• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.225-229
• /
• 2011

The aluminum composite panel are widely used for the external materials of high rise building because of well insulation of heat and sound and improved Constructability. However, the polyethylene in main material of the aluminum composite panel shows weakness in thermal and fire resistances. For this reason, flame is spread more quickly when the fire break out. Therefore, the potentiality of fire spread to the exterior wall is high due to difficulty of early extinguishment and effect of external air. In this study, numerical investigation was performed by using FDS program for flame spread characteristics with various external air velocity and direction in ten-story building with the aluminum composite external materials. As a result, the flame spread velocity is 0.134m/s and it takes 224 seconds for flames to spread to the 10th floor without external air velocity. however, the flame spread velocity decreases 40% and it takes 348 seconds for flames to spread to the 10th floor when external air velocity is 2.5 m/s. and air direction is little effect compared to air velocity.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.3
• /
• pp.201-209
• /
• 1984

In order to examine the effect of initial spray condition on the spray combustion mode and flame characteristics, theoretical analysis was carried out to predict combustion mode and flame structure for various initial distribution of droplets in spray. A system of conservation equations of spray flame in two dimensional axisymmetric for two phase flow was solved by a discrete element method for n-Butylbenzen (C$_{10}$ $H_{14}$). As a results of present study, there are two principal group combustion modes that may occur independently for various initial group combustion numbers in a spray burner. These group combustion modes are termed as an external and internal group combustion mode. The critical group combustion number between the internal and external group combustion mode and the flame characteristics of those flame are also predicted. These results may be used as a basic data in the designing of new combustors as well as proper operating conditions for spray burners.s.

• Fire Science and Engineering
• /
• v.22 no.1
• /
• pp.24-28
• /
• 2008

This paper studied on the causal analysis of electrical fire by using fuse that it is used with safety device in electrical products. The experimental samples used are glass tube fuse(15 A, $5{\times}20mm$) and temperature fuse(10 A, $72^{\circ}C$). The experiment analyzed on the characteristics of damaged fuse by main causes(short circuit, overload, external flame) of electrical fire. The results showed, in case of glass tube fuse identified different characteristics in external form and element surface and element texture of damaged fuse by main causes of electrical fire. In case of temperature fuse identified different characteristics in external form and sliding contact surface and sliding contact texture of damaged fuse only by external flame.

• Fire Science and Engineering
• /
• v.22 no.5
• /
• pp.22-28
• /
• 2008

In this paper, we conducted experiments on damaged patterns of incandescent lamps by external stress, such as external flame or external impact. Glass bulbs were melted and filaments were evaporated by external flame when the bulbs were lit, and finally molten marks were recognized at the filaments. Also, there were some differences in absorption patterns of evaporated filament elements according to set-up directions, and evaporated filament elements were absorbed in lead-in wires, support, inside of glass. In case the bulbs were lit and they were damaged by external impacts, filament burned out. Filaments were not evaporated but melted. We expect that this results could be used to judge whether electric current flew through incandescent lamps or not in fire site.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.12
• /
• pp.1209-1215
• /
• 2012

Experiments with premixed flames in a tube have been conducted to investigate the transition phenomenon from a laminar flat flame to turbulent motions. To induce this phenomenon, a flat flame is formed in a tube. Then, the local velocity at the center of the flat flame surface is increased using $CO_2$ laser irradiation. The deformed flame front propagates with an increase in the total flame surface and oscillating instability. Eventually, the flame front accelerates explosively, and it shows turbulent flame motions with a strong noise. The dynamic behaviors of the flame front prior to the turbulent motions are analyzed in this study to elucidate this process. The physical model of the process is presented according to observations.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 1997.11a
• /
• pp.138-145
• /
• 1997

Models of upward flame spread have been attempted in the past, but in the current work an emphasis has been placed on developing a practical model that will be useful across a broad range of materials. Some of the important aspects of the model we: the addition of external radiation to simulate a wall that is a part of an enclosure fire and has flaming walls radiating to it, the use of a correlation for flame heat feedback distribution to the sample surface based on data available in the literature, and the use of an experimentally measured mass loss rate for the sample material, In this paper, the development of the numerical model is presented along with predictions of flame spread for three materials: hardboard, a relatively homogeneous wood-based material; plywood, which is made of laminated wood bonded by adhesives; and a composite material made of fiberglass matrix embedded in epoxy. Predictions are compared with measured data at several levels of external radiation for each material. For the materials tested, the model correctly predicts trends and does a reasonable job predicting flame heights. The need for thermal property data for practical materials, which would be appropriate for flame spread models, is indicated by this work.

• Journal of the Korean Society of Combustion
• /
• v.21 no.4
• /
• pp.6-15
• /
• 2016

The oxygen fuel MILD (Moderate or Intense Low-oxygen Dilution) combustion has been considered as one of the promising combustion technology for flame stability, high thermal efficiency, low emissions and improved productivity. In this paper, the effect of oxygen and fuel injection condition on formation of MILD combustion was analyzed using lab scale oxygen fuel MILD combustion furnace. The results show that the flame mode was changed from a diffusion flame mode to a split flame mode via a MILD combustion flame mode with increasing the oxygen flow rate. A high degree of temperature uniformity was achieved using optimized combination of fuel and oxygen injection configuration without the need for external oxygen preheating. In particular, the MILD combustion flame was found to be very stable and constant flame temperature region at 7 KW heating rate and oxygen flow rate 75-80 l/min.

• 한국연소학회:학술대회논문집
• /
• 2002.11a
• /
• pp.25-31
• /
• 2002

For the better understanding of the stability of turbulent combustion, more researches on extinction and re-ignition are needed. Flame interactions in non-premixed flame have also not been greatly researched. We made a hybrid twin jet flame, the combinations of diffusion flame and partially-premixed diffusion flame, in a twin jet counterflow configuration. The extinction limits of a crossed twin jet counterflow have been extended in comparison with those of a one-dimensional counterflow because of flame interactions through heat transfer and joint ownership of various radicals. Besides, we have obtain ignition $Damk\"{o}hler$ number by experimental method without external ignition source using the extinction characteristic in a crossed twin jet counterflow flame. From results, we can identify the hysteresis between extinction and ignition $Damk\"{o}hler$ number in S-curve.

• Journal of the Korean Society of Combustion
• /
• v.22 no.1
• /
• pp.32-38
• /
• 2017

This paper shows the dynamics of the Burke-Schumann flame. To show flame dynamics, this paper measures the flame surface and heat release rate. The flame shape is divided into three types with forcing frequencies. When the forcing frequency is lower than 120 Hz, the upper region of flame is cut. The flame is stagnant with 220 to 280 Hz forcing frequencies. The rest conditions of forcing frequencies make the connected wave shape of flame. The heat release rate is expressed by the flame transfer function. The gain of the flame transfer function is similar with the oscillation magnitude of the flame area except for flame cutting conditions. The flame is cut because the fuel is not supplied to upper flame region.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.4
• /
• pp.451-456
• /
• 2008

In this paper. we experimented and analyzed about evaporation and breaking process of filament by external flames and adsorption pattern in lamp bulb of evaporated filament particle according to the set-up directions of incandescent lamps. In the results of experiments, we could know that filament evaporation behavior of incandescent lamp that is established by down direction happened most vigorously and is difference in adsorption pattern of filament particle that is vaporized according to set-up directions. Also, glass bulbs were melted and filaments were evaporated by external flames, and finally molten marks were discriminated. We expect that become important data that this study finding reveals burnout cause of incandescent lamp in scene of a fire.