The test building is typical of medium-rise residential buildings in Hong Kong. The model study was conducted using modelling techniques and assumptions that are commonly used to predict design wind loads and pressures for buildings sited in regions of significant topography. Results for the building model with and without the surrounding topography were compared to investigate the effects of far-field and near-field topography on wind characteristics at the test building site and wind-induced external pressure coefficients at key locations on the building facade. The study also compared the wind tunnel test results to topographic multipliers and external pressure coefficients determined from nine international design standards. Differences between the external pressure coefficients stipulated in the various standards will be exacerbated when they are combined with the respective topographic multipliers.

• 한국농공학회논문집
• /
• 제65권1호
• /
• pp.61-72
• /
• 2023

The increase in the rearing intensity of pigs has caused deterioration in the pig house's internal environment such as temperature, humidity, ammonia gas, and so on. Traditionally, the widely used method to control the internal environment was through the manipulation of the ventilation system. However, the conventional ventilation system had a limitation to control the internal environment, prevent livestock disease, save energy, and reduce odor emission. To overcome this problem, the air-recirculated ventilation system was suggested. This system has a semi-closed loop ventilation type. For designing this system, it was essential to evaluate the ventilation rates considering the pressure loss of ducts. Therefore, in this study, pressure loss calculation and experiment were conducted for the quantitative ventilation design of a semi-closed loop system. The results of the experiment showed that the inlet through which external air flows should always be opened. In addition, it was also found that for the optimum design of the semi-closed loop ventilation system, it was appropriate to install a damper or a backflow prevention device rather than a ventilation fan.

• 대한한의학회지
• /
• 제17권1호
• /
• pp.447-464
• /
• 1996

Hyperemesis gravidarum is one of the most common symptom in the early pregnancy and if it cause severe malnutrition by means of heavy vomiting as a basic sign of disease of pregnant syndrome, appropriate treatments are necessary. In the clinics the methods of treatment of hyperemesis gravidarum include herb-medication usually. But herb-medication therapy is rather difficult because during pregnancy it may cause vomiting by the smell and taste of herbs. So the author investigated the literatures referred to the external treatments of hyperemesis gravidarum excluding herb-medication and the results obtained here were as follows. 1. The external methods of treatment of hyperemesis gravidarum are various and include moxibustion, the method of applying drug at the umbilicus, ear-acupuncture method, pressure massage therapy, naso-spray method, acupoint injection, intervenous injection 2. Among the external methods of treatment of hyperemesis gravidarum , the method of applying drug at the umbilicus is most variable and almost all prescriptions use Zingiber officinalis Rose, characteristically. 3. Ear-pressure massage method to treat the hyperemesis gravidarum uses the car-acupoints of Gan, We, Shin-mun, Gyo-gam. 4. Among the external methods of treatment of hyperemesis gravidarum , moxibustion, pressure massage, and acupoint injection select frequently Nae-gwan(PC6), Chok-samni(ST36) and Chung-wan(CV12). 5. In the both the internal and external methods of treatment of hyperemesis gravidarum one have to differentiate syndromes in the viewpoint of oriental medicine and treat with the principls of treatment and prescriptions which are fit to each differentiation model under the principle of regulating the stomach and relieving vomiting.

• 한국항공우주학회지
• /
• 제50권5호
• /
• pp.297-308
• /
• 2022

극초음속 영역에서 운용되는 대부분의 극초음속 공기흡입(Air-breathing) 비행체들에 스크램제트 엔진이 탑재되고 있다. 스크램제트(Scramjet) 엔진에서는 일반적인 가스터빈 엔진의 압축기 역할을 흡입구에서 발생하는 충격파가 대신 수행하기 때문에 충격파에 의한 전압력 손실이 매우 중요하게 여겨진다. 본 연구에서는 전압력 손실을 최소화하기 위해 등엔트로피 압축면을 적용한 외부 압축형 흡입구의 설계법을 제시하고, 동일한 조건의 Busemann 흡입구와 3개의 cone 각도를 가지는 외부 압축형 흡입구를 설계하였다. 이후 전산해석을 통해 비설계 조건에 대한 성능 특성을 비교하였다. 각 흡입구 형상은 3단 외부 압축형 흡입구의 길이에 맞춰 truncation을 진행하였으며, 경계층 보정을 수행하였다. 등엔트로피 외부 압축형 흡입구는 3단 외부 압축형 흡입구에 비해 설계점에서는 우수한 성능을 보였으나 일부 비설계 조건에서는 3단 외부 압축형보다 성능이 저하되는 현상이 발생하였다.

