• Smart Structures and Systems
• /
• v.14 no.2
• /
• pp.247-266
• /
• 2014

Conventional cantilevered piezoelectric energy harvesters (PEHs) are usually fabricated with continuous electrode configuration (CEC), which suffers from the electrical cancellation at higher vibration modes. Though previous research pointed out that the segmented electrode configuration (SEC) can address this issue, a comprehensive evaluation of the PEH with SEC has yet been reported. With the consideration of delivering power to a common load, the AC outputs from all segmented electrode pairs should be rectified to DC outputs separately. In such case, theoretical formulation for power estimation becomes challenging. This paper proposes a method based on equivalent circuit model (ECM) and circuit simulation to evaluate the performance of the PEH with SEC. First, the parameters of the multi-mode ECM are identified from theoretical analysis. The ECM is then established in SPICE software and validated by the theoretical model and finite element method (FEM) with resistive loads. Subsequently, the optimal performances with SEC and CEC are compared considering the practical DC interface circuit. A comprehensive evaluation of the advantageous performance with SEC is provided for the first time. The results demonstrate the feasibility of using SEC as a simple and effective means to improve the performance of a cantilevered PEH at a higher mode.

• ETRI Journal
• /
• v.28 no.3
• /
• pp.347-354
• /
• 2006

The characteristic variation of 3-dimensional (3-D) solenoid-type embedded inductors is investigated. Four different structures of a 3-D inductor are fabricated by using a low-temperature co-fired ceramic (LTCC) process, and their s-parameters are measured between 50 MHz and 5 GHz. The circuit model parameters of each building block are optimized and extracted using the partial element equivalent circuit method and an HSPICE circuit simulator. Based on the model parameters, the characteristics of the test structures such as self-resonant frequency, inductance, and quality (Q) factor are analyzed, and predictive modeling is applied to the structures composed of a combination of the modeled building blocks. In addition, characteristic variations of the 3-D inductors with different structures using extracted building blocks are also investigated. This approach can provide a characteristic estimation of 3-D solenoid embedded inductors for structural variations.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.772_773
• /
• 2009

A numerically efficient performance analysis method for Thomson coil actuator of an arc eliminator is developed by transferring the problem to an equivalent circuit model considering the distribution of eddy current in conducting plate. Through a numerical analysis, the developed method is proven to give a solution, with only 1.3% of computing time, as accurate as finite element method. The developed method is testified by comparing with FEM calculation and experiment results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.11
• /
• pp.58-66
• /
• 2011

In this paper, the starting torque and efficiency characteristics of the induction motor (IM) for the electric vehicle (EV) are improved by changing the slot shapes of squirrel cage. The initial model of the induction motor is designed by the loading distribution method (LDM), and then the rotor with squirrel cage of NEMA class A is selected to optimize the slot shape by response surface method(RSM). The design variables of rotor slot shape are obtained by the RSM. Starting torque and efficiency were calculated by the equivalent circuit method. As a result, starting torque and efficiency of the optimized model shows good performance through whole-speed range.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.8
• /
• pp.1180-1185
• /
• 2015

This paper describes the accurate inductance measurement of a switched reluctance motor (SRM). Conventionally, the inductance of the SRM is measured using the equivalent circuit of a stator phase or time constant of exponential current transient. This paper presents an effective method to measure the SRM inductance accurately and rapidly using automated voltage integration. The proposed method is validated experimentally by comparison with the existing equivalent circuit method (ECM) and the FEA(finite element analysis) simulation.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.3
• /
• pp.330-335
• /
• 2012

The shape optimization of a Thomson coil actuator used in an arc eliminator is done for fast response by adopting topology modification method. The displacement of the plate in a fixed calculation time is taken as the objective function. The objective function and contribution factor are calculated by using an adaptive equivalent circuit method which has been proved accurate and efficient. Both shape optimization and performance analysis are accomplished based on the segmentation of plate. Through the refinement of the sensitive segments a precise optimal plate shape can be obtained. The effectiveness of the proposed method is proved by the comparison of results before and after the shape optimization.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.1
• /
• pp.58-63
• /
• 2012

The shape optimization of a Thomson coil actuator used in an arc eliminator is done for fast response by adopting topology modification method. The displacement of the plate in a fixed calculation time is taken as the objective function. The objective function and contribution factor are calculated by using an adaptive equivalent circuit method which has been proved accurate and efficient. Both shape optimization and performance analysis are accomplished based on the segmentation of plate. Through the refinement of the sensitive segments a precise optimal plate shape can be obtained. The effectiveness of the proposed method is proved by the comparison of results before and after the shape optimization.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.3
• /
• pp.311-316
• /
• 2015

This paper presents a design method for thin but wideband absorbers using resistive sheets. Its equivalent circuit consists of a series RLC resonant circuit and a short-terminated transmission line. Based on this equivalent circuit, we presented the three conditions for an electromagnetic absorber which has a thickness less than a quarter wavelength and wide absorption bandwidth at center frequency. By using an root-finding algorithm, the equivalent resistance, capacitance, and inductance of the absorbers are obtained. These equivalent circuit values for the absorber surface can be realized by a 2D periodic cross-shaped structure which has required surface resistance. Using the design method, we have designed the absorber which has 18.75 mm($67.5^{\circ}$ electrical length) thickness and 90 % absorption bandwidth of 116 % bandwidth at 3 GHz.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.5
• /
• pp.325-331
• /
• 2004

The multiobjective optimization (MO) problem usually includes the conflicting objectives and the use of conventional optimization algorithms for MO problem does not so good approach to obtain an effective optimal solution. In this paper, genetic algorithm (GA) as an effective method is used to solve such MO problem of brushless DC motor (BLDCM). 3D equivalent magnetic circuit network (EMCN) method which enables us to reduce the computational burden is also used to consider the 3D structure of BLDCM. In order to effectively obtain a set of Pareto optimal solutions in MO problem, ranking method proposed by Fonseca is applied. The objective functions are decrease of cogging torque and increase of torque respectively. The airgap length, teeth width and magnetization angle of PM are selected for the design variables. The experimental results are also shown to confirm the validity of the optimization results.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.794_795
• /
• 2009

This paper presents an analysis method for a permanent magnet excited Transverse Flux Linear Motor (TFLM) with spiral core in a mover. The spiral core is used as mover core in order to make 3-dimensional magnetic flux path at the TFLM which has 3-dimensional magnetic flux flow. Magnetic field is analyzed by three-dimensional Equivalent Magnetic Circuit Network (EMCN) method. And an imaginary part, 'flux barrier,' is introduced to consider the spiral core characteristic. The computed thrust forces is compared to the measured results to show the effect of presented analysis method.