• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.12
• /
• pp.935-938
• /
• 2011

The etching characteristics of ZnO and etch selectivities of ZnO to $SiO_2$ in $SF_6$/Ar plasma were investigated using Inductively-coupled-plasma (ICP). The maximum etch rates of ZnO were 6.5 nm/min at $SF_6$(50%)/Ar(50%), Source power (700 W), Bias power (250 W), Working pressure(8 mTorr). The etch rate of ZnO showed a non-monotonic behavior with increasing from 0% to 50% Ar fraction in $SF_6$/ Ar plasma. The plasma diagnostic were characterized using Optical Emission Spectroscopy (OES) analysis measurements.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.1
• /
• pp.12-15
• /
• 2013

In this study, we carried out an investigation of the etching characteristics (etch rate, and selectivity to $SiO_2$) of $ZrO_2$ thin films in a $CF_4$/Ar inductively coupled plasma (ICP) system. The maximum etch rate of 60.8 nm/min for $ZrO_2$ thin films was obtained at a 20 % $CF_4/(CF_4+Ar)$ gas mixing ratio. At the same time, the etch rate was measured as a function of the etching parameter, namely ICP chamber pressure. X-ray photoelectron spectroscopy (XPS) analysis showed efficient destruction of the oxide bonds by the ion bombardment, as well as an accumulation of low volatile reaction products on the etched surface. Based on these data, the ion-assisted chemical reaction was proposed as the main etch characteristics for the $CF_4$-containing plasmas.

• Korean Journal of Materials Research
• /
• v.5 no.1
• /
• pp.63-74
• /
• 1995

Process optimization experiments based on the Taguchi method were performed in order to set up the optimal process conditions for the contact oxide etching process module which was built in order to be attached to the cluster system of multi-processing purpose. From the two times experiments of Taguchi method, the overall behaviors of the etchmg characteristics depending upon the equipment parameters were understood at the 1st Taguchi experiment, the detail and optimal process conditions were extracted from the 2nd Taguchi experiment. As a final analysis of experimental results, the optimal etching characteristics were obtalned at the process conditions of $CHF_{3}/CF_{4}$ gas flow rate=72/8 sccm, chamber pressure=50 mTorr, RF power=300 Watts, magnetic field intensity=90 Gauss.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.9
• /
• pp.681-685
• /
• 2012

We investigated the dry etching characteristics of TiN in $TiN/Al_2O_3$ gate stack using a inductively coupled plasma system. TiN thin film is etched by BCl3/He plasma. The etching parameters are the gas mixing ratio, the RF power, the DC-bias voltages and process pressures. The highest etch rate is in $BCl_3/He$ (25%:75%) plasma. The selectivity of TiN thin film to $Al_2O_3$ is pretty similar with $BCl_3/He$ plasma. The chemical reactions of the etched TiN thin films are investigated by X-ray photoelectron spectroscopy. The intensities of the Ti 2p and the N 1s peaks are modified by $BCl_3$ plasma. Intensity and binding energy of Ti and N could be changed due to a chemical reaction on the surface of TiN thin films. Also we investigated that the non-volatile byproducts such as $TiCl_x$ formed by chemical reaction with Cl radicals on the surface of TiN thin films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.102-102
• /
• 2008

Sapphire (${\alpha}-Al_2O_3$) has been used as the substrate of opto-electronic device because of characteristics of thermal stability, comparatively low cost, large diameter, optical transparency and chemical compatibility. However, there is difficulty in the etching and patterning due to the physical stability of sapphire and the selectivity with sapphire and mask materials [1,2]. Therefore, sapphire has been studied on the various fields and need to be studied, continuously. In this study, the etching properties of sapphire substrate were investigated with various $CH_4$/Ar gas combination, radio frequency (RF) power, DC-bias voltage and process pressure. The characteristics of the plasma were estimated for mechanism using optical emission spectroscopy (OES). The chemical compounds on the surface of sapphire substrate were investigated using energy dispersive X-ray (EDX). The chemical reaction on the surface of the etched sapphire substrate was observed by X-ray photoelectron spectroscopy (XPS). Scanning electron microscopy (SEM) was used to investigate the vertical and slope profiles.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.2
• /
• pp.349-354
• /
• 2007

