• Proceedings of the Acoustical Society of Korea Conference
• /
• 1994.06a
• /
• pp.662-667
• /
• 1994

This paper presents the design and construction details of a soundproof enclosure for housing 20 KVA diesel generator-set. As the generator had to be installed close to the hospital building, it was desirable to reduce the transmission of noise by housing the generator in such an enclosure. The diesel engine being an air cooled one, it was essential to supply fresh air into the enclosure for its cooling. Forced inflow of air is provided through an inlet duct located in such a way that the incoming fresh air is thrown close to the inlet of cooling fan of the engine. The high velocity air stream, which heats up while passing over the engine head, escapes to the atmosphere through a rectangular outlet duct with enlarges inlet that receives hot air from the engine. The air ducts were designed specially and have been provided with acoustic lining for sound absorption. The masonary enclosure has been provided with double glazed fixed windows and double doors. The exhaust pipe of the engine fitted with a muffler has been taken out through the enclosure wall facing away from the hospital. Acoustic performance studies conducted in terms of attenuation provided by the enclosure at different frequencies have also been presented and discussed. The noise control measures adopted for building the sound-proof enclosure have been found to be quite effective as the noise levels inside the hospital building are now within the acceptable limits.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.5
• /
• pp.545-557
• /
• 2021

Engine is the main source of vibration that generates unwanted noise and vibration of vehicle chassis. Especially, in submarine applications, radiation of noise signatures can be detected at some distance away from the submarine using a sonar array. Thus quiet operation is crucial for submarine's survivability. This study addresses reduction of the force transmissibility originating from engines and transmitted to hull through engine mounts. An inertial damper, as an actuator of hybrid mount system, is addressed to reduce even further the level of vibration. Narrow band FxLMS algorithms are broadly used to cancel the vibration of engine mount because of its excellent performance of canceling narrow band noise. However, in real active dampers, the maximum displacement of damper mass is kinematically restricted. When the control input signal from the FxLMS algorithm exceeds this limitation, the damper mass will collide with the mechanical stops and results in many problems. Originated from these, a modified narrow band FxLMS algorithm based on the equalizer technique with the maximum allowable displacement of active damper mass is proposed in this study. Some simulation results showed that the propose algorithm is effective to suppress vibration of engine mount while ensuring given displacement constraint.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.883-884
• /
• 2012

This study deals with design and application of silencer to reduce the exhaust noise, especially at the low frequency range below 200 Hz which is main contribution for the bridge wing noise and the external noise of ships. The designed silencer is composed of side branch resonator, Helmholtz resonator and absorbing material. The resonating frequencies of resonators are set to be the firing order frequencies of the generator engine. Based on the on-board measurement result, it is verified that the designed silencer can effectively reduce the exhaust noise of generator engine.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.39 no.2
• /
• pp.134-142
• /
• 2003

Most of the vibration and noise generating in small boats come from shipboard machinery such as main engine, generator and auxiliary machinery etc. In order to build up the comfortable environment for the crew and to reduce the ambient noise, and provide basic materials for reasoning selection application, the design under allowable vibration & noise conditions and the examination of vibration condition of the new ships, this paper researches the frequency spectrum and order analysis of vibration and noise. The obtained results are summarized as follows : Through comparing the small boat internal noise with the regulation of IMO and DNV, it revealed that the noise level of main engine room accords with the standard, and the noise of other places are beyond the values. In this paper, two boats are analyzed, which are same type, same size and power, but the main engines noise of them is different. In order to search the noise source, the noise of main engine room and relative parts are measured. The third order of measured points is dominant in frequency domain by the order analysis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.880-885
• /
• 2007

Diesel engines have been widely used in ships and power plants because of its higher thermal efficiency, mobility and durability compared to other prime movers. Though these merits, diesel engine including main components are sometimes vibrated due to higher combustion pressure in cylinders. Especially torsional, axial and structural vibrations in propulsion shafting may be severely manifested by the malfunction of torsional and axial dampers and misfiring and unbalanced load in cylinder. The structural vibration of main body and turbocharger core hole are also occurred by the loosen top bracing and excess wear-out or failure of turbocharger's bearings. The marine diesel engine should be safely designed from these vibrations. This paper introduces experimental methods to develop the prototype of integrated vibration monitoring system for marine diesel engine.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.1
• /
• pp.46-52
• /
• 2012

Since the engine and reduction gear in a naval vessel are usually supported by the mounting system separately, the misalignment between the input shaft of the reduction gear and the output shaft of the engine should occur caused by ship motion. In this study, this misalignment is estimated from the linear static analysis assuming that the phase of movements of the engine and reduction gear at low frequency range is same and the dynamic effect is not affect to them. Through comparing the relative displacement of the engine and reduction gear calculated from linear static analysis to that from dynamic analysis as well as experiment, the assumption in this study could be verified.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.1112-1118
• /
• 2007

This paper investigates the performance of an electromagnetic type active control engine mount (ACM) recently developed in the laboratory. The ACM employs the basic structure of the conventional hydraulic engine mount of which upper chamber is connected to a dual magnet electromagnetic actuator. The actuator, that essentially replaces the existing decoupler of the conventional passive hydraulic engine mount, actively controls the upper chamber pressure. Using the linearized ACM model incorporated with the actuator dynamics, we suggest an optimal design of ACM, maximizing the actuator efficiency as well as the vibration isolation efficiency.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.1106-1111
• /
• 2007

This paper is focused on design of a new active control engine mount (ACM), which is compact in size and cost effective. The ACM, consisting of an electrodynamic actuator as the active element, flat springs and a sliding ball joint, is different in structure from the previous ACM designs based on the conventional hydraulic engine mount. Dynamic characteristics of the proposed ACM are extensively investigated before a prototype ACM, which meets the design specifications, is built in the laboratory. For cost effectiveness, a feed-forward control algorithm without a feedback sensor is used for reduction of the transmitted force through the ACM from the engine. The prototype ACM is then harmonic-tested with a rubber testing machine for verification of its control performance as well as adequacy of modeling. Experimental results show that the proposed ACM is capable of reducing the transmitted force by 20 dB up to the frequency range of 60 Hz.

• Journal of KSNVE
• /
• v.8 no.1
• /
• pp.122-131
• /
• 1998

Internal and external acoustic fields of the engine inlet are calculated by using a finite element method. The far fields non reflecting boundary condition is enforced by using a wave envelope element, which is a kind of infinite element. The geometry is assumed an axisymetric duct. Sources of the fan are modeled by the Tyler and Sofrin's theory. Effects of uniformly moving medium are considered. A pulsating sphere and an oscillating piston problem are calculated to verify the external problems, and compared with exact solutions. When the wave envelope element is applied at the far boundary, the calculated finite element solutions show good agreements with the exact solutions. The engine inlet is solved with the combined internal and external grid. The cut-off phenomena on engine inlet duct are observed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.7 s.100
• /
• pp.865-870
• /
• 2005

Torque fluctuation of the engine and angular velocity variation of propeller shaft is the main excitation source for torsional vibration in the vehicle driveline. Experimental model for engine system is constructed with 4 cylinder 4 cycle diesel engine including Motor-Propeller Shaft-Axle-Wheel system. The angular velocity is measured by magnetic pickup and FV converter at the engine flywheel and propeller shaft. This paper presents the theoretical mechanism of these excitation sources and it is identified by the experimental methods.