• Wind and Structures
• /
• 제30권1호
• /
• pp.29-35
• /
• 2020

This paper presents a comparative structural analysis of lattice hybrid tower with six legs with conventional tubular steel tower for an onshore wind turbine using finite element method. Usually a lattice hybrid tower will have a conventional industry standard 'L' profile section for the lattice construction with four legs. In this work, the researcher attempted to identify and analyze the strength of six legged lattice hybrid tower designed with a special profile instead of four legged L profile. And to compare the structural benefits of special star profile with the conventional tubular tower. Using Ansys, a commercial FEM software, both static and dynamic structural analyses were performed. A simplified finite element model that represents the wind turbine tower was created using Shell elements. An ultimate load condition was applied to check the stress level of the tower in the static analysis. For the dynamic analysis, the frequency extraction was performed in order to obtain the natural frequencies of the tower.

• Journal of Welding and Joining
• /
• 제16권4호
• /
• pp.109-116
• /
• 1998

The three-dimensional profile of a solder fillet is predicted by minimizing the surface tension and gravity energies of the solder joint using finite element modeling. Geometric complexity stemming from the inclined plane of the gullwing lead is resolved by employing three element types. These element types are used to describe the joint profile formed on the vertical, inclined and interfacial planes. The predicted solder joint profiles show good agreements with the experimental data provided that the solder volume is adjusted considering the wicking effects. Effects of the pad length, inclined lead angle and solder volume on joint profiles are also investigated.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집 특별세미나,특별/일반세션
• /
• pp.585-592
• /
• 2009

The performance of screw compressor depends on lots of design parameters of rotor profile, such as length of seal line, wrap angle, blow hole, suction and discharge port size, number of rotor lobe, etc. The optimum rotor profile makes it possible to increase the compression efficiency with low energy consumption, and to minimize the loss of power. In this research, a new rotor profile design and performance analysis are done by computer simulation. It is expected that the volumetric efficiency is improved because the internal leakage is reduced due to the minimization of blow hole and clearance, and the stiffness of rotors is increased due to the reduction of length to diameter ratio. Also, the specific power consumption will be secured for use ranging from low to high operation speed.

• Geomechanics and Engineering
• /
• 제16권6호
• /
• pp.569-575
• /
• 2018

The stability of shallow cavities with an arbitrary profile is a difficult issue in geotechnical engineering. This paper investigates this problem on the basis of the upper bound theorem of limit analysis and the Hoek-Brown failure criterion. The influence of pore pressure is taken into consideration by regarding it as an external force acting on rock skeleton. An objective function is constructed by equating the internal energy dissipation to the external force work. Then the Lagrange variation approach is used to solve this function. The validity of the proposed method is demonstrated by comparing the analytical solutions with the published research. The relations between shallow and deep cavity are revealed as well. The detaching curve of cavity roof with elliptical profile is obtained. In order to facilitate the application of engineering practice, the numerical results are tabulated, which play an important role in tunnel design and stability analysis of roof. The influential factors on potential collapse are taken into consideration. From the results, the impact of various factors on the extent of detaching is seen intuitively.

• Journal of Nutrition and Health
• /
• 제40권2호
• /
• pp.162-171
• /
• 2007

Obesity is an independent risk factor fur coronary artery disease in the postmenopausal women, which may be mediated by alteration of blood lipid metabolism. We are aimed to evaluate the effects of low energy diet, restriction of high fat foods and exercise education on weight, fat mass and blood lipid profile. Fifteen postmenopausal obese women were studied. Subjects received detailed advice about how to achieve a reduction of weight by a low-energy diet (1,200kcal), restriction of high fat food and increased exercise in every 4 wks during 8 wk. To evaluate the effectiveness for education programs, dietary fat habit and daily nutrient intakes, exercise were tested before and after intervention. Anthropometry, computerized tomography, and blood lipid profile were assessed before and after intervention. According to the nutrition education, energy intake (from 1776.1 ${\pm}$ 28.2 kcal to 1268.7 ${\pm}$ 115.2 kcal, p < 0.001) and percent of energy from fat (21.9%, p < 0.01) were significantly decreased. However, the index of nutritional quality was over 1.0. On the contrary, exercise (from 341.3 ${\pm}$ 222.1 kcal to 569.4 ${\pm}$ 309.8 kcal, p < 0.05) was increased and dietary fat habit scores (from 30.8 ${\pm}$ 5.2 to 36.1 ${\pm}$ 3.0, p < 0.01) were improved. Also, body weight (4.2%, p < 0.001), BMI (4.5%, p < 0.001), body fat mass (3.4%, p < 0.05) and waist to hip ratio (1.1%, p < 0.05) were decreased. Among abdominal fat, visceral fat (26.1%, p < 0.05) and subcutaneous fat (14.8%, p < 0.01) were decreased. But there was no difference in visceral fat to subcutaneous fat ratio. We observed HDL-cholesterol increase (11.7%, p < 0.05), triglyceride reduction(14.8%, p < 0.05) and atherogenic index improvement (from 2.7 ${\pm}$ 0.7 to 2.3 ${\pm}$ 0.7, p < 0.05) However, there was no change in LDL-cholesterol and total cholesterol. Theses results showed that low energy diet, restriction of high fat foods and exercise education could result in reduction of body weight, fat mass, visceral and subcutaneous fat, and in improvement of blood lipid profile in the postmenopausal obese women.

