• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.7 s.238
• /
• pp.930-937
• /
• 2005

One of the useful technology for light-weightening of components required in the automobile and machine industry is to use of high strength materials. To improve material properties, carbonizing treatment, nitrifying treatment, and shot-peening method are representatively applied, However, the shot-peening method is generally used to remove the surface defect of steel and to improve the fatigue strength on surface. Benefits by shot peening are to make increase resistance against fatigue, stress corrosion cracking, fretting, galling, erosion and closing of pores. In this paper, investigated the effect of shot peening on the corrosion of SUP-9 steel immersed in $3.5\%$ NaCl solution and corrosion characteristics by the heat treatment during shot peening process. The immersion test was performed on the four kinds of specimens. Corrosion potential, polarization curve, residual stress and etc. were investigated from the experimental results.

• Journal of Pharmaceutical Investigation
• /
• v.40 no.5
• /
• pp.285-289
• /
• 2010

Manufacturing a multi-layered tablet such as Xatral XL$^{(R)}$ is more complex and expensive than monolayered tablets, but mono-layered tablets may have less favorable release properties depending on the pharmacodynamics and pharmacokinetics of the active ingredient. We therefore sought to develop a monolayer tablet with a similar dissolution profile to the commercial alfuzosin sustained-release triple layered tablet (Xatral XL$^{(R)}$). We prepared four different mono-layered alfuzosin tablets with different concentrations of hydroxypropyl methycellulose and PVP K-90. Fomulation III with alfuzosion/mg-stearate/ HPMC/ PVP K-90 (10/5/110/95 mg/tab) has a similar dissolution rate to Xatral XL$^{(R)}$, with a similarity factor score of 81.4. However, the swelling and erosion rates of the two formulations were different, and NIR analysis showed differences in the mechanisms of drug release. Thus, although formulation III and Xatral XL$^{(R)}$ show similar dissolution rates, the mechanisms of drug release are different.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.2 s.179
• /
• pp.146-153
• /
• 2006

Acceleration sensors have widely been used in the various fields of industry. In recent years, micromachining accelerometers have been developed and commercialized by the micromachining technique or MEMS technique. Typical structure of such sensors consist of a cantilever beam and a vibrating mass fabricated on Si wafers using etching. This study investigates the feasibility of powder blasting technique for microfabrication of sensor structures made of the pyrex glass alternating the existing Si based acceleration sensor. First, as preliminary experiment, effect of blasting pressure, mass flow rate of abrasive and no. of nozzle scanning on erosion depth of pyrex and soda lime glass is studied. Then the optimal blasting conditions are chosen for pyrex sensor. Structure dimensions of designed glass sensor are 2.9mm and 0.7mm for the cantilever beam length and width and 1.7mm for the side of square mass. Mask material is from aluminium sheet of 0.5mm in thickness. Machining results showed that tolerance errors of basic dimensions of glass sensor ranged from 3um in minimum to 20um in maximum. This results imply the powder blasting can be applied for micromachining of glass acceleration sensors alternating the exiting Si based sensors.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.557-562
• /
• 2004

A surface-piercing barrier model is presented for understanding morphological development in the sheltered region and investigating the main factors causing the severe accumulation. Surface-piercing structures like vertical barriers, surface docks and floating breakwaters are recently favored from the point of view of a marine scenario since they do not in general partition the natural sea. The numerical solutions are compared with experimental data on wave profiles and morphological change rates within a rectangular harbor of a constant depth protected by surface-piercing thin breakwaters as a simplified problem. Our numerical study involves several modules: 1) wave dynamics analyzed by a plane-wave approximation, 2) suspended sediment transport combined with sediment erosion-deposition model, and 3) concurrent morphological changes. Scattering waves are solved by using a plane wave method without inclusion of evanescent modes. Evanescent modes are only considered in predicting the reflection ratio against the vertical barrier and energy losses due to vortex shedding from the lower edge of plate are taken into account. A new relationship to relate the near-bed concentration to the depth-mean concentration is presented by analyzing the vertical structure of concentration. The numerical solutions were also compared with experimental data on morphological changes within a rectangular harbor of constant water depth. Through the numerical experiments, the vortex-induced flow appears to be not ignorable in predicting the morphological changes although the immersion depth of a plate is not deep.

• Korean Journal of Hydrosciences
• /
• v.10
• /
• pp.73-83
• /
• 1999

The intake towers of Buyeo W.T.P. in Keum river have being suffered from the sedimentation problems since the beginning of the operation. Impellers of the intake pumps have to the frequently changed due to the serious surface erosion. Thousands tons of sands are entrapped in the intake towers and equalization chambers of W.T.P. every year. Site surveying and numerical analysis were carried out to suggest an appropriate solution by understanding the general sedimentation regime of Keum river and causes of the sedimentation in the intake towers. Origin of the sediment could be found by the desk and site inspections. The validity of the used numerical models was examined by comparisons between the calculated bydraulic values and the measured ones during the specific periods. The design flow rate for the prediction of the future sedimentation regime of the rever was studied. The efficiency of the sediment control measures was also examined with the verified numerical models. Finally, it was found that the best solution could be a combination of three sediment control measures; increase the clearance between river bed and inlet, construct jetties at 2 kilometers upstream from the intake towers, and put vanes at the right side of the intake towers.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.5 no.2
• /
• pp.277-286
• /
• 2013

