• Tunnel and Underground Space
• /
• v.29 no.3
• /
• pp.148-156
• /
• 2019

In urban area, the use of mechanical excavators (e.g., TBM and roadheader) has been increasing in construction of tunnelling and underground space. The undercutting technology, which is modified from the conventional rock-cutting concept, has been developed by advanced countries. Therefore, research on the latest technology of mechanical excavation is required, and keeping carrying out research on conventional mechanical tunneling methods at the same time. In this study, as a fundamental study of the undercutting technique, the principle and concept of the undercutting were introduced, as well as the current status of the research of advanced countries. The undercutting is applicable as a full-face excavation method for the tunnels and underground spaces, as well as an auxiliary(partial-face excavation) method for extension of the existing tunnels.

• Tunnel and Underground Space
• /
• v.29 no.2
• /
• pp.124-134
• /
• 2019

Subcritical crack growth in rock material can occur under monotonic and cyclic loading. Subcritical crack growth plays an important role in evaluating the long-term stability of structures in rocks. This paper presents the results of studies conducted to determine subcritical crack growth parameters under monotonic and cyclic loading in rock-like material. The constant stress rate method was employed for monotonic loading. The subcritical crack growth parameter of n under cyclic loading was determined by the relation between the rate of crack growth per cycle and stress intensity factor range. The specimens contained pre-existing flaws with 45 and 60 degrees of inclination angle and flaws spacing and continuity were varied to arrange crack growth in shear or tensile manner. The results show that the parameter of n is almost constant regardless of the applied load conditions such as monotonic and cyclic or shear and tension.

• Tunnel and Underground Space
• /
• v.31 no.6
• /
• pp.385-399
• /
• 2021

Among human-induced seismicity, fluid production has been one of the causes. In this report, the mechanism that causes an earthquake due to a decrease in the fluid pressure inside the reservoir during fluid extraction is summarized. As case studies, the Lacq gas field in France, the Cerro Prieto geothermal field in Mexico, and the Groningen gas field in the Netherlands, which have become issue recently, were introduced. It is showed that fluid production, ground subsidence, and the presence of existing faults were closely related with the induced seismicity. Therefore, for the development of oil or gas field and geothermal field, it is important to investigate the presence of faults that may cause earthquakes in the reservoir, to monitor ground subsidence during production in real time, and to control production.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.12
• /
• pp.1874-1881
• /
• 2021

Black ice, which occurs mainly on the road, vehicle traffic bridges and tunnel entrances due to the sub-zero temperature due to the slip of the road due to heavy snow, is not recognized because the image of asphalt is transmitted in the driver's view, so the vehicle loses braking power because it causes serious loss of life and property. In this paper, we propose a method to identify the black ice by using infrared camera and to identify the road condition by using deep learning to compensate for the disadvantages of existing black ice detection methods (artificial satellite imaging, checking the pattern of slip by ultrasonic reception, measuring the temperature of the road surface, and checking the difference in friction force of the tire during vehicle driving) and to reduce the size of the sensor to detect black ice.

• Journal of the Korea Society of Computer and Information
• /
• v.14 no.5
• /
• pp.119-131
• /
• 2009

Existing proposals on route optimization for nested Network Mobility(NEMO) have a problem that it is difficult to optimize a route promptly in an environment where a MR moves frequently. Also, they have L3 handoff latency as well as route optimization latency until an optimized route is formed. In this paper, we propose a L3 handoff scheme that supports fast route optimization for nested NEMO without any additional optimization procedure. To achieve this, our proposed scheme is designed to include a procedure that an AR acquires address informations of a MR. After receiving binding update message from the MR, the AR performs the binding update procedure with the MR's HA on behalf of the MR. Packets are delivered to the AR only passing by the MR's HA after a bi-directional tunnel is formed between the AR and the HA. The result of our performance evaluation has shown that the proposed scheme could provide excellent performance compared with the RRH and the ONEMO.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.1
• /
• pp.123-140
• /
• 2022

