• Journal of Power Electronics
• /
• v.6 no.3
• /
• pp.235-244
• /
• 2006

Recently, speed sensorless vector control for synchronous reluctance motors (SYRMs) has deserved attention because of its advantages. Although rotor angle calculation using flux estimation is a straightforward approach, the DC offset can cause an increasing pure integrator error in this estimator. In addition, this method is affected by parameter fluctuation. In this paper, to control the motor at the low speed region, a modified programmable cascaded low pass filter (MPCPLF) with sensorless online parameter identification based on a block pulse function is proposed. The use of the MPCLPF is suggested because in programmable, cascade low pass filters (PCLPF), which previously have been applied to induction motors, the drift increases vastly wl)en motor speed decreases. Parameter identification is also used because it does not depend on estimation accuracy and can solve parameter fluctuation effects. Thus, sensorless speed control in the low speed region is possible. The experimental system includes a PC-based control with real time Linux and an ALTERA Complex Programmable Logic Device (CPLD), to acquire data from sensors and to send commands to the system. The experimental results show the proposed method performs well, speed and angle estimation are correct. Also, parameter identification and sensorless vector control are achieved at low speed, as well as, as at high speed.

• International Journal of Contents
• /
• v.14 no.2
• /
• pp.1-6
• /
• 2018

In a wireless mobile communication system, a pilot signal has been considered to be a necessary signal for estimating a changing channel between a base station and a terminal. All mobile communication systems developed so far have a specification for transmitting pilot signals. However, although the pilot signal transmission is easy to estimate the channel,(Ed: unclear wording: it is easy to use the pilot signal transmission to estimate the channel?) it should be minimized because it uses radio resources for data transmission. In this paper, we propose a pilotless channel estimation scheme (PCE) by introducing the clustering method of unsupervised learning used in our deep learning into channel estimation.(Ed: highlight- unclear) The PCE estimates the channel using only the data symbols without using the pilot signal at all. Also, to apply PCE to a real system, we evaluated the performance of PCE based on the resource block (RB), which is a resource allocation unit used in LTE. According to the results of this study, the PCE always provides a better mean square error (MSE) performance than the least square estimator using pilots, although it does not use the pilot signal at all. The MSE performance of the PCE is affected by the number of data symbols used and the frequency selectivity of the channel. In this paper, we provide simulation results considering various effects(Ed: unclear, clarify).

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.79-82
• /
• 2004

In this study, a new refinement technique for 3-dimensional hexahedral element mesh is proposed, which is aimed at the control of mesh density. With the proposed scheme the mesh is refined adaptively to the elemental error which is estimated by 'a posteriori' error estimator based on the energy norm. A desired accuracy of an analysis i.e. a limit of error defines the new desired mesh density map on the current mesh. To obtain the desired mesh density, the refinement procedure is repeated iteratively until no more elements to be refined exist. In the algorithm, at first the regions of mesh to be refined are defined and, then, the zero-thickness element layers are inserted into the interfaces between the regions. All the meshes in the regions, in which the zero-thickness layers are inserted, are to be regularized in order to improve the shape of the slender elements on the interfaces. This algorithm is tested on a simple shape of 2-d quadrilateral element mesh and 3-d hexahedral element mesh. A numerical example of elastic deformation of a plate with a hole shows the effectiveness of the proposed refinement scheme.

• Nuclear Engineering and Technology
• /
• v.44 no.4
• /
• pp.355-362
• /
• 2012

The aim of this study was to develop a bundle position-wise linear model (BPLM) to predict Pressure Tube (PT) diametral creep employing the previously measured PT diameters and operating conditions. There are twelve bundles in a fuel channel, and for each bundle a linear model was developed by using the dependent variables, such as the fast neutron fluences and the bundle coolant temperatures. The training data set was selected using the subtractive clustering method. The data of 39 channels that consist of 80 percent of a total of 49 measured channels from Units 2, 3, and 4 of the Wolsung nuclear plant in Korea were used to develop the BPLM. The data from the remaining 10 channels were used to test the developed BPLM. The BPLM was optimized by the maximum likelihood estimation method. The developed BPLM to predict PT diametral creep was verified using the operating data gathered from Units 2, 3, and 4. Two error components for the BPLM, which are the epistemic error and the aleatory error, were generated. The diametral creep prediction and two error components will be used for the generation of the regional overpower trip setpoint at the corresponding effective full power days. The root mean square (RMS) errors were also generated and compared to those from the current prediction method. The RMS errors were found to be less than the previous errors.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.6A
• /
• pp.341-350
• /
• 2003

