• 한국자동차공학회논문집
• /
• 제12권4호
• /
• pp.34-34
• /
• 2004

The purpose of this paper is analyzing the oil film pressure distribution and the minimum oil film thickness for a connecting rod bearing using an A VL′s EXCITE program. It is very important to understand optimized oil supplying holes and oil groove dimensions for supporting sufficiently inertia forces and gas pressures from the combustion chamber for a Diesel engine. The computed results indicate that the optimized oil groove width of a bearing and oil hole of a journal are recommended for high performance of a connecting rod bearing at the elastohydrodynamic lubrication zone. These results as design parameters are very useful data for a bearing designer as a firm reference of an automotive engine.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1993년도 춘계학술대회 및 공장견학
• /
• pp.39-53
• /
• 1993

The minimum oil film thickness(MOFT) in the connecting-rod bering of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film charactrtistics. And cylinder pressure, crank-pin surface temperature and bearing tenp ture are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable detmuuination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• Tribology and Lubricants
• /
• 제10권1호
• /
• pp.14-26
• /
• 1994

The minimum oil film thickness(MOFT) in the connecting-rod bearing of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film characteristics. And cylinder pressure, crank-pin surface temperature and bearing temperature are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable determination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• Tribology and Lubricants
• /
• 제33권1호
• /
• pp.23-30
• /
• 2017

The electric controlled marine diesel engine has fuel pump generating the high pressurized fuel for fuel injection to combustion chamber via a common rail. Fuel pump consists of a cam-roller system. Journal bearing installed between a roller and a cam-roller pin is subjected to fluctuating heavy and instant loads by cam lift. First, Kinematic analysis is carried out to predict bearing loads during one cycle acting on the journal bearing. Second, flexible multi-body dynamic analysis and transient elasto-hydrodynamic(EHD) lubrication analysis for journal bearing considering elastic deformation of cam-roller pin, roller and bearing are conducted using AVL EXCITE/PU software to predict lubrication performance. The clearance ratio and journal groove shape providing lubrication oil are important parameter in bearing design having good performance and can be changed easier than other design parameters such as diameter, width, oil supply pressure and bearing material grade. Generally, journal bearing performance is represented by the minimum oil film thickness(MOFT) and peak oil film pressure(POFP). As well as the traditional design parameters(MOFT, POFP), in this study, temperature rise of lubrication oil is also evaluated through the side leakage flow of supplied oil. By the evaluating MOFT, POFP and temperature rise, the optimum bearing clearance ratio is decided.

• International Journal of Automotive Technology
• /
• 제7권3호
• /
• pp.245-249
• /
• 2006

Accelerated aging of engine exhaust system components such as catalytic converters are traditionally performed using an engine/dynamometer test stand. $SwRI^{(R)}'s\;FOCAS^{(R)}$ system reduces or eliminates many of the engine based aging limitations. This paper will describe several studies. These include: 1) replication of engine based catalyst aging cycles with added precision and dependability; 2) catalyst aging with and without lubricating oil effects; 3) effects of lubricant phosphorus on catalyst performance; and 4) the potential to thermally age components beyond the capabilities of engine based systems. The first study includes the development of the SwRI FOCAS system to run programmed aging conditions with or without lubricating oil. A description of the subsystems is given. The second two studies used the SwRI FOCAS system to age catalysts. One study compared thermal-only aging using of the SwRI FOCAS system with equivalent aging on a traditional engine/dynamometer test stand. The other study examined the effect on catalyst performance of two lubricating oils containing different levels of phosphorus, and compared the results to field data generated using the same oils in a fleet of vehicles.

• 센서학회지
• /
• 제21권6호
• /
• pp.434-439
• /
• 2012

In this study, the oil degradation measuring for integrated sensor of drain valve was fabricated. A sensor used in the experiments was integrated with drain valves and installed in oil pan without requiring additional space. As a result of the experiments, the capacitances changed with two inflection points in accordance with an after in mileage. The first inflection point indicated the exhaustion of oil additives, and after the second inflection point, the oil degradation was completed, which increased the viscosity and disabled the functions of oil. Thus, this section was determined as the time of oil exchange.

• 한국자동차공학회논문집
• /
• 제6권1호
• /
• pp.122-133
• /
• 1998

This paper presents the static analysis, the modal analysis and the forced vibration analysis on engine structures to find out the structure-borne noise sources by finite element method. The deformation of engine structures under the maximum combu- stion gas force was calculated through the static analysis, and the resonance possibilities were predicted by the modal analysis which ascertains mode shapes and the corresponding frequencies of engine global and its major noise sources in engine surfaces were investigated with the forced vibration analysis by means of finding the transfer mobilities on engine surfaces due to the piston impact and the velocity levels due to the combustion in consideration of oil film stiffness and damping coefficients. Finally, the direction of engine structure-borne noise reduction can be estabilished by the above-mentioned analysis procedure and the reduction effect of cost on proto-type engine build-up is expected.

• Tribology and Lubricants
• /
• 제13권2호
• /
• pp.82-88
• /
• 1997

This paper describes an empirical equation which can be used to predict the engine condition of supersonic aircraft. The equation, which is derived from the trend analysis of JOAP data, represents the concentration of Fe particles in the engine oil. The result of the trend analysis shows that the concentration of Fe particles is a function of running time of engine oil. Meanwhile the slope of Fe concentration is a function of running time of engine. Threfore, the empirical equation was derived as $w=a(t_e).t_o+b$. However, the equation could not enough to diagnose the damaged part of engine quantitatively. To make up for the weak points of the equation, qualitative analysis was carried out. For that purpose wear debris were collected from the abnormal engine and analyzed by EDS to detect the damaged parts of engine.

• 한국자동차공학회논문집
• /
• 제16권5호
• /
• pp.22-28
• /
• 2008

A closed type crankcase ventilation system has been adopted to engines to prevent emission of blow-by gas to atmosphere. In the early closed type crankcase ventilation system, blow-by gas which contains engine lubricating oil is re-circulated into the intake system. The blow-by gas containing oil mist leads to increased harmful emissions and engine problems. To reduce loss of the engine oil, a highly-efficient oil separation device is required. Principle of a cyclone oil separator is to utilize centrifugal force in the separator and, therefore, oil separator designs depend on rotational flow which causes the centrifugal force. In this paper, flow characteristics and oil separation performances for cyclone type designs are calculated with CFD methodology. In the CFD model, oil particle was injected on a inlet surface with Rosin-Rammler distribution and uniform distribution. The major design parameters considered in the analysis model are inlet area, cone length and outlet depth of the oil separator. As results, reducing inlet area and increasing cone length increase oil separation performance. Changes in outlet depth could avoid interference between rotational flow and outlet flow in the cyclone oil separator.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1121-1126
• /
• 2003

Strength evaluation was carried out for the fillet and oil hole of crankshaft of medium speed diesel HiMSEN engine to verify initial concept design. Alternating torque obtained from torsional vibration analysis and radial force due to firing pressure were applied. It was assumed that the maximum alternating torque and radial force occur simultaneously. Weak points in view of fatigue are proceeding fillet and crank pin fillet area and the minimum normalized fatigue safety factor is 1.17 at crank pin fillet. The fatigue strength of the oil hole was evaluated to verify the effect of the surface roughness of the oil hole. As results, the specific level of the inner surface roughness and the polishing depth of the oil hole for sufficient fatigue strength was suggested. The maximum stress value and stress distribution at the inner surface of the oil hole can be easily estimated at initial design stage by the newly developed method.