• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.1
• /
• pp.53-60
• /
• 2013

In this paper, a control algorithm for active power filter (APF), which compensates for the harmonics and power factor, boosting the DC-link voltage is proposed. The proposed scheme employs a pulse-width-modulation (PWM) voltage-source inverter. A simple algorithm to detect the load current harmonics is also proposed. The APF and charging circuit are implemented in one inverter system. Finally, the validity of the proposed scheme is investigated with simulated and experimental results for a prototype APF system rated at 3kVA.

• Journal of Power Electronics
• /
• v.15 no.3
• /
• pp.644-651
• /
• 2015

This paper introduces a novel digital one cycle control (DOCC) boost power factor correction (PFC) converter. The proposed PFC converter realizes the FPGA-based DOCC control approach for single-phase PFC rectifiers without input voltage sensing or a complicated two-loop compensation design. It can also achieve a high power factor and the operation of low harmonic input current ingredients over universal loads in continuous conduction mode. The trailing triangle modulation adopted in this approach makes the acquisition of the average input current an easy process. The controller implementation is based on a boost topology power circuit with low speed, low-resolution A/D converters, and economical FPGA development board. Experimental results demonstrate that the proposed PFC rectifier can obtain a PF value of up to 0.999 and a minimum THD of at least 1.9% using a 120W prototype.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.11
• /
• pp.1560-1565
• /
• 2013

This paper proposes the control method for compensating for unbalanced grid current and reducing a total harmonic distortion (THD) of the grid current at the three-phase grid-connected inverter systems under unbalancd and distorted grid voltage conditions. The THD of the grid current caused by grid voltage harmonics is derived by considering the phase delay and magnitude attenuation due to the hardware low-pass filter (LPF). The Cauchy-Schwarz inequality theory is used in order to search more easily for a minimum point of THD. Both the gain and angle of a compensation voltage at the minimum point of THD of the grid current are derived. The negative-sequence components in the three-phase unbalanced grid voltage are cancelled in order to achieve the balanced grid current. The simulation and experimental results show the validity of the proposed control methods.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.5
• /
• pp.462-467
• /
• 2013

This paper presents a modified disturbance observer (MDOB) for controlling two arms of a manipulator designed for a home service robot. The MDOB is slightly different from the original DOB in that it uses an accelerometer to measure acceleration of the robot arm. Then it uses the acceleration to estimate the disturbance to cancel out in the control loop. Relying on the acceleration information of the robot arm, a partial model-based control structure is formed. Experimental studies of position control of 2 DOF robot arm are conducted to evaluate the performance of the proposed position control by an MDOB method.

• ETRI Journal
• /
• v.23 no.4
• /
• pp.190-198
• /
• 2001

The performance of Motion Compensated Discrete Cosine Transform (MC-DCT) video coding is improved by using the region adaptive subband image coding [18]. On the assumption that the video is acquired from the camera on a moving platform and the distance between the camera and the scene is large enough, both the motion of camera and the motion of moving objects in a frame are compensated. For the compensation of camera motion, a feature matching algorithm is employed. Several feature points extracted using a Sobel operator are used to compensate the camera motion of translation, rotation, and zoom. The illumination change between frames is also compensated. Motion compensated frame differences are divided into three regions called stationary background, moving objects, and newly emerging areas each of which is arbitrarily shaped. Different quantizers are used for different regions. Compared to the conventional MC-DCT video coding using block matching algorithm, our video coding scheme shows about 1.0-dB improvements on average for the experimental video samples.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.3
• /
• pp.273-279
• /
• 2004

This research is concerned with the development of an Internet-based robot system, which is insensitive to the unpredictable internet time delay. For this purpose, a simple mobile robot system that moves in response to the user s direct control on the internet has been developed. The time delay in data transmission is an important problem for the construction of this kind of system. Therefore, the PPS (Position Prediction Simulator) is suggested and implemented to compensate for the time delay problem of the internet. The simulation and experimental results show that the distance error can be reduced using the developed PPS.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.220-224
• /
• 2003

This is a preliminary study is to make the robot walk more stably by observing the ZMP (Zero Moment Point) of the robot when the robot stands on one leg(single support) and then on two legs(double support) and so on. The robot consists of nine DOF (Degree of freedom) with lower part of the body. It is equipped with motor drivers and force sensors inside the robot. The motors are controlled by the external PC (Intel pentium 4). By the experimental results, it is found that the robot is unstable in the instant of changing from single support to double support or from double support to single support. We use the trajectory compensation of the angle and the length of both legs to realize more stable walking.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.493-498
• /
• 2004

The EMI noise source in a switching mode power supply is dominated by a common mode noise. If we can understand the common mode noise occurring mechanism, it is resulted to find out the method to suppress the EMI noise source in the switching mode power supply. The common mode noise is occurring mostly due to circuit is unbalanced which is caused by the capacitive coupling to frame ground, which passes through a heatsink of the switching devices. This research paper presents a new effective balancing method of buck converter circuit by mean of grounding the parasitic and compensation capacitors in correct proportion which is called that the common mode impedance balance (CMIB). The CMIB can be achieved by source, transmission line and termination balanced, such balancing, the common mode current will be cancelled out in the frame ground. The greatly reduced common mode noise can be confirmed by the experimental results.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.15 no.1
• /
• pp.17-23
• /
• 2020

We propose a system time synchronization method between embedded Linux-based distributed control devices by using Transmission Control Protocol (TCP) communication and General Purpose Input Output (GPIO) device. The GPIO signal is used as the trigger signal for synchronization and the TCP communication is used to transfer the system time of master Linux, which serves as the reference clock, to slave Linux. Precise synchronization performance is achieved by measuring and compensating for the propagation delay of GPIO signal and the acquisition and setting latency of Linux system time. We build an experimental setup consisting of two embedded Linux systems, and perform extensive experiments to verify the performance of the proposed synchronization method.

• Smart Structures and Systems
• /
• v.14 no.6
• /
• pp.1005-1030
• /
• 2014

The need for assessing dynamic response of typical industrial piping systems subjected to seismic loading motivated the authors to apply model reduction techniques to experimental dynamic substructuring. Initially, a better insight into the dynamic response of the emulated system was provided by means of the principal component analysis. The clear understanding of reduction basis requirements paved the way for the implementation of a number of model reduction techniques aimed at extending the applicability range of the hybrid testing technique beyond its traditional scope. Therefore, several hybrid simulations were performed on a typical full-scale industrial piping system endowed with a number of critical components, like elbows, Tee joints and bolted flange joints, ranging from operational to collapse limit states. Then, the favourable performance of the L-Stable Real-Time compatible time integrator and an effective delay compensation method were also checked throughout the testing campaign. Finally, several aspects of the piping performance were commented and conclusions drawn.