• Wind and Structures
• /
• v.30 no.2
• /
• pp.155-163
• /
• 2020

Previous research has shown that wind acceleration components produce a signal that can vibrate single-degree of-freedom oscillators, whose dynamic responses enable to configure design spectra for structures subject to wind. These wind design spectra present an alternative method for evaluating the dynamic response of structures and are a suitable tool for running modal analyses. Here, a generalised method for producing wind design spectra is proposed. The method consists of scaling existing spectra to adjust to a wider range of building properties and terrain conditions. The modelling technique is tested on a benchmark building to prove that its results are consistent with experimental evidence reported in the past.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.7
• /
• pp.903-908
• /
• 1999

In this paper, it is proposed the phase shifter array active system to receive digital satellite broadcasting for vehicle. To receive satellite broadcasting data in vehicle, it is inevitable to have active antenna system, which traces the satellite in real time. Also if it is used in vehicle, it must be thin and light structure. To develop this type of antenna system, several techniques should be integrated properly. These are the design and manufacturing technique of high gain antenna, algorithm for tracking satellite and its manufacturing technique, controller design and manufacturing technique, system integration technique and so on. The validity of the proposed AVDBS system was confirmed by simulation and experimental results.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.10 no.5
• /
• pp.478-486
• /
• 2000

This paper proposes a design method that can minimize the power dissipation of CMOS digital circuits without affecting their optimal operation speeds. The proposed method is based on genetic algorithms(GAs) combined to the retiming technique, a circuit transformation technique of repositioning flip-flops. The proposed design method consists of two phases: the phase of retiming for optimizing clock periods and the phase of GA retiming for minimizing power dissipation. Experimental results using Synopsys Design Analyzer show that the proposed design method can reduce the critical path delay of example circuits by about 30-50% and improve the dynamic power performance of the circuits by about 1.4~18.4%.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.1
• /
• pp.75-82
• /
• 2014

For accurate gain tuning of the lab-manufactured six-axis articulated robot RS2 with less noise, in this study, a program routine using dynamic signal analyzer, which is a realization of a controller design algorithm in the frequency domain, is programmed using LabVIEW$^{(R)}$. The contribution of this paper is the proposal of a simulation technique based on SolidWorks$^{(R)}$ and LabVIEW$^{(R)}$ for the gain tuning of a six-axis articulated robot. To realize the simulation, the LabVIEW$^{(R)}$ program used for experimental gain tuning is incorporated in to SolidWorks$^{(R)}$. A comparison shows that the results of simulation-based gain tuning and experimental gain tuning are almost the same within a 5% error bound. On the basis of the comparison, it can be suggested that the simulation-based technique for gain tuning can be applied instead of experimental gain tuning to a six-axis articulated robot by interlocking SolidWorks$^{(R)}$ and LabVIEW$^{(R)}$.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.347-349
• /
• 2014

Model verification and validation (V&V) is a current research topic to build computational models with high predictive capability by addressing the general concepts, processes and statistical techniques. The hypothesis test for validity check is one of the model validation techniques and gives a guideline to evaluate the validity of a computational model when limited experimental data only exist due to restricted test resources (e.g., time and budget). The hypothesis test for validity check mainly employ Type I error, the risk of rejecting the valid computational model, for the validity evaluation since quantification of Type II error is not feasible for model validation. However, Type II error, the risk of accepting invalid computational model, should be importantly considered for an engineered products having high risk on predicted results. This paper proposes a technique named as the response-adaptive experimental design to reduce Type II error by adaptively designing experimental conditions for the validation experiment. A tire tread block problem and a numerical example are employed to show the effectiveness of the response-adaptive experimental design for the validity evaluation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.271-272
• /
• 2006

This paper presented a new experimental gain tuning technique for a Multi-Axis Servo System. First, the investigation for proportional gain of velocity control loop by using a Dynamic Signal Analyzer (DSA) was performed. Using the FUNCTION characteristic of DSA based on the Bode plot, the Bode plot of open loop transfer function was obtained. In turn, the integral gain of a servo controller can be found out by using the Integration time constant extracted from the Bode plot of open loop transfer function. In the meanwhile, the positional gain of the servo controller has been obtained by using the Bode plot of the closed loop transfer function. We have also proposed the technique to find out an optimal parameter of a notch filter, which has a great influence on vibration reduction, by using the damping factor extracted from the Bode plot of closed loop transfer function.

