• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.138-143
• /
• 2006

Modification of injector, oil ring tension reduction and oil pump rotor re-matching with optimization of relevant engine control parameters could drive fuel consumption reduction of HSDI diesel engine. A 5 holes injector was replaced with a 6 holes with smaller nozzle hole diameter and 1.5 k factor, and evaluated in a view of fuel economy and emission trade-offs. With introducing smaller nozzle hole diameter injector, PM(Particulate Matter) was drastically decreased for low engine load and low engine rpm. Modification of oil pump and oil ring was to reduce mechanical friction and be proved to better fuel economy. Optimization of engine operating conditions was a great help for the low fuel consumption. Influence of the engine operating parameters· including pilot quantity, pilot interval, air mass and main injection timing on fuel economy, smoke and NOx has been evaluated with 14 points extracted from NEDC(New European Driving Cycle) cycle. The fuel consumption was proved to $7\%$ improvement on an engine bench and $3.7\%$ with a vehicle.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.1
• /
• pp.74-80
• /
• 2016

Due to the increased use of power caused by industrial development, the importance of improving wear and friction in the contact region has emerged. Except for some parts, such as brakes or clutches and friction, seals and precision mechanical parts (e.g., pistons, bearings, valves, and cams) are important engine components that require low friction characteristics. In this study, the experimental method used to determine the friction characteristics was based on the type of rpm with the pin-on-disc test device, the element analysis program ANSYS was used to analyze the surfaces of the two metals rubbing together, and physical formation FEM models were used to study the properties and wear. The friction coefficient of variation was unsafe, but at the start of wear, it converged to a stable friction coefficient that increased after a certain slip away.

• Journal of Power System Engineering
• /
• v.16 no.6
• /
• pp.11-18
• /
• 2012

대형 상용 엔진에서 발생하는 유효 도시 마력의 약 4~15%는 마찰 손실을 통해서 사라지며 마찰 손실 중 약 40~55%는 엔진 실린더와 피스톤 사이의 마찰에 의하여 발생하여, 엔진 전체에서 발생하는 마찰 손실 중 가장 많은 부분을 차지하고 있다. 이 연구에서는 엔진 실린더 라이너의 온도 분포 개선을 통해 라이너를 따라 유막을 형성하고 있는 윤활유의 적정 점성을 유지시키는 방법을 제시하고자 한다. 피스톤-라이너에서 발생하는 마찰 특성은 피스톤의 행정 위치에 따라서 접촉 마찰과 유막에 의한 마찰로 구분되며 이에 따라 요구되는 윤활유의 점성 특성 또한 달라진다. 먼저 해석 모델을 통하여 실린더 라이너 내부 온도 분포 특성을 확인한 후 피스톤 마찰 특성을 고려한 적정 온도 분포를 고찰하며 실린더 라이너에 열저항 코팅을 통해서 이를 구현하였다. 또한 실린더-피스톤 간의 마찰/윤활 해석을 통하여 열저항 코팅의 마찰 개선효과를 확인하였다.

• International Journal of Automotive Technology
• /
• v.2 no.2
• /
• pp.47-52
• /
• 2001

For the wear protection of cylinder bore in aluminum cast material the internal plasma spraying technology offers a new economical solution. The size and the weight of the engine blocks significantly can be decreased in comparison with the traditional cast iron sleeves. The coefficient of friction between piston ring and cylinder wall sensitively can be reduced and the wear resistance increased from several factors. The paper gives an overview of the technology from the AlSi cast alloys for engine block to the non destructive testing technology used after the machining by diamond honing. The actual results in engines of different types also will be shown. The economical advantages of the plasma spraying (or the internal coating in cylinder bore also will be discussed in comparison with the different alternatives of technology. The aspect of the market introduction also will be discussed in this paper.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.203-210
• /
• 2003

A simulation study was carried to analyze the vehicle fuel consumption on component basis. Experiments was also carried out to identify the simulation results, under FTP-75 Hot Phase driving conditions. and arbitrary driving conditions. A good quantitative agreement was obtained. Based on the simulation, fuel energy was used in pumping loss(3.7%), electric power generation(0.7%), engine friction(12.7%), engine inertia(0.7%), torque converter loss(4.6%), drivetrain friction(0.6%), road-load(9.2%), and vehicle inertia(13.4%) under FTP-75 Hot Phase driving conditions. Using simulation program, the effects of capacity factor and idle speed on fuel consumption were estimated. A increment of capacity factor of torque converter resulted in fuel consumption improvement under FTP-75 Hot Phase driving conditions. Effect of a decrement of idle speed on fuel consumption was negligible under the identical driving conditions.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.425-426
• /
• 2002

