• 대한기계학회논문집
• /
• 제16권3호
• /
• pp.453-458
• /
• 1992

본 연구에서는 유한요소법에 바탕을 둔 최적공정설계법을 이용하여 압출 금형 형상의 최적설계를 실시하였다.설계의 결과를 참고문헌에서 발췌한 이론해와 비교 하였으며, 축대칭 압출공정에서 압하율, 마찰, 재료특성 등이 금형의 최적형상에 미치 는 영향에 대하여 조사하였다.

• Journal of Magnetics
• /
• 제21권3호
• /
• pp.468-475
• /
• 2016

In this article, entropy generation on MHD Williamson nanofluid over a porous shrinking sheet has been analyzed. Nonlinear thermal radiation and chemical reaction effects are also taken into account with the help of energy and concentration equation. The fluid is electrically conducting by an external applied magnetic field while the induced magnetic field is assumed to be negligible due to small magnetic Reynolds number. The governing equations are first converted into the dimensionless expression with the help of similarity transformation variables. The solution of the highly nonlinear coupled ordinary differential equation has been obtained with the combination of Successive linearization method (SLM) and Chebyshev spectral collocation method. Influence of all the emerging parameters on entropy profile, temperature profile and concentration profile are plotted and discussed. Nusselt number and Sherwood number are also computed and analyzed. It is observed that entropy profile increases for all the physical parameters. Moreover, it is found that when the fluid depicts non-Newtonian (Williamson fluid) behavior then it causes reduction in the velocity of fluid, however, non-Newtonian behavior enhances the temperature and nanoparticle concentration profile.

• Korean Chemical Engineering Research
• /
• 제54권1호
• /
• pp.108-113
• /
• 2016

A miniaturized lab-scale Cu plating cell for the metallization of electronic devices was fabricated and its deposit uniformity and profile were investigated. The plating cell was composed of a polypropylene bath, an electrolyte ejection nozzle which is connected to a circulation pump. In deposit uniformity evaluation, thicker deposit was found on the bottom and sides of substrate, indicating the spatial variation of deposit thickness was governed by the tertiary current distribution which is related to $Cu^{2+}$ transport. The surface morphology of Cu deposit inside photo-resist pattern was controlled by organic additives in the electrolyte as it led to the flatter top surface compared to convex surface which was observed in the deposit grown without organic additives.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권1호
• /
• pp.16-22
• /
• 2002

The Proposed contactless charger employs a Pair of neighboring Printed circuit board (PCB) windings as a contactless energy transfer device, thereby making it amenable to low-Profile designs and suitable for applications to the portable telecommunication/computing electroncis in which stringent requirements for height, space, and reliability have to be met. The performance of the proposed charger is confirmed with experiments on a prototype charger developed for cellular phones

• KSTLE International Journal
• /
• 제6권1호
• /
• pp.21-27
• /
• 2005

A technique for a wear volume calculation is improved and verified in this research. The wear profile data measured by a surface roughness tester is used. The present technique uses a data flattening, the FFT and the windowing procedure, which is used for a general signal processing. The measured value of an average roughness of an unworn surfnce is used for the baseline of the integration for the volume calculation. The improvements from the previous technique are the procedures of the data flattening and the determination of a baseline. It is found that the flattening procedure efnciently manipulates the raw data when the levels of it are not horizontal, which enables us to calculate the volume reasonably well and readily. By comparing it with the weight loss method by using artificial dents, the present method reveals more volume by aroung 3~10%. It is attributed to the protruded region of the specimen and the inaccuracy and data averaging during the weght loss measurement. From a thorough investigation, it is concluded that the present technique can provide an accurate wear volume.

• 설비공학논문집
• /
• 제14권4호
• /
• pp.350-357
• /
• 2002

Optimal control algorithms for the full storage ice cooling system were developed by using a dynamic simulation program. Control algorithms for the storage charging mode were developed for the chiller outlet temperature setpoint control and the chiller capacity control. Control algorithms for the storage discharging mode were developed for the proper mode selection, the storage-only mode control, and the storage-priority chiller-shared mode control. Two different cases of the expected outdoor air temperature profile and the expected cooling load profile were used to analyze the effectiveness of these algorithms. Simulation results show the energy savings and the satisfactory controls of the ice storage system. Therefore, control algorithms developed for this study may effectively be used for the improved control of the ice storage cooling system.

• 전자공학회논문지A
• /
• 제33A권6호
• /
• pp.144-150
• /
• 1996

The purpose of this paper is to develop a simulation program to predict resist prifile in electron-beam lithography, where the main issue is proximity effect. The simualtion program composes of monte-carlo simulation, exposure simulation and development simulation. In nonte-carlo simulation, the absorbed energy in the resist is calculated when one electron is incident into resist, using hybrid model on the basis of the rutherford differential scattering cross section and moller theory. In exposure simulation, the absorbed energy in the resist is calculated when electrons are incident in exposure pattern. In the program, the developed profile depending on time is obtained by string model. The 0.2$\mu$m and the 0.3$\mu$m line and space patterns are experimentally delineated and compared to the simulation results to check the relevance of the program.

• 한국표면공학회지
• /
• 제29권6호
• /
• pp.654-659
• /
• 1996

Amorphous $TiO_2$ thin films were deposited on silicon substrates by the RF magnetron sputtering under various conditions, and studied by the spectroscopic ellipsometry (SE). To determine the optical constants as a function of photon energy and also to depth-profile the as-deposited $TiO_2$ thin films, we analyzed the ellipsometric spectra using the effective medium approximation and the dispersion equations. Especially, we improved the modeling accuracy by selectively using either the Sellmeier or the Forouhi and Bloomer dispersion equation in different energy regions.

• 열처리공학회지
• /
• 제19권5호
• /
• pp.262-269
• /
• 2006

The development of eco-friendly low pressure carburizing system with high pressure gas quenching(LPC-GQ, 500kg/charge) led to new stage in the fundamental case-hardening treatments. This is due to its ability to provide tighter tolerances on the carburizing process with notable reductions in distortion of the carburized and hardened workpiece. This system is characteristics by high uniformity and reproducibility of heat treatment results, absence of an intergranular oxidation layer, carburizing of complex shapes, reduced cycle time, low operating costs, simplified production, eliminate post washing, and reduced grinding costs.

• 한국초전도ㆍ저온공학회논문지
• /
• 제1권1호
• /
• pp.42-47
• /
• 1999

Enthalpy transport in a pulse tube was investigated by two-dimensional analysis of mass. momentum an energy equations of the gas as well as energy conservation of the tube wall. The mean temperature of the gas and the tube wall was obtained directly by assuming that the outer surface of a pules tibe wall is adiabatic. Axial profile of mean temperature is small. but it deviates significantly from linear profile when the dimensionless frequency is large. Effect of operating frequency. tube wall thickness, velocity ratio and velocity phase angle between both ends of a pulse tube on net enthalpy flow were shown.