• KSTLE International Journal
• /
• 제3권1호
• /
• pp.17-22
• /
• 2002

Roughing of tool steel in its hardened state represents a real challenge in the die and meld industry and process improvement depends on research of tool material, coating technique, and lubrication. However, roughing of hardened steels generates extreme heat and without coolant flooding, tool material cannot withstand the high temperature without choosing the right tools with proper coating. This research conducted milling tests using coated ball end mills to study effects of cutting conditions and geometric parameters of ball end mills on the machinability of hardened tool steel. KP4 steel and STD 11 heat treated steels were used in the dry cutting as the workpiece and TiAIN coated ball end mills with side relief angle of 12$^{\circ}$ was utilized in the cutting tests. Cutting forces, tool wear, and surface roughness were measured in the cutting tests. Results from the experiments showed that 85 m/min of cutting speed and 0.32 mm/rev of feed rate were optimum conditions for better surface finish during rough cutting and 0.26mm/rev with the same cutting speed are optimum conditions in the finish cutting.

• 한국생산제조학회지
• /
• 제7권3호
• /
• pp.99-103
• /
• 1998

The curved surface machined by plate end mill causes a excess non-cutting volume, in these cases ball end mill is used for the curved surfaces. This study is aimed to obtain the optimum cutting conditions of various cutting speed, table speed, tool diameter, radius of curvature roughness on the conditions of various cutting speed, tool diameter, radius of curvature when machining the curved surface using the ball end mill. After designing curve rates, obtaining NC data by CAD/CAM system through CC-Cartesian method and transferred the data through DNC system, we machined the specimens by the CNC machining center, The surface roughness of specimens was measured by surface roughness tester and CNC 3D coordinate measuring machine. The cutting condition were the same as follow velocity; 15, 20, 25 30m/min, feed rate;40, 60, 80, 100m/min and radius of curvature; 30,40,50,60mm, tool diameters; ø8, ø12, ø16, ø 20mm. Analizing the working results, we can acquire the optimum cutting condition of curved specimen at the cutting velocity of 20~25m/min and the feed rate of 80mm/min. As the same cutting condition the best surface roughness was showed at ø16mm of the tool diameter. But the tool diameter was smaller than ø8mm. we could improve for the surface roughness by controlling the cusp.

• 융합신호처리학회논문지
• /
• 제5권4호
• /
• pp.281-286
• /
• 2004

FMS, FMC, FA, IMS의 구축에 있어서 최하위 단위인 공작기계의 자동화가 중요하다. 이를 위해서는 공작기계의 공구 감시기능(tool monitoring system)이 수행되어야 한다. 본 논문은 공구 감시기능의 자동화를 위해 종전의 공구마모 검출방법과는 달리 엔드밀의 마모상태에 따라 발생하는 절삭음의 음향주파수 분석을 통해 마모정도를 검출하는 방법을 제안하였다. 즉, 머시닝센터에서 공구마모가 잘되는 합금공구강재를 사용하고 이때 발생하게 되는 절삭음(cutting sound)을 음향 분석하여 공구 마모와 관련이 있는 가진 주파수(tooth passing frequency)를 찾아내고 또한 이 주파수의 크기 값과 공구마모(flank wear) 변화를 연구하여 엔드밀의 마모 상태를 추정하였다 이를 위해 본 연구에서는 실험 장비를 구성하고 절삭속도, 엔드밀마모, 공구직경을 절삭조건으로 하여 측정된 절삭음을 FFT 처리하였다. 또한 측정된 값을 회귀분석으로 모델링한 결과 엔드밀 마모 검출오차범위가 5.8% 이내로 나타나 음향주파수 분석에 의한 엔드밀 마모검출 방법의 유효성을 확인할 수 있었다.

• 대한기계학회논문집A
• /
• 제27권7호
• /
• pp.1095-1102
• /
• 2003

The most important thing in measuring the tool wear is to set up the measurement base. The end mill that is being used for machining of die is difficult to set up the base and to measure the tool wear because of geometric properties of that such as a helix and relief angle. In this study, a new instrument using spindle orientation function in end milling is developed to measure the tool wear and evaluated by the measuring system on the machine. Finally, this new method makes possible the wear measurement of same position and reduces the measuring time compared with the measuring methods such as the microscope and CCD.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.149-153
• /
• 2003

The most important thing in measuring the tool wear is to set up the measurement base. The end mill that is being used for machining is difficult to set up the base and to measure the tool wear because of geometric properties of that such as a helix and relief angle. In this study, a new instrument using spindle orientation function in end milling is developed to measure tool wear and evaluated by measuring system on the machine. Finally, this new method makes possible the wear measurement of same position and reduces measuring time compared with measuring methods such as the microscope and CCD.

