• Journal of Advanced Marine Engineering and Technology
• /
• v.13 no.3
• /
• pp.64-71
• /
• 1989

In this paper, a computer program for simulation of 4 cycle diesel engines including intake and exhaust manifold system is developed. The wave action theory is applied for optimization of the intake and exhaust manifold system. The calculation results of this computer program is finely accurate and agreed well with experimental results. Accordingly, it is recognized that the developed computer program can be utillized very usefully for the design of intake and manifold system. And then, influential factors of the engine performance in the design of intake manifold is numerically investigated by the calculation only. As the results it is concluded that the inertia one of the dynamic effects on the intake and exhaust maninfold affects mainly the engine performance and the pulsation one is a side effect.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.388-391
• /
• 2012

Intake start characteristics of a Mach 5 scramjet engine were investigated experimentally. Intake unstart was observed. The model-facility interaction or excessive internal contraction ratio were attributed to this unstart. Intake start was achieved by changing the model position to remove the model-facility interaction, and by modifying the cowl to give smaller contraction ratio.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.3
• /
• pp.796-805
• /
• 1995

For the purpose of improving performances of a turbocharged diesel engine at low speed, this study investigates the effects of the injected air for the performances and flow characteristics in the intake and exhaust pipes by using the computer simulation with test bed. In the theoretical analysis, the whole flow system, including engine cylinders and intake and exhaust pipes, is calculated numerically by the method of filling and emptying. From the results of this study, the following conclusions may be summarized. Increasing injected air pressure into the pipe of compressor exit brings about the improvement in a performance and flow characteristics of intake and exhaust pipes under full load operating conditions at 1000 rpm of the engine speed, but shows trends of the inferior performances under no load operating conditions at 2000 rpm of the engine speed.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.272-275
• /
• 2008

One of the important operating factors for the air-fuel pre-mixed conditions in an HCCI engine is an in-cylinder flow. In this study, unsteady in-cylinder air flow characteristics in a diesel engine as a reference engine of an HCCI engine development were numerically analysed. Unsteady flow analyses were conducted with the combination of 3 intake port inlets, then the in-cylinder air flow distribution and swirl ratio results from a case were compared with the results from the other cases.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.833-838
• /
• 2011

Future powertrain technologies will be developed focused on applications of eco-friendly technology for internal combustion engine, electric vehicle and Fuel Cell Electric Vehicle. But it is expected that these cutting edge technologies will not be applied immediately due to lack of infrastructure, technical and economical reasons. Therefore, numerous developments of internal combustion engine will be carried out for the time being. There have been many turbo engine developments undergoing to maximize the engine performance using turbo charger system in accordance with global trend-green technology and downsizing of engine which coincides with HMC's future development strategy. This study reviews the development process and result of plastic intake manifold module which is firstly developed for turbo engine. CAE simulation and experiments were implanted to evaluate design validity.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.27-34
• /
• 1997

The effects of the intake and exhaust valve timing to improve the engine performance in a spark ignition 3-cylinder LPG engine with a closed loop fuel supply system were studied. The engine torque and power have been measured using the 75kW EC-dynamometer while adjusting the optimal fuel consumption ratio with a solen- oid driver. As the results from this experiment, when intake valve opening is $12^{\circ}$ BTDC, intake valve closing is $36^{\circ}$ ABDC, exhaust valve opening is $12^{\circ}$ ATDC, and exhaust valve closing is $36^{\circ}$ BBDC respectively, the best torque characteristics in low and high speeds for a gives engine were obtained. And also we could find that the torque characteristics in low speeds were affected by the timing of exhaust valve open. An increased valve overlap by the EVC delay was ineffectual to the torque characte- ristics improvement in high speeds.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.75-86
• /
• 1986

This paper describes a simulation program of intake and exhaust processes in a 4-stroke S.I. engine and also studies the relationship among various engine parameters under different engine speed and load conditions. This simulation program includes the engine cylinder model for the intake and exhaust processes and its formulation and evaluates the system characteristics such as inlet mass, pumping work and residual gas in the cylinder-which influence on power output, fuel economy and exhaust emissions. In order to evaluate the accuracy of the simulation program, predicted results were compared with the experimental data obtained on the 4-stroke, 4-cylinder gasoline engine and satisfactory agreement was obtained.

• Journal of Power System Engineering
• /
• v.9 no.2
• /
• pp.19-25
• /
• 2005

Empirical experiments have been undertaken to investigate the effects of Intake Pulsating Flow on volumetric efficiency in a diesel engine. Waves occurs in the manifolds of engine owing to the periodic nature of the induction and exhaust processes caused by piston motion. During induction process, as waves travel both directions, they are reflected and interacted each other and pressure waves are transmitted through it. Hence, the flow become more complex and unsteady flow. These pressure waves act upon intake pulsating flow and affects on volumetric efficiency. In this paper the effects of change in length of induction pipes and wide range of engine speed on volumetric efficiency was examined and evaluated. It was found that volumetric efficiency was affected by intake pulsating flow with engine speed and the pipe length. The results obtained were considered by adopting a theory of wave action.

• 한국연소학회:학술대회논문집
• /
• 2012.04a
• /
• pp.105-106
• /
• 2012

This study is numerical analysis about optimal conditions of GDICI (gasoline direct injection compression ignition) engine operation using intake preheating. Numerical modeling was performed by using the KIVA-3V Release2 code integrated Chemkin chemistry solver II. For validation of numerical model, experiments were performed on a single-cylinder engine. Throughout the numerical simulations under variable conditions, the ranges of optimal conditions were found.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2186-2191
• /
• 2003

This study is to investigate the effects of water induction through the air intake system on the characteristics of combustion and exhaust emissions in diesel engine. The effects of water induction through the air intake port were considered in IDI diesel engine in this study. The formation of NOx was significantly suppressed by decreasing the gas peak temperature during the initial combustion process because the water play a role as a heat sink during evaporating in the combustion chamber, but the smoke was slightly increased with increased water amount. Also, NOx significantly decreased with increase in water amount. A simultaneous reduction in smoke and NOx emissions can be obtained when water is injected into the combustion chamber by retarding the fuel injection timing more than without water injection.