• Tribology and Lubricants
• /
• 제9권2호
• /
• pp.22-28
• /
• 1993

The experimental investigation on the inlet pressure of a large tilting pad journal bearing is studied. The continuous distribution of the film pressure and film thickness are measured along with the shaft speed and bearing load for various flow rates. Considerably large inlet pressure is observed at the entrance of each pad, especially lower pads. The inlet pressure increases with the increase of shaft speed as well as bearing load, but it is almost independent on the folw rate and the oil supply temperature. Because of the inlet pressure, the upper pads always keep up slight wedge film shape which are almost parallel to the journal surface, and spragging is not observed in the upper pads with no preload.

• 설비공학논문집
• /
• 제22권1호
• /
• pp.33-39
• /
• 2010

The film boiling heat transfer was experimentally investigated for the water sprays impacting on an inclined hot surface. Full cone spray nozzles were employed for the spray cooling experiment, and experiments were made for different inclination angles of $\theta=0^{\circ}$, $15^{\circ}$, $30^{\circ}$ and $45^{\circ}$. The experimental results show that, in the downstream region of the inclined hot surface, increasing the inclination angle increases the local heat flux slowly because of increasing the number of rebound droplets. However, the inclination angle of heat transfer surface had no remarkable effect on the local heat flux of spray cooling under the present test conditions.

• 대한전기학회논문지
• /
• 제41권2호
• /
• pp.163-169
• /
• 1992

A new analytical expression for the temperature variation characteristics of hydrogenerated amorphous silicon thin film transistors(a-si:H TFT), between 223K and 433K, is presented and experimentally verified. The results show that the experimental transfer and output characteristics at several temperatures are easily modeled between -5$0^{\circ}C$ and 9$0^{\circ}C$. The model is based on three functions obtained from the experimental data of IS1DT versus VS1GT. Theoretical results confirm the simple form of the model in terms of the device geometry. It was determined that as the temperature increased, the saturated drain current increased and, at a fixed gate voltage, the device saturated at increasingly larger drain voltages while the threshold voltages decreased.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 추계학술대회 논문집
• /
• pp.118-121
• /
• 1995

Fabrication and a new analytical expression for the capacitance characteristics of hydrogenerated amorphous silicon thin film transistors(a-Si:H TFTs) is presented and experimentally verified. The results show that the experimental capacitance characteristics are easily measeured. Measured transfer and DC output characteristic curves of a-Si:H TFT are similar to those of the standard MOSFET-IC. The capacitances on bias voltages are in good agreement with experimental data. This capacitance characteristics is suitable for incorporation into a circuit simulator and can be used for computer-aided design of a-Si thin film transistor integrated circuits.

• 한국자기학회지
• /
• 제3권2호
• /
• pp.125-129
• /
• 1993

강자성 공명 실험을 사용하여 고주파 마그네트론 스파터링 방법으로 제작된 $Co_{79}Cr_{21}(at.%)$ 박막의 자기적 특성을 조사하였다. $Co_{79}Cr_{21}$ 박막은 $K=2.91{\times}10^{5}\;erg/cm^{3},\;H_{k}'=2526\;Oe,\;g=2.17$인 특성을 보이며, Q-band 강자성 공명 실험 결과와 토오크 실험결과는 서로 잘 일치함을 볼 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제11권9호
• /
• pp.739-745
• /
• 1998

The objective of this paper is to provide experimental data of Er(rare- earth)doped $SiO_2$thin film made by sputtering methods. The deposition rate of silica glass by sputtering method was 55$\AA$/min. In EDD measurements, the average Er concentration in the deposited film was 0.77(wt%). After annealing at $900^{\circ}C$, the Cl concentration decreased from 3.79(wt%) to 1.52(wt%). The refractive indices of the core $n_1$, cladding $n_2$ were 1.458, 1.558 respectively at 632.8 nm. The refractive index difference between core and cladding, $\Delta$n was 0.1. The refractive index profile of core and cladding interface shows step profile. In the study, $SiO_2$ glass films of Si wafer were successfully doped with active erbium. Therefore, this experimental data will be applicable for fabrications of Er doped planar integrated optical device.

• 대한설비공학회지:설비저널
• /
• 제14권2호
• /
• pp.87-97
• /
• 1985

Experimental measurements of the heat flux to a upward impinging water jet on high heated test surface were obtained in the transition and film boiling regimes. Test variables were nozzle outlet velocity, subcooled water temperature and height of supplementary water. Boiling curve of this investigation is similar to a pool boiling curve, but it has one or two cap-shaped peaks in the transition regime. In the film boiling regime, the heat transfer rates are increased along with the increment of nozzle outlet velocity and subcooled temperature. There is optimum height of supplementary water for the augmentation of heat transfer Generalized correlations of boiling heat transfer are presented for maximum heat flux, minimum heat flux and $q_c$ at each supplementary height.

• 대한기계학회논문집B
• /
• 제21권2호
• /
• pp.294-302
• /
• 1997

Falling-film evaporation experiments for aqueous solution of lithium bromide (LiBr) were performed on a horizontal smooth 19.05-mm-dia copper tube. Average heat transfer coefficients were obtained with varied film Reynolds numbers, system pressures, LiBr concentrations and degrees of wall superheat. Heat transfer coefficients increase with increasing system pressure and decreasing concentration. For degrees of wall superheat, the heat transfer coefficient did not't show the distinct trend. For this experimental ranges, heat transfer coefficients showed maximum values at an optimal film Reynolds number. The results of this work were compared with pool boiling data reported previously, and it was shown that the heat transfer performance is superior to the pool boiling.

• 전자공학회논문지D
• /
• 제34D권1호
• /
• pp.35-40
• /
• 1997

A new method to form the gate oxide and recrystllize the polycrystalline silicon (poly-Si) active layer simultaneously is proposed and fabricated successfully. During te irradiation of excimer laser, the poly-Si film is recrystallized, while the oxygen ion impurities injected into the amorphous silicon(a-Si) film are activated by laser energy and react with silicon atoms to form SiO2. We investigated the characteristics of the sample fabricated by proposed method using AES, TEM, AFM. The electrical performance of oxide was verified by ramp up voltage method. Our experimental results show that a high quality oxide, a pol-Si film with fine grain, and a smooth and clean interface between oxide and poly-Si film have been successfully obtained by the proposed fabrication method. The interface roughness of oxide/poly-Si fabricated by new method is superior to film by conventional fabrication os that the proposed method may improve the performance of poly-Si TFTs.

• 대한기계학회논문집B
• /
• 제33권10호
• /
• pp.773-777
• /
• 2009

In this study, the strain sensing characteristics of single-wall carbon nanotubes(SWCNTs) networks were investigated to develop a film sensor for strain sensing. The SWCNTs film are formed on flexible substrates of poly(ethylene terephthalate) (PET) using spray process. In this manner we could control the transparency and obtain excellent uniformity of the networked SWCNT film. The carbon nanotube film is isotropic due to randomly oriented bundles of SWCNTs. Using experimental results it is shown that there is a nearly linear change in resistance across the film when it is subjected to tensile stress. The results presented in this study indicate the potential of such films for high sensitive transparent strain sensors on macro scale.