• 반도체디스플레이기술학회지
• /
• 제21권4호
• /
• pp.53-58
• /
• 2022

Shape changes of hard mask play a key role in the aspect ratio dependent etch (ARDE). For etch process using high density and energy ions, deformation of hard mask shape becomes more severe, and high aspect ratio (HAR) etch profile is distorted. In this study, polygonal geometric model for shape-deformation of amorphous carbon layered hard mask is suggested to control etch profile during the process. Mask shape is modeled with polygonal geometry consisting of trapezoids and rectangles, and it provides dynamic information about angles of facets and etched width and height of remained mask shape, providing important features for real-time HAR etch profiling.

• 방사선산업학회지
• /
• 제7권2_3호
• /
• pp.115-119
• /
• 2013

The density profile measurement technology by gamma transmission has been widely used to diagnose processes in the field of refinery and petrochemical industry. This technology can reveal a clue and position of abnormal phenomenon of industrial processes during their operation. In this paper, the feasibility of the gamma transmission technology for detecting changes in the amount of fluid in a distillation column was evaluated by using Monte Carlo simulations. The simulations assumed that $^{60}Co$ (1.17, 1.33 MeV) sources and NaI (Tl) detectors (${\Phi}5{\times}5cm$) are located in opposite sides of a column and it concurrently moves in vertical direction. To determine the dependency of a spatial resolution on aperture size of a collimator, the simulation model for a tray in a column were simulated with the aperture sizes of 1 and 2 cm. The thickness of the high density area including a tray and fluid was 7.6 cm in the simulation. The spatial resolution of the tray was 8.2 and 8.5 cm, respectively. As a result, it was revealed that the conventional density profile measurement technique is not able to show the deviation of liquid level on a tray in a column.

• 대한방사선기술학회지:방사선기술과학
• /
• 제45권5호
• /
• pp.449-455
• /
• 2022

This study is to present a Geant4 code for the simulation of the absorbed dose distribution given by a medical linac for 6 MV photon beam. The dose distribution was verified by comparison with calculated beam data and beam data measured in water phantom. They were performed for percentage depth dose(PDD) and beam profile of cross-plane for two field sizes of 10 × 10 and 15 × 15 cm². Deviations of a percentage and distance were obtained. In energy spectrum, the mean energy was 1.69 MeV. Results were in agreement with PDD and beam profile of the phantom with a tolerance limit. The differences in the central beam axis data 𝜹₁ for PDD had been less than 2% and in the build up region, these differences increased up to 4.40% for 10 cm square field. The maximum differences of 𝜹₂ for beam profile were calculated with a result of 4.35% and 5.32% for 10 cm, 15 cm square fields, respectively. It can be observed that the difference was below 4% in 𝜹₃ and 𝜹₄. For two field sizes of 𝜹_50-90 and RW₅₀, the results agreed to within 2 mm. The results of the t-test showed that no statistically significant differences were found between the data for PDD of 𝜹₁, p>0.05. A significant difference on PDD was observed for field sizes of 10 × 10 cm², p=0.041. No significant differences were found in the beam profile of 𝜹₃, 𝜹₄, RW₅₀, and 𝜹_50-90. Significant differences on beam profile of 𝜹₂ were observed for field sizes of 10 × 10 cm², p=0.025 and for 15 × 15 cm², p=0.037. This work described the development and reproducibility of Geant4 code for verification of dose distribution.

• Design & Manufacturing
• /
• 제11권1호
• /
• pp.7-13
• /
• 2017

The aim of this study is to develop the dies oven for energy-saving during the pre-heated process of extrusion dies. Applying high-efficiency near-infrared heater, single cell type dies oven was developed as a substitute for traditional chest type oven. Therefore the dies is individually heated uniformly to operation temperature so rapidly. By using the developed dies oven, electric-energy consumption of preheating extrusion dies reduced up to 30% and the waiting time in the oven also minimized up to 90min. In addition, the results have shown that it is possible to accurately control the dies temperature for improving the quality of extruded profile and to minimize die bearing oxidation and nitride layer degradation responsible for surface defects on the profile and shorter die life.

• 공업화학
• /
• 제20권1호
• /
• pp.104-108
• /
• 2009

본 연구에서는 이산화탄소/수소 혼합기체가 관 모양의 Pd-Ag 막을 통과할 때 관 안에서의 이산화탄소 및 수소의 몰분율, 수소 분압, 그리고, 속도 구배 등을 CFD (Computational Fluid Dynamics) 기법을 사용하여서 다양한 유입 속도에 대해서 모사하였다. 모사 결과에 의하면 유입 속도가 증가할수록 관의 길이 방향을 따라서 이산화탄소의 몰분율이 더디게 증가함을 알 수 있었다. 또한, 혼합 기체의 유입 속도와 관의 길이가 수소 회수율에 미치는 영향에 대해서 살펴보았으며 낮은 유입속도와 긴 관의 경우에 수소 회수율이 큰 것을 알 수 있었다.