• Journal of Environmental Science International
• /
• v.13 no.4
• /
• pp.421-427
• /
• 2004

With the help of mechanical mixing method such as Banbury mixer and open 2 roll mill, ethylene propylene diene terpolymer (EPDM) was blended with the chloroprene rubber (CR) then mechanical properties and ozone resistance test of blends were subsequently investigated. It was noted that the hardness increased with an increasing of CR contents. Generally the hardness was increased with heat aging time most likely due to the post cure. In ozone resistance test of blend, after 8 hours a portion of fine crack is obtained for pure CR. It is confirmed that ozone resistance is greatly improved by addition of 25wt% EPDM to CR.

• Computers and Concrete
• /
• v.17 no.6
• /
• pp.703-721
• /
• 2016

A novel approach to modeling concrete behavior at the stage of its maturing is presented in this paper. This approach assumes that at any point in the structure, concrete is composed of a set of layers that are activated in time layer by layer, based on amount of released heat that is produced during process of the concrete's maturing. This allows one to assume that each newly created layer has nominal stiffness moduli and tensile/compressive strengths. Hence introduction of explicit stiffness moduli and tensile/compressive strength dependencies on time, or equivalent time state parameter, is not needed. Analysis of plain concrete (PC) and reinforced concrete (RC) structures, especially massive ones, subjected to any kind of straining in their early stage of existence, mostly due to external loads but especially by thermal loading and shrinkage, is the goal of the approach. In this article a simple elasto-plastic softening model with creep is used for each layer and a general layered model behavior is illustrated on one-dimensional (1D) examples.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.737-742
• /
• 2002

The chief factors for the penetration and diffusion of chloride ions in concrete are water-cement ratio(w/c), aging, thickness of cover concrete, chloride ions concentration of given environment, wet and dry conditions and etc. In this study, effect of w/c and aging on the characteristics of chloride ions diffusion in concrete were researched when environmental factors for the penetration and diffusion of chloride ions were constant. For this purpose, the voltages passing through the diffusion cell were measured by using accelerated test method using potential difference, and then diffusion coefficients of chloride ions by using Andrade's method were estimated for 44%, 49.5% and 55% of w/c, respectively. As a result, correlation among diffusion coefficients of chloride ions, w/c and aging were concluded through multiple regression model.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.149-152
• /
• 2001

In this paper, aging diagnosis method of CV cable was investigated. CV cable was designed for the sake of using during 30 years. Therefore it was important to evaluate the cable's remaining life because CV cable used for power transmission line since 1970's. CV cable was mainly installed at the underground owing to the environmental condition. If the cable accident occurred, it needs the much time for the accident recovery and the much damage at the industrial activity. therefore, this paper should study the direct leakage current method, a sort of the cables' aging test method

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.214-217
• /
• 1999

Polymeric composite insulators have been in use for outdoor insulation. However, our knowledge about their long-term performance in a outdoor environment is still very limited. Especially, these insulator are subjected to the environmental stress such as ultraviolet radiation. Hence, in this paper. the influence of UV radiation on the aging of the shed materials was evaluated. For the aging evaluation, these insulators studied by experiment methods such as contact angle measurement. oxidation induced time. SEM/EDX, FTRI-ATR, tracking test for the different insulator samples. With the increased UV exposure time, samples are shown to exhibit degradation comparable to those of new ones

• Steel and Composite Structures
• /
• v.25 no.1
• /
• pp.93-104
• /
• 2017

In the present work, the effect of hygrothermal aging on the glass fibre and epoxy matrix interface has been investigated by destructive and non-destructive techniques. The glass fiber reinforced polymer (GFRP) composite laminates were prepared using Vacuum Assisted Resin Infusion Molding (VARIM) technique and the specimens were immersed in simulated seawater, followed by quantitative measurement. Besides this, the tensile tests of GFRP specimens revealed a general decrease in the properties with increasing aging time. Also, exposed specimens were characterized by a non-destructive ultrasonic guided Lamb wave propagation technique. The experimental results demonstrate a correlation between the drop in ultrasonic voltage amplitude and fall in tensile strength with increasing time of immersion. Hence, the comparison of the transmitted guided wave signal of healthy vis-a-vis specimens subjected to different extents of hygrothermal aging facilitated performance evaluation of GFRP composites.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.149-152
• /
• 2001

