• Journal of the Korean Geotechnical Society
• /
• v.18 no.4
• /
• pp.21-32
• /
• 2002

Small and full scale model tests were performed to obtain the transient responses of shafts subjected to elastic impact by impact-echo test. Four end conditions of drilled shafts were considered: (1) free, (2) fixed, (3) rock-socketed, and (4) soft bottom. In small scale model tests, mock-up shafts were fabricated to simulate these four drilled shafts using poly-urethane and plastic material. Additionally, skin frictions between shaft and rock were changed to find out the effect of side contact on dynamic responses. All impact responses were tested in the air. Subsequently, full scale model tests were also carried out on concrete shafts that were in free and rock-socketed condition. The end conditions of the drilled shafts could be identified with good reliability by the waveforms from both small and full scale model tests. The results obtained in this study will provide an improved understanding of the impact responses for end conditions, especially for rock-socketed drilled shafts that are frequently designed and built in Korea.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.5
• /
• pp.2499-2522
• /
• 2017

Multi-hop networks are a low-setup-cost solution for enlarging an area of network coverage through multi-hop routing. Carrier sense multiple access with collision avoidance (CSMA/CA) is frequently used in multi-hop networks. Multi-hop networks face multiple problems, such as a rise in contention for the medium, and packet loss under heavy-load, saturated conditions, which consumes more bandwidth due to re-transmissions. The number of re-transmissions carried out in a multi-hop network plays a major role in the achievable quality of service (QoS). This paper presents a statistical, analytical model for the end-to-end delay of contention-based medium access control (MAC) strategies. These strategies schedule a packet before performing the back-off contention for both differentiated heterogeneous data and homogeneous data under saturation conditions. The analytical model is an application of Markov chain theory and queuing theory. The M/M/1 model is used to derive access queue waiting times, and an absorbing Markov chain is used to determine the expected number of re-transmissions in a multi-hop scenario. This is then used to calculate the expected end-to-end delay. The prediction by the proposed model is compared to the simulation results, and shows close correlation for the different test cases with different arrival rates.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.3
• /
• pp.433-442
• /
• 1989

Owing to the development of CNC machine tools and automatic programing software, the milling process with ball-end mill has become the most widely used process where three-dimensional precision machining is important. In this study, the ball-end milling process has been analyzed and a cutting force model has been developed to predict the cutting force acting on the ball-end mill on given machining conditions. The development of the model is based on the analysis of geometry of a ball-end mill an the oblique cutting process. The cutting edges of ball-end mills are considered as a series of infinitesimal elements and the geometry of the cutting edge element each cutting edge element is straight. The oblique cutting process in the small cutting edge element has been analyzed as orthogonal cutting process in the plane containing the cutting velocity vector and chip-flow vector. Hence, with the orthogonal cutting data obtained from orthogonal turning test, the cutting forces can be predicted through the model. The predicted cutting forces has shown a fairly good agreement with the test results in various plane cutting conditions.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.36 no.4
• /
• pp.123-133
• /
• 2020

The purpose of this study is to analyze the method of retrofitting flexural strength and the flexural performance of retrofitted shear walls. There are various ways to reinforce the flexural strength of reinforced concrete shear wall structural systems that have already been built, in the case of that, the external force is increased, and the internal force is insufficient. However, there are various problems, such as excessive flexural stiffness after reinforcement and increasing the thickness and length of the wall. We have developed a retrofit method to solve these problems. The wall end is excavated to place the required vertical rebars, and concrete is poured after placing rebars. This is the same concept as creating wall end boundary elements later on. We also studied the anchorage method of reinforcement and the interaction method between the retrofitting end and the existing wall. The flexural test results for the reinforced concrete shear wall using the studied retrofit method can be predicted according to the sectional analysis and FEM analysis, and there are differences in the plastic hinge length, crack propagation, stiffness degradation and energy dissipation due to the bending depending on the vertical rebar ratio of wall end.

• The Journal of Asian Finance, Economics and Business
• /
• v.8 no.1
• /
• pp.443-450
• /
• 2021

The paper investigates the factors that affect the decision of young Chinese consumers to buy high-end cosmetics. The study is based on the responses obtained by questionnaires from 400 respondents in Guangzhou, China. The information was collected and classified on the basis of gender, occupation, age and education in order to understand the main characteristics of the sample in a better way. The purposive, convenient and quota sampling techniques of non-probability sampling method were used. Besides this, the predictive test was carried out with 30 respondents to ensure the reliability and validity of the questionnaires. The data was put to descriptive statistical analysis and multiple regression analysis in order to verify the hypotheses. The data revealed that, while brand awareness does not affect the consumer attitude about the high-end cosmetics, other factors like product involvement, perceived quality, subjective norm, and word-of-mouth have significant effect on consumer's attitude and consumers' intention about high-end cosmetics. The findings of the study show that subjective norm, perceived value, word-of-mouth, and consumer attitude of cosmetic products highly affect consumers purchase intention of high-end cosmetic products. The research paper helps to form concrete and effective marketing strategy based on various aspects of consumer behavior for high-end cosmetics in China.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.603-610
• /
• 2005