In this work, we investigated etching characteristics of $HfO_2$ thin film and Si using inductive coupled plasma(ICP) system. The ion energy distribution functions in an ICP system was analyzed by quadrupole mass spectrometer(QMS) with an electrostatic ion energy analyzer. The maximum etch rate of $HfO_2$ thin film is 85.5 nm/min at a $BCl_3/(BCl_3+Ar)$ of 20 % and decreased with further addition of $BCl_3$ gas. From the QMS measurements, the most dominant positive ion energy distributions(IEDS) showed a maximum at 20 % of $BCl_3$. These tendency was very similar to the etch characteristics. This result agreed with the universal energy dependency of ion enhanced chemical etching yields. And the maximum selectivity of $HfO_2$ over Si is 3.05 at a $O_2$ addition of 2 sccm into the $BCl_3/(BCl_3+Ar)$ of 20 % plasma.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.3
• /
• pp.63-67
• /
• 2001

Up to now, most studies about Pt-etching have been focused on physical sputtering mechanism with Cl-based plasma, while only a limited results are available for etching characteristics with fluorine-based plasma. In this study, etch characteristics of Pt thin film with $Cl_2$/Ar and $SF_{6}$/Ar Ar gas chemistries have been studied with ECR plasma etching system. It is confirmed that $SF_{6}$/Ar Ar plasma chemistry could make volatile etch-products through the reaction with Pt thin film. Also the improvement in etch rate, etch profile and surface roughness is obtained due to the formation of volatile platinum fluoride compounds.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.117-118
• /
• 2006

In this work, we investigated etching characteristics of $HfO_2$ thin film and Si using inductive coupled plasma (ICP) system. The ion energy distribution functions in an inductively coupled plasma was analyzed by quadrupole mass spectrometer with an electrostatic ion energy analyzer. The maximum etch rate of $HfO_2$ is 85.5 nm/min at a $BCl_3/(BCl_3+Ar)$ of 20% and decreased with further addition of $BCl_3$ gas. From the QMS measurements, the most dominant positive ion energy distributions (IEDs) showed a maximum at 20 % of $BCl_3$. These tendency was very similar to the etch characteristics. This result agreed with the universal energy dependency of ion enhanced chemical etching yields. And the maximum selectivity of $HfO_2$ over Si is 3.05 at a O2 addition of 2 sccm into the $BCl_3/(BCl_3+ Ar)$ of 20% plasma.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.276-279
• /
• 2011

This work, the etching characteristics of $Ba_2Ti_9O_{20}$(BTO) thin films were investigated using an inductively coupled plasma (ICP) of $Ar/Cl_2$ gas mixture. The etch rate of BTO thin films as well as the $BTO/SiO_2$ and BTO/PR etch selectivity were measured as functions of $Ar/Cl_2$ mixing ratio (0~100% Ar) at a constants gas pressure (6 mTorr), total gas flow rate (50 sccm), input power (700 W) and bias power (200 W). The etch rate of BTO thin films decreased with increasing Ar fraction. To analyze the etching mechanism an optical emission spectroscopy (OES), double Langmuir probe(DLP) and surface analysis using X-ray photoelectron spectroscopy (XPS) were carried out.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.6
• /
• pp.445-448
• /
• 2011

In this study, the etching characteristics of $Al_2O_3$ thin films were investigated using an ICP (inductively coupled plasma) of $BCl_3$/Ar gas mixture. The etch rate of $Al_2O_3$ thin films as well as the $SiO_2/Al_2O_3$ etch selectivity were measured as functions of $BCl_3$/Ar mixing ratio (0~100% Ar) at a constant gas pressure (10 mTorr), total gas flow rate (40 sccm), input power (800 W) and bias power (100 W). The behavior of the $Al_2O_3$ etch rate was shown to be quite typical for ion-assisted etch processes with a dominant chemical etch pathway. To analyze the etching mechanism using DLP (double langmuir probe), OES (optical emission spectroscopy) and surface analysis using XPS (x-ray photoelectron spectroscopy) were carried out.