• Structural Engineering and Mechanics
• /
• v.72 no.1
• /
• pp.83-97
• /
• 2019

In this research, the vulnerability of some reinforced concrete frames with different stories are studied based on the Park-Ang Damage Index. The damages of the frames are investigated under various earthquakes with nonlinear dynamic analysis in IDARC software. By examining the most important characteristics of earthquake parameters, the damage index and vulnerability of these frames are investigated in this software. The intensity of Erias, velocity spectral intensity (VSI) and peak ground velocity (PGV) had the highest correlation, and root mean square of displacement ($D_{rms}$) had the lowest correlation coefficient among the parameters. Then, the particle swarm optimization (PSO) algorithm was used, and the sinusoidal waves were equivalent to the used earthquakes according to the most influential parameters above. The damage index equivalent to these waves is estimated using nonlinear dynamics analysis. The comparison between the damages caused by earthquakes and equivalent sinusoidal waves is done too. The generations of sinusoidal waves equivalent to different earthquakes are generalized in some reinforced concrete frames. The equivalent sinusoidal wave method was exact enough because the greatest difference between the results of the main and artificial accelerator damage index was about 5 percent. Also sinusoidal waves were more consistent with the damage indices of the structures compared to the earthquake parameters.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.4B no.4
• /
• pp.206-210
• /
• 2004

This paper deals with a parameter estimation of the DC-DC converter system for its diagnosis. Especially, we present the results of parameter estimation for the DC-DC converter model by the system identification method. The parameter estimation for the DC-DC converter system aims at the diagnosis of its operating status. For the operating status diagnosis of the DC-DC converter system, we assume that the DC-DC converter system is an equivalent model of the Buck converter and estimate the main parameter for on-line diagnosis. In addition, for verification of an estimated parameter, we compare a bode plot of the estimated system transfer function and measurement results of the HP4194 instrument. It is a control system analyzer for system transfer function measurement. Our results confirm that the main parameter for diagnosis of the DC-DC converter system can be estimated by the system identification method and that the aging status of the system can be predicted by these results on operating status.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.12
• /
• pp.59-65
• /
• 2014

Two input resistances converted from $S_{11}$-parameter and $Z_{11}$-parameter of MOSFETs with various gate finger numbers Nf were measured in low frequency region. The 1/Nf dependent input resistance from $S_{11}$-parameter exhibits much lower values than that from $Z_{11}$-parameter in the range of $Nf{\leq}64$. This 1/Nf dependence was theoretically verified by using Nf dependent nonlinear equation derived from a MOSFET equivalent circuit.

• 전기의세계
• /
• v.31 no.2
• /
• pp.126-131
• /
• 1982

Induction motors are known to cause voltage dip, oscillating torque and inrush current on the dynamic period. To compensate for these undesirable effects, the prediction of dynamic performances is required. The dynamic performances are determinated by circuit time constants. From this point of view, in this paper, the dynamic equivalent circuit included only three time-constant parameters are presented. To predict more simply dynamic performances, the new characteristics time constant parameters are analyzed, and now these parameters are described as the function of circuit time constants. This paper reviews and analyzes the use of series capacitance compensations, and the use of this analysis can make simply a prediction about oscillating conditions.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.748-753
• /
• 1998

Machine parameters need to measure in advance for vector control and theoretical analysis. Therefore, we present the machine parameter measurement scheme, considering stator iron loss, by the single-phase test at standstill condition. Using this method, the d-q axis inductances and the equivalent iron loss resistance in the voltage equation considering stator iron loss are easily measured. This method is simple and does not need to use complex theory and expensive equipment.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.2
• /
• pp.160-164
• /
• 2010

The radio frequency (RF) model of SOI FinFETs with gate length of 40 nm is verified by using a 3-dimensional (3-D) device simulator. This paper shows the equivalent circuit model which can be used in the circuit analysis simulator. The RMS modeling error of Y-parameter was calculated to be only 0.3 %.

• Journal of the Korean Magnetics Society
• /
• v.26 no.2
• /
• pp.55-61
• /
• 2016

This study proposes the design algorithm of an electromagnetic linear actuator with a divided coil excitation system, such as the colenoid (COL) system, using the equivalent magnetic circuit (EMC) method. Nowadays, the clamping device is used to hold workpiece in the electrically driven chucking system and is needed to produce a huge clamping force of 40 kN like hydraulic system. The design algorithm for electromagnetic linear actuator can be obtained using the EMC method. At first, the parameter map is used to decide the slot width ratio in the initial design. Next, to make the magnetic flux density uniform at each pole, the pole width is adjusted by the pole width adjusting algorithm with EMC. When the dimensions of the electromagnetic linear actuator are decided, the clamping force is calculated to check the desired clamping force. The design results show that it can be used to hold a workpiece firmly instead of using a hydraulic cylinder in a chucking system.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.4
• /
• pp.629-635
• /
• 2017

Free-Flooded Ring (FFR) transducer array for use in Sonar system can be driven with large amplitude in a wide frequency band due to its structural characteristics, in which two resonances of a ring mode (1st radial mode) and an inner cavity vibration mode occur in a low frequency band. Since its sound wave generation characteristics are not influenced by the water pressure, the FFR transducer array is widely used in the deep sea. So FFR has been recognized as a low-frequency active sound source and has received much attention ever since. In order to utilize the FFR transducer array for SONAR systems in military and industrial applications, its equivalent electric circuit model is necessary especially to design the matching circuit between the driving power amplifier and the FFR transducer array. Thus this paper proposes the equivalent electric circuit model of FFR transducer array by using measured values of parameter, and suggest the improved method of parameter identification. Finally it verifies the effectiveness of the proposed circuit model of FFR transducer array by experimental measurements.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.3
• /
• pp.289-297
• /
• 2014

This paper proposed a novel high performance sensorless control scheme for IPMSM based on an extended nonlinear state observer. The gain-matrix of the observer has been derived by using state linearization method. Steady state errors in estimated rotor position and speed due to parameter inaccuracy have been analyzed, and an equivalent flux error is defined to represent the overall effect of parameter errors contributing to the wrong convergence of the estimated rotor speed as well as rotor position. Then, an online compensation strategy was proposed to limit the estimation errors in rotor position and speed. The effectiveness of the extended nonlinear state observer is validated through simulation and experimental test.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.3
• /
• pp.227-234
• /
• 2020

This paper presents the methods for the modeling and parameter optimization of the electric vehicle battery. The state variables of the battery are defined, and the test methods for battery parameters are presented. The state-space equation, which consists of four state variables, and the output equation, which is a combination of to-be-determined parameters, are shown. The parameter optimization method is the key point of this study. The least square of the modeling error can be used as an initial value of the multivariable function. It is equivalent to find the minimum value of the error function to obtain optimal parameters from multivariable function. The SIMULINK model is presented, and the 10-hour full operational range test results are shown to verify the performance of the model. The modeling error for 25 degrees is approximately 1% for full operational ranges. The comments to enhance modeling accuracy are shown in the conclusion.