Lineal and angular movements of many engine components make the lubricant absorb air and the aerated lubricant greatly influences the clearance performance of contacting behaviors of engine components such as big-end bearing, cam and tappet, etc. This study investigates the behaviors of aerated lubricant in the gap between con-rod bearing and proceeding which is one of the most frictional energy consuming components in the engine. Our assumption for the analysis of aerated lubricant film is that the film formation is influenced by the two major factors. One is the density characteristics of the lubricant due to the volume change of lubricant by absorbing the bubbles and the other is the viscosity characteristics of the lubricant due to the surface tension of the bubble in the lubricant. In our investigation, it is found that these two major factors surprisingly increase the load capacity in certain ranges of bubble sizes and densities. Frictional forces are also influenced by the aerated bubble size and density, which eventually enlarge the shear resistance due the surface tension, Modified Reynolds' equation is developed for the computation of fluid film pressure with the effects of aeration ratio under the dynamic loading condition. From the calculated load capacity by solving modified Reynolds' equation, proceeding locus is computed with Mobility method at each time step.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.3
• /
• pp.79-89
• /
• 1995

Rattle noise occurs at manual transmission as idling and driving of a automotive. It can be solved by torsional characteristics of a clutch disc. A clutch disc consist of a region of pre-damper and main-damper. Rattle noise is affected by pre-damper and main-damper equipped for a torsional spring and friction washer. Pre-damper range covers noise radiating from manual transmission when engine is idling and main-damper range covers noise when engine is driving. The aim of this reserch is to clear transmission rattle noise by way of torsional characteristics of a clutch disc. The experiment is carried out as idling and driving of a automobile equipped for 1.5L MPI engine, dry single-disc type clutch and manual transmission. In this study, the results show for a vibration of manual transmission as idling and driving can be cleared by a clutch disc of Pre-damper type.

• Tribology and Lubricants
• /
• v.30 no.1
• /
• pp.21-28
• /
• 2014

Damage to the cylinder liner of large ship engines, such as scuffing on the surface, can occur very easily because it is operated in a corrosive environment. This scuffing may be due to oil film destruction and corrosive wear caused by water and sulfur included in the fuel, abrasive impurities, and poor lubricants. Thus, a method for monitoring the condition and diagnosing the failure of the cylinder liner and piston ring is needed. In this study, a reciprocating friction and wear test was carried out with a cast iron specimen, which simulated an engine cylinder in a corrosive atmosphere. The lubricants used were base oil, stirred oil with distilled water, a NaCl solution, and dilute sulfuric acid. The friction coefficient and frequency spectrum were measured using a load cell and acceleration sense in each experimental condition. We then used these results to diagnose the failure of the cylinder liner.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.4
• /
• pp.697-702
• /
• 2007

The lubricational characteristics about friction and wear has an important effect on the material quality of surface. Therefore, in the case of automobile engine oil which is used under severe running condition, or therefore, the seizure and anti-scuffing is very important. We have studied the lubricational characteristics of auto engine oil with additives using Falex wear test machine. We have obtained the studied result is as fellows. In order to more improved the surface roughness characteristics adding the P(phosphate) as additives is excellent at a low temperature. Adding the ZnDTP and Ca-phenate is excellent on the anti-wear and extreme pressure properties at the high load. Moreover, when the ZnDTP and P are added, the temperature properties is excellent because the stability is maintained in a high temperature.

• Tribology and Lubricants
• /
• v.26 no.5
• /
• pp.291-296
• /
• 2010

The purpose of this paper is to study the fuel economy improvement experimentally when the viscosity of engine oil is lowered. The emissions are measured for CVS-75 mode with SAE viscosity grades. The test results indicate that a close correlation has been found between the engine oil viscosity and the fuel economy. The lowering of engine oil viscosity causes the reduction of friction loss which has a very close relation with the fuel economy. These results as the lowering of engine oil viscosity will be a important factor for improvement of the fuel economy and reduction of the $CO_2$ emission.