• 대한조선학회논문집
• /
• 제44권6호
• /
• pp.666-674
• /
• 2007

It is very important to estimate static squeezing pressure distributions for lining material of sterntube after bearing at dry dock stage since the maximum squeezing pressure value can be one of the significant characteristics representing coming navigation performances of the propulsion system. Moderate oil film pressure between lining material and propulsion shaft is also essential for safe ship service. In this paper, Hertz contact theory is explained to derive static squeezing pressure. Reynolds equation simplified from Navier-Stokes equation is centrally differentiated to numerically obtain dynamic oil film pressures. New shaft alignment technology of nonlinear elastic multi-support bearing elements is also used in order to obtain external forces acting on lining material of bearing. For 300K DWT class VLCC with synthetic bush of sterntube after bearing, static squeezing pressures are calculated using derived external forces and Hertz contact theory. Optimum partial slope of the after bush is presented by parametric shaft alignment analyses. Dynamic oil film pressures are comparatively evaluated for partially bored and unbored after bush. Finally it is proved that the partial slope can drastically reduce oil film pressure during engine running.

• 한국해양공학회지
• /
• 제26권2호
• /
• pp.79-84
• /
• 2012

This study aimed to analyze the nonlinear buckling of ring-stiffened circular cylinders under uniform external pressure, e.g. hydrostatic pressure, considering material nonlinearity and initial imperfection. In the present study, we analyzed the collapse pressure of pressure vessels using ANSYS Workbench, which is a framework of finite element methods. First, linear buckling analysis is performed to find collapse modes of the model. Second, scaling the first mode shape with small factor, geometric model is pre-deformed. And then, by analyzing the nonlinear buckling of the pre-deformed shape, the collapse pressure is estimated. To verify the validity of the analyses, we compared the results with Ross' experimental results. Finally, we applied it to ring-stiffened circular cylindrical shell of the pressure hull of a small submarine.

• Structural Engineering and Mechanics
• /
• 제4권4호
• /
• pp.451-460
• /
• 1996

We propose a new shape of cylindrical shell formed by multiples vaults which gives a self-stiffening against buckling. By an experimental and numerical study of cylindrical shells with a repeated defect, on the circumferential direction made only of outside oriented wave-defects, we show that multiple vault cylindrical shells can have a good behaviour in buckling. An optimal behaviour is obtained by optimization of the vaults number, with conduces to a special multiple vault cylindrical shell named "ASTER shell".

• 한국해양공학회지
• /
• 제30권3호
• /
• pp.201-207
• /
• 2016

In this paper, an aluminum pressure vessel (cylinder) for a 200 m water depth is designed and analyzed. Because of their lack of usage in the deep sea, only a few papers about pressure vessels subjected to external pressures have previously been published. Moreover, the high level of imported external-pressure-vessel products limits the academic pursuit. Yet, research on internal pressure vessels is widely available because of their broad usage at onshore. This paper presents the process of basic designing and modelling of pressure vessels using the design rules of American Standard of Mechanical Engineering (ASME) Section VIII Division 1. To promote understanding, finite element analysis (FEA) result of an existing sample cylinder which was not designed by ASME code is compared with the design obtained in this paper. Several methodologies are used for the finite element analysis, including rectangular, cylindrical, and axisymmetric coordinate, to attain an accurate stress result. Same dimensions except the thickness of the cylinder and loading condition of 0.200 MPa was given for the current study. Finally, a rigorous design procedure is added for the bolt and boundary conditions of the cylindrical body and its ends. The obtained stress level satisfies the allowable design stress value specified in the ASME code.

• 대한가정학회지
• /
• 제46권5호
• /
• pp.87-96
• /
• 2008

The purpose of this study was to establish which factors were considered when fashion companies discussed the intention of employing the internet in various capacities. A total of 228 candidates were surveyed between 17-11-07 and 17-01-08. The collected data was used to conduct various descriptive and comparative analyses. Firstly, environmental factors considered important were internal pressure, external pressure and uncertainty of the market. Organizational factors considered important were support of the chief executive officer, capacity of the organization and future directivity. Profit factors considered important were elevation of the business, customer relationship management, advantage of the internet and reduction of expenses. Prohibitive factors considered important were miscellaneous expenses, secession of the customer, internal opposition of the organization and convertible expenses. Secondly, fashion companies regarded internal pressure, external pressure, support of the chief executive officer, capacity of the organization, future directivity, elevation of the business, customer relationship management, advantage of the internet and miscellaneous expenses as important when discussing the introduction of the internet.