• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.7 no.2
• /
• pp.209-222
• /
• 1997

Authors surveyed the ground water near the waste disposed from a fiberglass production factory to confirm the presence of glassfiber in the water and to determine the effect of sampling conditions and storage on the recovery of fibrous materials in the ground water. Sample was collected at every 4 hours for 48 hours consecutively. After finishing the 48 hours sample, water sampling was done from each tap after repeated turning on and off the water for 30 seconds at each time. Sample was collected in the two 1.5 liter polyethylene bottle after vigorously shaking the bottle with the same water several times with the flowing tap water. At each paired sample, one bottle was stored stand still at room temperature, and the other sample was filtered immediately after sampling. Water was filtered on the Mixed Cellulose Ester filter with negative pressure. Each sample was divided into upper and lower layer. The other bottle was stored at room temperature standstill for 7 days and filtered in the same fashion as the other pair of sample did. Each MCE filter was divided into 4 pieces and one piece was treated with acetone to make it transparent. Each prepared sample was observed by two researchers under the light and polarizing microscopy, scanning electron microscopy and energy dispersive X-ra microanalysis. Fibers were classified by the morphology and polarizing pattern under the polarizing microscope, and count was done. 1. There was a significant fluctuation in number of the fibers, but there was no specific demonstrable pattern. 2. Non-polarizing fibers frequently disappeared after 7 days's storage. But cluster of fibers were found at the wall of the same container by scratching technique. 3. Polarizing fibers were usually found in between the filter and the manicure pasted area. Possible explanations for this phenomenon will be that either these fibers are very light or have electronic polarity. Hence, these fibers are not able to be attached on the surface of slide glass. 4. Under the scanning electron microscopic examination, the fibers which are not refractive under the light microscopy were identified as glassfiber. Other fibers which is refractive under the polarizing microscopy were identified as magnesium silicate fibers. It is strongly suggested that development of standardized method of sample collection and measurement of fibrous material in the water is needed.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.16 no.2
• /
• pp.136-146
• /
• 1987

Flavor components were trapped by stimultaneous steam distillation-extraction method for investigating it in the bellflower roots and fractionated into four groups such as a neutral, a basic, a phenolic and an acidic fraction. An acidic fraction methylated with diazomethane solution and three others were analysed by GC and GC-MS equipping a fused silica capillary column, and S-containing compounds in these were detected with a flame photometric detector (FPD). The total of one hundred and three compounds from the bellflower roots were identified: they were 6 aliphatic hydrocarbons, 10 aromatic hydrocarbons, 2 terpene hydrocarbons, 12 alcohols, 8 terpene alcohols, 17 aldehydes, 3 terpene aldehydes, 5 ketones, 5 esters, 3 furans, 2 thiazoles, 2 lactones, 2 sulfides, 9 phenols, l2 carboxylic acids and 5 others. The greater part of the others except carboxylic acids were identified from a neutral fraction of which was assumed to be indispensable for the reproduction of bellflower root odor in a sensory evaluation. As a result of a sensory evaluation, 1-hexanal, trans-2-hexenal, 1-hexanol, cis-3-hexenol, trans-2-hexenol, 1-octen-3-ol and so forth identified in a neutral fraction were considered to be the key compounds of grass-like odor in the bellflower roots.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.36 no.3
• /
• pp.332-341
• /
• 2007

The purpose of this study was to investigate the change of flavor compounds of freeze-dried garlic and garlic roasted with soybean oil and sesame oil. Freeze-dried garlic and ground raw garlic roasted with oils was prepared at $180^{\circ}C$ for 5 minutes. Volatile compounds of garlic samples were obtained by Likens-Nickerson distillation/solvent extraction and identified by GC and GC/MS. Sulfur compounds, methyl allyl sulfide, diallyl sulfide, methyl allyl disulfide, dimethyl trisulfide, diallyl disulfide, methyl allyl trisulfide and diallyl trisulfide were the major volatile in garlic flavor which was more than 98% of the total volatile compounds. The total amount of sulfur compounds in freeze-dried garlic roasted with soybean oil was decreased to 20% compare to that of garlic flavor; however, 10 pyrazines such as 2-methyl pyrazine, 2,6-dimethyl pyrazine, 2-ethyl-5-methyl pyrazin and 3-ethyl-2,5-dimethyl pyrazine which were not originated from both freeze-dried garlic and soybean oil were identified. They might be generated from thermal interactions of sugars and nonvolatile flavor precursors of garlic. In freeze-dried garlic roasted with sesame oil, the amount of diallyl sulfide, methyl allyl disulfide, dimethyl trisulfide increased whereas diallyl disulfide completely disappeared. The amount of two cyclic compounds 3,4-dihydro-3-vinyl-1,2-dithiin and 2-vinyl-4H-1,3-dithiin, which were artifacts from allicin, increased in roasted garlic with sesame oil.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.41 no.12
• /
• pp.1701-1707
• /
• 2012