• 한국기계가공학회지
• /
• 제18권11호
• /
• pp.76-82
• /
• 2019

This study aims to find the shapes of an end-mill with low cutting temperature during the end-mill process of Ti-6Al-4V alloy. Such ${\alpha}-{\beta}$ titanium alloys are increasingly more used for their high tensile strength and high corrosion resistance. The cutting characteristics of Ti-6Al-4V alloy were studied using an analytical method validated by comparing the estimated cutting resistance with that from experiments. The end-mill shape was analyzed using an experimental method. The end-mill shape with low cutting resistance and low cutting temperature was confirmed by analyzing the signal-to-noise ratios for various conditions. Then, the factors with significance factor of 95% or more were determined in the variance analysis. Finally, an end-mill shape that can ensure a low cutting temperature was proposed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.59-64
• /
• 2002

Recently the applications of high speed machining are increasing due to the need for high performance and high accuracy machining and machining for difficult-to-cut material. However, the high speed machining also accompanies some problems: the product quality can be degraded due to the tool wear and the product cast can go up due to frequent tool replacements. Therefore, it is necessary to develop a technique of quantitative tool wear measurement to determine the precise timing for tool replacement. In this respect, this study suggests a reliable technique far the reduction of error components by developing a system using a CCD camera and an exclusive jig to be able to precisely measure the size of tool wear in flat end mill for high speed machining.

• 대한기계학회논문집A
• /
• 제28권6호
• /
• pp.860-866
• /
• 2004

In the end milling operation the deflection of the cutter is an important factor affecting the accuracy of machining, with implications on the selection of cutting parameters and economics of the operation. Several studies were devoted to the end mill deflection and its effects, notably, providing a useful insight into the problem. Although the deflection affects adversely the accuracy, the flexibility of the cutter is beneficial in attenuating the overload in a sudden transient situation, as well as in attenuating chatter. The deflection of the end mill was studied both experimentally with strain gauge, tool dynamometer, laser measuring apparatus and on a finite element model of the cutting using ANSYS software. The deflection of machining tool with various helix angles was studied with FEM simulation and experiment. ANSYS analysis performed on the finite element model of the end mill provides deflection results which agree within 15.0% with the experimental ones.

• 한국기계가공학회지
• /
• 제18권6호
• /
• pp.26-32
• /
• 2019

Ball end mills used for high-speed and high-precision machining require longer machining time than flat end mills or face cutters, since the tool diameter is limited and the rigidity is reduced by the characteristics of the tool's cutting edge: at the top end of the tool, the cutting speed approaches zero and hardly removes any material. Because there is little material removal at the top end of the ball end mill, the outer cutting edge performs the majority of the work; this irregular cutting force deforms the tool and shortens its life. In this study, we attached an eddy-current sensor to a tool to measure the deformation from the cutting force and we used a tool dynamometer to measure the cutting force. We found that the change in cutting force is dependent on the change in feed rate during square-shaped processing and, as the feed rate is accelerated, the cutting force also increases. Higher cutting forces increase tool deformation.

• 대한기계학회논문집
• /
• 제17권8호
• /
• pp.2012-2022
• /
• 1993

For the machining of the sculptured surfaces on 5-axis CNC milling machine, the milling cutter direction vector was determined in the study (I) with 5-axis post-processing. Thus, it was possible to cut the sculptured surfaces on five-axis CNC milling machine with the end mill cutter. Then, for smooth machined surfaces in five-axis machining of free-from surfaces, this study develops an algorithm for prediction of cusp heights. Also, it generates tool path such that the cusp heights are constrained to a constant value or under a certain value. For prediction of the cusp height between two basis points, a common plane, containing the line crossing two basis points and the summation vector of two normal vectors at two basis points, is defined. The cusp height is the maximum value of scallops on the common plane after end mill cutter passes through the common plane. Sculptured surfaces were machined with CINCINNATI MILACRON 5-axis machining center, model 20V-80, using end mill cutter. Cusp heights were verified by 3-dimensional measuring machine with laser scanner, WEGU Messtechnik GmbH.