• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.6
• /
• pp.583-590
• /
• 2009

An engine is one of the most dominant noise and vibration sources in vehicle systems. Therefore, in order to resolve noise and vibration problems due to engine, various types of engine mounts have been proposed. This work presents a new type of active engine mount system featuring a magneto-rheological (MR) fluid and a piezostack actuator. As a first step, six degrees-of freedom dynamic model of an in-line four-cylinder engine which has three points mounting system is derived by considering the dynamic behaviors of MR mount and piezostack mount. In the configuration of engine mount system, two MR mounts are installed for vibration control of roll mode motion whose energy is very high in low frequency range, while one piezostack mount is installed for vibration control of bounce and pitch mode motion whose energy is relatively high in high frequency range. As a second step, linear quadratic regulator (LQR) controller is synthesized to actively control the imposed vibration. In order to demonstrate the effectiveness of the proposed active engine mount, vibration control performances are evaluated under various engine operating speeds(wide frequency range) and presented in time domain.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.10a
• /
• pp.319-325
• /
• 1997

As customer's demand for vehicle comfort is getting increased, vibration problem is very important issue in vehicle development. Engine is the main factor causing vehicle vibration, so that we should isolate detrimental transmitted excitation from engine. In order to solve this problem engine mounting system was properly optimized. Simulation was performed not only rigid body mode analysis but also flexible body mode analysis. We obtained the optimal locations and stiffness of engine mounts from simulation results, and had reasonable results from considering flexible body mode than only rigid body mode analysis.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.1
• /
• pp.46-52
• /
• 2012

Since the engine and reduction gear in a naval vessel are usually supported by the mounting system separately, the misalignment between the input shaft of the reduction gear and the output shaft of the engine should occur caused by ship motion. In this study, this misalignment is estimated from the linear static analysis assuming that the phase of movements of the engine and reduction gear at low frequency range is same and the dynamic effect is not affect to them. Through comparing the relative displacement of the engine and reduction gear calculated from linear static analysis to that from dynamic analysis as well as experiment, the assumption in this study could be verified.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1877-1882
• /
• 2000

In this paper, an integrated system for dynamic analysis and optimal design of engine mount systems is presented. The system can simulate static and dynamic behaviors of engine mount systems and optimize design parameters such as mount stiffness, mounting locations with desired design targets of frequency or displacement. A FF-engine with an automatic transmission is used to demonstrate the analysis and optimal design capabilities of the proposed design system.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.3
• /
• pp.235-241
• /
• 2010

Engine Mount plays an important role which supports engine, isolates vibration from engine and blocks the vibration from road. Development of engine mount for NVH costs great a deal. So, the cost of development being reduced, the way developed effectively engine mount using DFSS technique is proposed in this paper. CTQ(critical to quality) is vibration and parameter is dynamic stiffness of mounts. The core parameters are selected with TPA(transfer path analysis) technique. It uses design of experiments(DOE) or Taguchi Methods to optimize parameter values and reduce variation. And then, this paper shows the result of improvement for vibration in the developing vehicle.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.195.1-195.1
• /
• 2005

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.512-513
• /
• 2011

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1991.04a
• /
• pp.139-144
• /
• 1991

4WD자동차의 엔진마운트 설계기법의 정리 및 실제차량의 실험적 mode 해 석을 통해 다음과 같은 결론을 얻었다. 1. 4WD자동차의 엔진마운트 설계 개념을 체계화시키고, 이를 실제차량에 대 해서 실험적 mode해석을 해본 결과 잘 일치함을 확인하였다. 2. power transmission system에 부가되는 장치(front propeller shaft)의 영 향을 검토한바, frequency shift현상이 발생함을 확인하였다. 이러한 영향은 이들 부가장치들의 질량증가 및 관성모멘트의 변화로 기인되며, 질량의 증가 보다는 관성모멘트의 영향이 상대적으로 크리라 판단된다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.328-329
• /
• 2009

Air-Damping Mount is proposed to compromise between performance and weight & cost. The design of Air-Damping Mount was based on the specification from the engine mounting system analysis of a small car. To verify it's feasibility, R&H test was done on the small car and it is proven that Air-Damping Mount shows the performance between hydraulic mount and rubber mount.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1993.04a
• /
• pp.80-85
• /
• 1993

본 논문에서는 디젤 엔진의 탄성지지계에 작용하는 엔진 기진력에 대하여 검토하고, 탄성지지계의 진동 양상과 탄성지지를 통하여 선체로 전달되는 힘 을 계산하는 과정을 정식화하였다. 또한 이 결과를 고무형 탄성지지를 갖는 선박 추진용 디젤엔진과 발전기용 디젤엔진에 적용하여 탄성지지계의 자유 진동과 강제진동 해석을 수행하고 발전기용 디젤엔진의 탄성지지계에 대해 서는 계측을 행하여 계산 결과와의 비교 검토를 행하고자 한다.