3,3'-Diindolylmethane (DIM) is a major in vivo derivative of the putative anticancer agent indole-3-carbinol, which is present in cruciferous vegetables and has been reported to have anti-carcinogenic properties. An abnorrmally elevated level of cyclooxygenase-2 (COX-2) has been implicated in the pathogenesis of carcinogenesis. To investigate the mechanism by which DIM exhibits anti-carcinogenic effects, we investigated the effects of DIM on COX-2 expression in MCF-10A human mammary epithelial cells treated with the tumor promoter 12-O-tetradecanoylphorbol 13-acetate (TPA). DIM inhibited TPA-induced COX-2 expression and suppressed the synthesis of prostaglandin $E_2$, one of the major products of COX-2. Nuclear factor-kappa B ($NF-{\kappa}B$) is a transcription factor known to play a role in regulation of COX-2 expression. Treatment of MCF-10A cells with TPA increased nuclear translocation of phospho-p65, with the maximal levels being reached at 1 hour, while DIM inhibited the TPA-induced nuclear translocation of phospho-p65. Overall, we demonstrated that DIM suppresses phorbol ester-induced $PGE_2$ production and COX-2 expression in MCF-10A cells. The reduction in COX-2 levels by DIM maybe mediated through inhibition of $NF-{\kappa}B$ signaling.

• Korean Chemical Engineering Research
• /
• v.43 no.5
• /
• pp.621-626
• /
• 2005

The esterification reaction of free fatty acid with methanol was investigated in the presence of catalyst, Amberlyst-15, producing fatty acid methyl ester, namely, biodiesel. In this paper, the effects of the reaction parameters such as reaction temperature, mole ratio of alcohol to oleic acid and mass of catalyst on the catalytic activity have been examined. The results showed that the reaction rate increased about twice as the temperature increased every $20^{\circ}C$ in the reaction temperature range from 333 K to 373 K. The equilibrium conversion rate of oleic acid increased with the feed mole ratio of alcohol to acid ranging from 6:1 to 44:1. When the feed mole ratio was higher than 44:1, all the results were similar to that of 44:1. As for the influence of the mass of catalyst, the initial reaction rate increased from 1.2 to 1.3 times as the mass of catalyst doubles in the range of the catalyst weight from 5 to 20 wt%. The experiment data obtained were well described by the second reaction rate using a pseudo-homogeneous model.

• Journal of the Korea Concrete Institute
• /
• v.19 no.4
• /
• pp.421-431
• /
• 2007

The main purpose of this study is to develop a sprayed FRP repair and strengthening method, which is a new technique for strengthening the existing concrete structures by mixing one of the carbon or glass chopped fibers and one of the epoxy or vinyl ester resins with high-speed compressed air in open air and randomly spraying the mixture onto the concrete surface. At present, the sprayed FRP repair and strengthening method using the epoxy resin has not been fully discussed. In order to investigate the material property of the sprayed FRP, this study carried out tensile tests of the material specimens, which were changed with the combinations of various variables including the length of chopped fiber and the mixture ratio of chopped fiber and resin. These variables were set to have the equal material strength, compared with that of one layer of the FRP sheet. As a result, the optimal length of glass and carbon chopped fibers was fumed out to be 38 mm, and the optimal mixture ratio between chopped fiber and resin was also turned out to be 1 : 2 from each variable. And also, the thickness of the sprayed FRP to have the equal strength to one layer of the FRP sheet was finally calculated. In is study, a series of experiments were carried out to evaluate the strengthening effects of flexural beams, shear beams and damaged beams strengthened with the sprayed FRP method, respectively. The results revealed that the strengthening effects of the flexural and shear specimens were reasonably similar to those of the FRP sheet, and the developed Sprayed FRP technique is able to be used as a strengthening scheme of existing RC building.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.2
• /
• pp.63-67
• /
• 2010

The organic solar cells with Glass/ITO/PEDOT:PSS/P3HT:PCBM/Al structure were fabricated using regioregular poly (3-hexylthiophene) (P3HT) polymer:(6,6)- phenyl $C_{61}$-butyric acid methyl ester (PCBM) fullerene polymer as the bulk hetero-junction layer. The P3HT and PCBM as the electron donor and acceptor materials were spin casted on the indium tin oxide (ITO) coated glass substrates. The optimum mixing concentration ratio of photovoltaic layer was found to be P3HT:PCBM = 4:4 in wt%, indicating that the short circuit current density ($J_{SC}$), open circuit voltage ($V_{OC}$), fill factor (FF) and power conversion efficiency (PCE) values were about 4.7 $mA/cm^2$, 0.48 V, 43.1% and 0.97%, respectively. To investigate the effects of the post annealing treatment, as prepared organic solar cells were post annealed at the treatment time range from 5min to 20min at $150^{\circ}C$. $J_{SC}$ and $V_{OC}$ increased with increasing the post annealing time from 5min to 15min, which may be originated from the improvement of the light absorption coefficient of P3HT and improved ohmic contact between photo voltaic layer and Al electrode. The maximum $J_{SC},\;V_{OC}$, FF and PCE values of organic solar cell, which was post annealed for 15min at $150^{\circ}C$, were found to be about 7.8 $mA/cm^2$, 0.55 V, 47% and 2.0%, respectively.