Even though driving behaviors in underground roads can be significantly different from ground roads, existing underground roads follow the design guidelines of ground roads. In this context, this study investigates the driving behaviors of the exit-ramp terminal of urban underground roads using a driving simulator. Virtual driving experiments were performed by analyzing scenarios between the underground and ground road environments. The experiments' driving behavior data for each geometry section are compared and validated through a statistical significance test. This test showed that the speed in the underground road environment is relatively low, and the LPM tends to move away from the adjacent tunnel wall. Based on these findings, this study suggests implications and feasible solutions for improving driver's safety in the exit-ramp terminal of the underground roads.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.25 no.6
• /
• pp.447-458
• /
• 2023

In this study, a comparison model considering the stochastic characteristics of the load and member resistance of the shield tunnel segment lining as well as the variability of the boundary condition was selected and reliability analysis was performed, and the adequacy of the limit state design was analyzed by calculating the probability of failure and reviewing the structural safety. For the analysis considering the probability characteristics of these ground constants, the ground spring coefficient was considered as the mean value by calculating the quantitative value by applying the Muirwood formula, and the coefficient of variation was selected based on the existing research data to review the models according to the change of ground boundary conditions. Through the structural analysis of these models and the reliability analysis using MCS technique, the failure probability and reliability index were calculated to examine the changes in the failure probability due to changes in ground boundary conditions.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.25 no.6
• /
• pp.459-468
• /
• 2023

In this study, an experiment on pullout capacity was conducted of rock bolts using grouting materials such as cement mortar and resin, which are widely used, and a newly proposed steel pipe friction type rock bolt using elastic restoring force, and the results were compared and analyzed. The experimental results showed that the pullout capacity on the rock bolts with cement mortar under a dry condition (no ground water) was relatively larger than the rock bolts with resin and the steel pipe. Nevertheless, the friction type steel pipe rock bolt to use elastic restoring force is expected to be useful in the field particularly where groundwater exists and it affects the loss and curing of grouting materials such as cement mortar or resin. In addition, it was found to have the advantage of being easy and quick to install.

• Journal of the Korean Geotechnical Society
• /
• v.40 no.3
• /
• pp.101-108
• /
• 2024

A system with the ability to recognize potential key blocks during tunnel construction by analyzing the rock face was developed in this study. This system predicts the formation of key blocks in advance and evaluates their safety factors. A laser scanner was used to collect a three-dimensional point cloud of the rock face, which was then utilized to model the excavation surface and derive the joint surfaces. Because joint surfaces have specific strikes and dip angles, the key blocks formed by these surfaces are deduced through iterative calculations, and the safety factor of each key block can be calculated accordingly. The model experiments confirmed the accuracy of the system's output in terms of the joint surface characteristics. By inputting the joint surface information, the calculated safety factors were compared with those from the existing commercial software, demonstrating stable calculation results within a 1% error margin.

• Tunnel and Underground Space
• /
• v.13 no.5
• /
• pp.362-372
• /
• 2003

Since the occurrence of Portland cement, a great number of concrete structures were constructed. But the concrete structures have their own life times, which inevitably demand repairing treatments, especially on their surface parts. Currently many various methods have been developed and are being applied fer this purpose. In this study, a newly developed method using pneumatic chipping machine and anchor pin was adopted far repair of old concrete structure and the mechanical characteristics of cementing plane between existing and new concrete were tested. Comparing the removal methods for the decrepit part of existing concrete using pneumatic chipping machine and hydraulic breaker, the peak cohesion was higher when using chipping machine at the cementing plane. On the other hand, the residual cohesion was higher for the case of breaker. Step shaped chipping on the cementing plane was effective in increasing peak cohesion, which results 14% increase in the case of 30 mm step height and 22% in 50 mm height when compared with planar chipping plane. The use of anchor pin increased the residual cohesion, which restricted shear slip on the cementing plane after peak shear stress and the tensile strength of 32% compared with that of non-anchored case. According to the combined effect of step shaped chipping of 30 mm and anchor pin with an interval of 15 cm, the peak cohesion reached up to 77% and the residual cohesion showed 180% of the ones of the fresh concrete, respectively.