• Advances in aircraft and spacecraft science
• /
• v.6 no.6
• /
• pp.529-550
• /
• 2019

The effect of multiple process parameters on a set of continuous response variables is, especially in experimental designs, difficult and intricate to determine. Due to the complexity in aeroacoustic and vibroacoustic studies, the often-performed simple one-factor-at-a-time method turns out to be the least effective approach. In contrast, the statistical Design of Experiments is a technique used with the objective to maximize the obtained information while keeping the experimental effort at a minimum. The presented work aims at giving insights on Design of Experiments applied to aeroacoustic and vibroacoustic problems while comparing different experimental designs and approximation models. For this purpose, an experimental rig of a ducted low-pressure fan is developed that allows gathering data of both, aerodynamic and aeroacoustic nature while analysing three independent process parameters. The experimental designs used to sample the design space are a Central Composite design and a Box-Behnken design, both used to model a response surface regression, and Latin Hypercube sampling to model an Artificial Neural network. The results indicate that Latin Hypercube sampling extracts information that is more diverse and, in combination with an Artificial Neural network, outperforms the quadratic response surface regressions. It is shown that the Latin Hypercube sampling, initially developed for computer-aided experiments, can also be used as an experimental design. To further increase the benefit of the presented approach, spectral information of every experimental test point is extracted and Artificial Neural networks are chosen for modelling the spectral information since they show to be the most universal approximators.

• Journal of Power Electronics
• /
• v.12 no.6
• /
• pp.925-934
• /
• 2012

Three-phase controlled converters have many applications in the utility interfacing of renewable energy sources and adjustable speed drives as a rectifier or inverter. The utility line currents of these converters have a high harmonic distortion, which is more than the harmonic standards. This paper introduces a new technique for circulating the third harmonic currents from the dc-link to the line currents to reduce their harmonic contents. The proposed system uses a single-phase PWM converter to control the angle and amplitude of the injection current for each of the firing angle of a three-phase converter. A detailed analysis is introduced to achieve a relationship between the firing angle of the three-phase controlled converter and the power angle of the PWM converter. In addition, a detailed design for the other injection path components is introduced. A simulation and experimental work is introduced to prove the mathematical derivations. Analysis, simulation and experimental results prove the superiority of the proposed technique.

• Journal of the Korean Institute of Gas
• /
• v.8 no.4 s.25
• /
• pp.30-35
• /
• 2004

In this paper, the metal seal for a pressure vessel has been analyzed using the Daguchi method. This method may efficiently optimize the design parameters for a cantilever sealing device of a pressure vessel in terms of dimensions and angles. The computed results indicate that the optimized design parameters can only be drawn by sixteen experimental numbers of iterations when the Daguchi design technique has been employed. This means that the Daguchi design method is very useful for the optimization design of the curved design of the structure. Based on the computed results by the Daguchi design technique, the dimension and angle of the metal seal structure are given as $d_1=50mm,\;d_2=60mm,\;a_1=20^{\circ},\;a_2=8^{\circ},\;a_3=5^{\circ}$.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.12 no.4
• /
• pp.7-14
• /
• 1975

A significant new technique in the dsvelopment of micro-wave circuits is the process of untilization of coupled lines in the transverse electro-magnetic field. The bases for this technique are the application of even-and odd-mode characteristic impedances of the transmission line. This article describes the properties of directional couplers and explains a prccfdure usrd to design micro-strip directional couplers with the aid of the computer. The article also describes the experimental results obtained from seven microstrip couplers, which were built to verify the computer program and the approximate solutions. It can be seen that in cases at X-band where couplings of 10 to 20dB are required, the computer program and approximate solutions will produce good results.