In this paper, aging diagnosis method of CV cable was investigated. CV cable was designed for the sake of using during 30 years. Therefore it was important to evaluate the cable's remaining life because CV cable used for power transmission line since 1970's. CV cable was mainly installed at the underground owing to the environmental condition. If the cable accident occurred, it needs the much time for the accident recovery and the much damage at the industrial activity. therefore, this paper should study the direct leakage current method, a sort of the cables'aging test method.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.4
• /
• pp.523-530
• /
• 2019

Pavement distress and traffic accidents are caused by pot-hole. In addition, direct and indirect damages of road users are increasing, such as loss of life due to personal injury and damage to vehicles. Generally, the asphalt concrete pavements are continuously aging from the production process to the terminal performance period. Aging causes stripping due to cracks and moisture penetration and weakening the pavement structure to induce pot-hole. In this study, adhesion performance and moisture sensitivity were evaluated according to aging degree in order to investigate the effect of aging on asphalt pavement. As a result of the study, the viscosity of the asphalt binder was increased with aging and the bond strength of the aged was increased 2~3 times than that of the unaged. The results of accelerated aging test showed an increases in indirect tensile strength and the increase in the TSR (Tensile Strength Ratio) by 4.2~8.9 %. As a result, it is noted that the anti-stripping and adhesion performances of the aged asphalt concrete are improved compared to the unaged one under the aging conditions of asphalt binder coated on aggregates.

• Environmental Analysis Health and Toxicology
• /
• v.23 no.2
• /
• pp.119-127
• /
• 2008

The purpose of this study was to investigate the effects of frankincense oil in a skin aging animal model. Skin aging was induced by both the irradiation of UVB and the application of squalene monohydroperoxide (Sq-OOH) to the back of experimental animals for 4 weeks. And at the same time experimental materials were applied topically. Six to seven weeks female SHR-1 hairless mice were divided into five groups including normal (N: saline), control (C: UVB+Sq-OOH+saline), vehicle control (VC: UVB+Sq-OOH+jojoba oil), positive control (PC: UVB+Sq-OOH+0.01% retinoic acid) and experimental (E: UVB+Sq-OOH+3% Frankincense oil) groups, five animals each group. The skin erythema index for the PC and E groups were lower than that of the C group. Whereas, both the lipid and water capacities for the PC and E groups were higher than those of the C group. Wrinkles for the C group were formed as a pattern of deep furrows and thick crests. Whereas, wrinkles for the PC and E groups were formed as a pattern of shallow furrows and thin crests which were similar to that of the N group. As for the both absolute and relative weight of the spleen, the PC group were significantly higher than the other groups. In conclusion, frankincense oil can be used practically for the prevention or improvement of skin aging in terms of health promotion and beauty for the people.

• Nuclear Engineering and Technology
• /
• v.54 no.11
• /
• pp.4111-4124
• /
• 2022

The control rod drive system is critical to the reactor's reliable operation. The performance of its control system and mechanical system will gradually deteriorate because of operational and environmental stresses, thus increasing the reactor's operational risk. Currently there are few researches on the aging-related degradation of the entire control rod drive system. Because it is difficult to quantify the effect of various environmental stresses and establish an accurate physical model when multiple mechanisms superimposed in the degradation process. Therefore, this paper investigates the aging-related degradation of a control rod drive system by integrating Dynamic Object-Oriented Bayesian Network and Hidden Markov Model. Uncertainties in the degradation of the control system and mechanical system are addressed by using fuzzy theory and the Hidden Markov Model respectively. A system which consists of eight control rod drive mechanisms divided into two groups is used to demonstrate the method. The aging-related degradation of the control rod drive system is analyzed by the Bayesian inference algorithm based on the accelerated life test data, and the impact of different operating schemes on the system performance is also investigated. Meanwhile, the components or units that have major impact on the system's performance are identified at different operational phases. Finally, several essential safety measures are suggested to mitigate the risk caused by the system degradation.