Cross-shore sediment transport is very important factor in the design of coastal structures, and the beach profile is mainly affected by a number of parameters, such as wave height and period, beach slope, and the material properties of the bed. In this study cross-shore sediment movement was investigated using a physical model and various offshore bar geometric parameters were determined by the resultant erosion profile. The experiments on cross- shore sediment transport carried out in a laboratory wave channel for initial base slopes of 1/8, 1/10 and 1/15. Using the regular waves with different deep-water wave steepness generated by a pedal-type wave generator, the geometrical of sediment transport rate and considerable characteristics of beach profiles under storm conditions and bar parameters affecting on-off shore sediment transport are investigated for the beach materials with the medium diameter of $d_{50}$=0.25, 0.32, 0.45, 0.62 and 0.80 mm. Non-dimensional equations were obtained by using linear and non-linear regression methods through the experimental data and were compared with previously developed equations in the literature. The results have shown that the experimental data fitted well to the proposed equations with respect to the previously developed equations.

• Journal of Korean Society of Forest Science
• /
• v.23 no.1
• /
• pp.35-39
• /
• 1974

After lasting heavy storm, the overfow from the top of soil saving dam may follow if the outlet is not precisely designed and it causes great damages as a result. Therefore, the peak rate of flood must be premeditated at the time of dam construction and many kinds of erosion control measures should also be constructed to protect against the effects of oveflow causing the damages. In this paper, the daily maximum amounts of precipitation from 1904 to 1972 are used as samples of this statistical analysis for the previous purpose and studying local ranges are limited the number of areas to two; Pusan and Mokpo area, because other areas can not give the data of more than 69 years. Normal distribution, as follows, is used for this statistical study. $$P(X)=\int_{x}^{{\infty}}f(x)dx$$ x: daily maximum amount X: maximum of x P(X): probability to exceed X value The estimates, which are the resultants of statistical analysis, can be locally compared with the real values (daily maximum amounts) by diagram, whether the former truly coincides with the latter. As a result, statistical method canot be used for the premeditation of the amount as well as timing of heavy storms because the estimates donot coincide with the real values in this analysis.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.3
• /
• pp.131-137
• /
• 2006

The secondary system of nuclear power plants consists of sophisticated piping systems operating in very aggressive erosion and corrosion environments, which make a piping system vulnerable to the wear and degradation due to the several chemical components and high flow rate (~10 m/sec) of the coolant. To monitor the wear and degradation on a pipe, the vibration signals are measured from the pipe with an accelerometer For analyzing the vibration signal the time-frequency analysis (TFA) is used, which is known to be effective for the analysis of time-varying or transient signals. To reduce the inteferences (cross-terms) due to the bilinear structure of the time-frequency distribution, an adaptive cone-kernel distribution (ACKD) is proposed. The cone length of ACKD to determine the characteristics of distribution is optimally selected through an adaptive algorithm using the normalized Shannon's entropy And the ACKD's are compared with the results of other analyses based on the Fourier Transform (FT) and other TFA's. The ACKD shows a better signature for the wear/degradation within a pipe and provides the additional information in relation to the time that any analysis based on the conventional FT can not provide.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2032-2034
• /
• 2000

The performance of ac plasma display panels (PDP) is influenced strongly by the surface glow discharge characteristics on the MgO thin films. This paper deals with the surface slew discharge characteristics and some physical properties of MgO thin films prepared by reactive RF planar unbalanced magnetron sputtering in connection with ac PDP. The samples prepared with the do bias voltage of -10V showed lower discharge voltage and lower erosion rate by ion bombardment than those samples prepared by conventional magnetron sputtering or E-beam evaporation. The main factor that improves the discharge characteristics by bias voltage is considered to be due to the morphology changes or crystal structure of the MgO thin film by ion bombardment during deposition process.

• Korean Journal of Materials Research
• /
• v.26 no.3
• /
• pp.123-129
• /
• 2016

The morphology, crystal structure and size of aerosol nanoparticles generated by erosion of electrodes made of different materials (titanium, copper and aluminum) in a multi-spark discharge generator were investigated. The aerosol nanoparticle synthesis was carried out in air atmosphere at a capacitor stored energy of 6 J, a repetition rate of discharge of 0.5 Hz and a gas flow velocity of 5.4 m/s. The aerosol nanoparticles were generated in the form of oxides and had various morphologies: agglomerates of primary particles of $TiO_2$ and $Al_2O_3$ or aggregates of primary particles of $Cu_2O$. The average size of the primary nanoparticles ranged between 6.3 and 7.4 nm for the three substances studied. The average size of the agglomerates and aggregates varied in a wide interval from 24.6 nm for $Cu_2O$ to 46.1 nm for $Al_2O_3$.