The end bearing behavior of piles socketed in weathered/soft rock is generally dependent upon the mass conditions of rock with fractures rather than the strength of intact rock. However, there are few available data and little guidance in the prediction of the end bearing capacity of drilled shafts socketed in weathered/soft rock, considering rock mass weathering. Therefore, a database of 13 load tests was constructed first, and new empirical relationships between the base reaction modulus of piles in rock and rock mass properties were developed. No correlation was found between the compressive strengths of intact rock and the base reaction modulus of weathered/soft rock. The ground investigation data regarding the rock mass conditions(e.g. Em, Eur, RMR, RQD) was found to be highly correlated with the base reaction modulus, showing the coefficients of correlation greather than 0.7 in most cases. Additionally, the applicability of existing methods for the end bearing capacity of piles in rock was verified by comparison with the field test data.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.2019_2020
• /
• 2009

A recurrent surge oscillograph(RSO) test was performed at the Taean thermal power plant on #5 turbine generator. The test was conducted using a rotor reflectometer and digital oscilloscope. A DC voltage step is applied to each end of the rotor winding in turn. Each reflected wave, at the input end of the winding, is monitored and the two waveforms are superimposed automatically and monitored on a single channel oscilloscope. As the half windings in a rotor are identical, the two waveforms monitored at each end of the rotor will also be identical for a healthy winding. A winding with a fault will cause different voltages to be monitored at the two ends.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.3
• /
• pp.109-119
• /
• 2018

The purpose of this study is to evaluate the structural safety of the front-end loader for the 90 kW class of agricultural tractors in impact test conditions. Deformation and stress on the loader under the impact test conditions are analyzed using the commercial finite element analysis software ANSYS. In previous research dealing with the initial design of the loader, the maximum stress occurred in the mount and exceeded the yield strength of the material. In this paper, an improved design of the mount of the loader was proposed to reduce the stress concentration in the initial design. The safety of the improved design was verified by performing rigid-body dynamics analysis, transient structural analysis, and static structural analysis under three impact test conditions: a drop and catch test, a corner pull test, a corner push test. It was found that the local stress concentration in the mount that appeared in the initial design was greatly reduced in the improved design, and that the maximum stresses occurred in the three impact test conditions are smaller than the yield strength. It is expected that the design improvement of the mount proposed in this study and the method of analysis may be effectively used to enhance structural safety in the development of new model front loaders in the future.

• The Journal of the Korea Contents Association
• /
• v.22 no.8
• /
• pp.628-639
• /
• 2022

The purpose of this study was to investigate the relationship between the optimal end-of-life care and well-dying perceived by nurses to provide the optimal end-of-life care for patients and their families. This subjects of the study were 121 nurses working in the ward or intensive care unit of a general hospital in Seoul, and the data collected from April 28 to May 12, 2021 were analyzed. Data were analyzed using t-test, ANOVA, and Pearson correlation coefficients with the SPSS/WIN 27.0 program. The total average of the subjects' perceptions of the optimal end-of-life care was 4.04±0.82 on a five-point scale, indicating the overall level of 'agree' with the optimal end-of-life care. The total average of well dying perceived by the subjects was 3.63±1.14 on a five-point scale, and the most important recognized questions was to die peacefully. Of general characteristics, there was a significant differences on optimal end-of-life care according to age (t=-.97, p=.013). The nurse group in their 30s showed higher consent for end-of-life care than those in their 20s. An analysis of the correlation between the optimal end-of-life care and well-dying showed that there was no significant correlation. This study suggest that education should be provided to raise awareness of end-of-life care for young nurses with low experience.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.33-33
• /
• 2009

This study is to develop the resistance welding apparatus and investigate the welding characteristics of Zircaloy-4 end-plate of fuel bundle in the cases of the resistance welding and the laser beam welding. The welding parameters which affect the weld nugget and the torque values have been also compared. The effect of the torque strength of end-plate welding using by the resistance welding and the laser beam welding has been studied and optimum conditions of Zircaloy-4 end-plate welding have been found. Futhermore, micro-structures and micro-hardness of the resistance welded specimens have been also compared.