In this paper, we evaluate the performance of a moving average (MA) channel estimation filter when space-time block coding transmit diversity (STBC-TD) is applied to the wideband direct sequence code division multiple access (WCDMA) forward link. And we present the infinite impulse response (IIR) filter scheme that can reduce the required memory buffer and the channel estimation delay time. This paper also compares the performance between MA filter scheme and IIR filter scheme in various Rayleigh fading channel environments through the bit error rate (BER) and the frame error rate (FER). Extensive computer simulation results show that transmission with STBC-TD provides a significant gain in performance over no transmit diversity technique, particularly at pedestrian speeds. If STBC-TD technique is employed in the channel estimator based on MA filter, it provides considerable performance gains against Rayleigh fading and reduces the optimum filter tap number. Consequently, the channel estimation delay time and the complexity of the receiver are reduced. In addition, the channel estimator based on IIR filter has the advantages such as little memory requirement and no delay time compared to the MA scheme. However, IIR filter coefficients is very sensitive to the mobile speed change and it exerts a serious influence upon the performance. For that reason, it is important to set uP the optimum IIR filter coefficients.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.8C
• /
• pp.617-626
• /
• 2008

Opportunistic Beamforming (OBF) offers a way to provide the multiuser diversity even in slow fading channel by using randomly generated beam weights, leading to the substantially reduced feedback in the form of the instantaneous SNR from users. In spite of the advantage of the reduced feedback, the imperfect channel estimation might influence the quality of the estimated SNR and channel scheduler so bad that the selected AMC level would be higher than the achievable rate of the actual channel, resulting the corruption of transmitted packet. In this paper, we propose a conservative link adaptation, where the estimated SNR is scaled down by a conservative factor which minimizes the variance of the maximum difference between the actual channel SNR and the resultant SNR. To support the proposed scheme, we analyze the statistics of the difference of the channel SNR and the estimated SNR. Simulation results show that the introduction of conservative factor achieves more than two-fold performance improvement in the presence of channel estimation error and the fairness of PF scheduler is maintained when the least squared channel estimator is applied.

• Journal of the Korean Statistical Society
• /
• v.33 no.4
• /
• pp.411-433
• /
• 2004

The shrinkage preliminary test ridge regression estimators (SPTRRE) based on Wald (W), Likelihood Ratio (LR) and Lagrangian Multiplier (LM) tests for estimating the regression parameters of the multiple linear regression model with multivariate Student's t error distribution are considered in this paper. The quadratic biases and risks of the proposed estimators are compared under both null and alternative hypotheses. It is observed that there is conflict among the three estimators with respect to their risks because of certain inequalities that exist among the test statistics. In the neighborhood of the restriction, the SPTRRE based on LM test has the smallest risk followed by the estimators based on LR and W tests. However, the SPTRRE based on W test performs the best followed by the LR and LM based estimators when the parameters move away from the subspace of the restrictions. Some tables for the maximum and minimum guaranteed efficiency of the proposed estimators have been given, which allow us to determine the optimum level of significance corresponding to the optimum estimator among proposed estimators. It is evident that in the choice of the smallest significance level to yield the best estimator the SPTRRE based on Wald test dominates the other two estimators.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.1
• /
• pp.1-7
• /
• 2014

A study on the available power of a wind turbine to be used for wind farm control was performed in this study, To accurately estimate the available power it is important to obtain a suitable wind which represents the three dimensional wind that the wind turbine rotor faces and also used to calculate the power. For this, two different models, the equivalent wind and the wind speed estimator were constructed and used for dynamic simulation using matlab simulink. From the comparison of the simulation result with that from a commercial code based on multi-body dynamics, it was found that using the hub height wind to estimate available power from a turbine results in high frequency components in the power prediction which is, in reality, filtered out by the rotor inertia. It was also found that the wind speed estimator yielded less error than the equivalent wind when compared with the result from the commercial code.

• The Korean Journal of Applied Statistics
• /
• v.17 no.1
• /
• pp.105-117
• /
• 2004

In this paper, a new method is developed for estimating the mean of a population which has a linear trend. This method involves drawing a sample by the modified systematic sampling, and then estimating the population mean with an adjusted estimator, not with the sample mean itself. We use the method of least squares in determining the adjusted estimator. The proposed method is shown to be more and more efficient as the linear trend becomes stronger. It turns out to be relatively efficient as compared with the conventional methods if $\sigma$$^2$the variance of the random error term in the infinite superpopulation model, is not very large.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.4
• /
• pp.318-324
• /
• 2013

For blind channel equalization, the reliability of signal estimate determines the convergence speed and steady-state performance of the equalizer. Therefore the nonlinear estimator and reference signal being used in signal estimate should be chosen appropriately. In this paper, to increase the reliability of the signal estimate, two errors were obtained by applying coarse signal points and dense signal points respectively to signal estimate, the relative reliabilities of two errors were calculated, then the equalizer was adapted deferentially utilizing the reliabilities. At this point, by applying two errors alternately, two modes of operation were smoothly combined. Through computer simulations the proposed method was confirmed to achieve fast transient state convergence and low steady-state error compared to traditional methods.