• Ocean and Polar Research
• /
• v.41 no.4
• /
• pp.265-274
• /
• 2019

To trace the provenance of fine-grained sediments in response to the growth and retreat of glaciers (i.e., Ross Ice Sheet) that affects the depositional process, various kinds of analyses including magnetic susceptibility, granulometry, and clay mineral composition with AMS ¹⁴C age dating were carried out using a gravity core KI-13-GC2 obtained from the Central Basin of the Ross Sea continental margin. The sediments mostly consist of silty mud to sand with ice-rafted debris, the sediment colors alternate repeatedly between light brown and gray, and the sedimentary structures are almost bioturbated with some faint laminations. Among the fine-grained clay mineral compositions, illite is highest (59.1-76.2%), followed by chlorite (12.4-21.4%), kaolinite (4.1-11.6%), and smectite (1.2-22.6%). Illite and chlorite originated from the Transantarctic mountains (metamorphic rocks and granitic rocks) situated to the south of the Ross Sea. Kaolinite might be supplied from the sedimentary rocks of Antarctic continent underneath the ice sheet. The provenance of smectite was considered as McMurdo volcanic group around the Victoria Land in the western part of the Ross Sea. Chlorite content was higher and smectite content was lower during the glacial periods, although illite and kaolinite contents are almost consistent between the glacial and interglacial periods. The glacial increase of chlorite content may be due to more supply of the reworked continental shelf sediments deposited during the interglacial periods to the Central Basin. On the contrary, the glacial decrease of smectite content may be attributed to less transport from the McMurdo volcanic group to the Central Basin due to the advanced ice sheet. Although the source areas of the clay minerals in the Central Basin have not changed significantly between the interglacial and glacial periods, the transport pathways and delivery mechanism of the clay minerals were different between the glacial and interglacial periods in response to the growth and retreat of Ross Ice Sheet in the Ross Sea.

• Applied Chemistry for Engineering
• /
• v.29 no.5
• /
• pp.556-564
• /
• 2018

In this study, polyethylene oxide (PEO)/polyethylene-co-vinyl acetate (EVA)/multi-walled carbon nanotube (MWCNT)-COOH composite membranes were prepared by adding 1, 2, 3, and 5 wt% of MWCNT-COOH to PEO/EVA respectively. The gas permeation properties of $N_2$, $O_2$ and $CO_2$ at $30^{\circ}C$ and 4~8 bar pressure were investigated. In each PEO/EVA/MWCNT-COOH composite membranes, the permeability of $CO_2$ increased with increasing the pressure, but the permeability of $N_2$ and $O_2$ were independent of the feeding pressure. As the MWCNT-COOH content increased, the $CO_2$ permeability increased and then decreased above 2 wt% MWCNT-COOH content. The 2 wt% MWCNT-COOH composite membrane exhibited a $CO_2/N_2$ selectivity of 77.8 and a $CO_2$ permeability of 84 barrer at 8 bar. The high $CO_2/N_2$ selectivity and $CO_2$ permeability were due to the high affinity between the quadrupolar $CO_2$, polar ether groups of PEO, and the polar ester groups of EVA. Additionally, the strong affinity between $CO_2$ and the -COOH groups on the MWCNT surface contributed to the high permeability of $CO_2$.

• Journal of Life Science
• /
• v.8 no.5
• /
• pp.532-536
• /
• 1998

This study was designed to observe the effects of the feeding Gentiana scabra Bunge var.buergeri Max. extract on the improvement of the blood glucose, lipids in the serum of dietary hyperlipidemic rats (S.D. strain, ♂) fed the experimental diets for 4 weeks. Concentration of blood glucose was significantly higher in the cholesterol administration groups (group 2(cholesterol+water), 3(cholesterol+Gentiana scabra Bunge extract) than those in the control group(group 1 (water)). Blood glucose concentration was rather lower in the group 3(cholesterol+Gentiana scabra Bunge extract) than in the group 2(cholesterol+water). There was almost little significance among the groups. Concentration of total cholesterol in serum was significantly lower in the group 3 than those in the group 2. Concentration of LDL-cholesterol in serum was significantly lower in the group 3 than that in the group 2. In the ratio of HDL-cholesterol concentration to total cholesterol concentration, Gentiana scabra Bunge extract administration group was higher percentage than in the group 2. Concentration of free cholesterol and cholesteryl ester in serum was significantly lower in the group 3 than in the group 2. Concentrations of triglyceride and phospholipid in serum were decreased in the group 3 than in the high fat diet group. The activities of aspartate aminotransferase and alanine aminotransferase in serum were increased in the all experimental groups than in the control group. From the above research, the Gentiana scabra Bunge var.buergeri Max. exacts were effective on the improvement of the lipid composition in serum of dietary hyperlipidemic rats.