• 한국수소및신에너지학회논문집
• /
• 제26권2호
• /
• pp.164-169
• /
• 2015

Recent research has focused on alternative fuel to improve engine performance and to comply with emission regulation. Finding an alternative fuel and reducing environment pollution are the main goals for future internal combustion engines. The purpose of this study is to obtain low-emission and high-efficiency by hydrogen enriched CNG fuel in SI engine and is to clarify the effects of hydrogen enrichment in CNG fuelled engine on exhaust emission and performance. An experimental study was carried out to obtain fundamental data for performance and emission characteristics of hydrogen enrichment in SI engine. The experiment was conducted at 2500 rpm, bmep 2 bar, 4 bar conditions while CNG fuel was mixed with 10, 20 and 30% hydrogen blends. From the experimental results, combustion duration was shortened due to rapid flame propagation velocity of hydrogen and these were attributed to the burning velocity increasing exponentially with increasing hydrogen blending ratio. Hydrogen has much wider flammable limit than methane, gasoline and the minimum ignition energy is about an order of magnitude lower than for other combustion. By adding hydrogen, $CO_2$ and HC were reduced. However, $NO_X$ was increased dut to high rate of heat release for hydrogen substitutions.

• 대한토목학회논문집
• /
• 제34권3호
• /
• pp.999-1006
• /
• 2014

국토해양부에서 2011년 시설물별 탄소배출량 산정가이드라인을 통해 제시한 토공장비의 $CO_2$ 배출계수는 IPCC 탄소배출계수를 활용하여 연료사용량을 기반으로 만들어졌다. 하지만 이 방식은 현장의 다양한 조건을 반영하지 못한다는 단점이 있다. 따라서 이러한 단점을 보완한 새로운 배출계수가 필요하다. 본 연구에서는 토공장비를 대상으로 농도-유속측정(C-FVM)을 이용한 직접측정방식으로 $CO_2$ 배출량을 산정하고, 국토해양부에서 제시한 배출계수와 비교분석 후 토공장비의 새로운 $CO_2$ 배출계수를 제시하고자 한다.

• 천문학회보
• /
• 제40권1호
• /
• pp.42.3-43
• /
• 2015

Using a large sample of 32,000 type 2 AGNs out to z = 0.2, we present the statistical results on the ionized gas outflows, based on the analysis of the velocity shift of narrow emission lines with respect to the systemic velocity measured from the stellar absorption lines. Considering the projection effect, the fraction of type 2 AGNs with the [O III] velocity offset, which is ~50%, is comparable to that of type 1 AGNs. The velocity dispersion of [OIII] is typically larger than that of Ha, suggesting that outflow is prevalent in type 2 AGNs. A weak correlation of the OIII luminosity with velocity shift and velocity dispersion indicates that outflow velocity is stronger for higher luminosity AGNs. Based on our 3-D biconical outflow models with simple assumptions on the velocity structure, we simulate the projected 2-D velocity and velocity dispersion maps, which are spatially integrated to reproduce the measurements of SDSS AGNs. By comparing the distribution of the measured velocity and velocity dispersion of OIII, with the model grids, we constrain the intrinsic outflow velocities. The outflow velocity ranges from a few hundreds to a thousand km/s, implying a strong feedback to ISM.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2000년도 제21회 KOSCO SYMPOSIUM 논문집
• /
• pp.140-147
• /
• 2000

Using lobed burner, flame visualization and measurements of NOx and CO concentration in the combustor exit were carried out to evaluate the relation between the lobed structure in a burner and pollutant emission characteristics. The flame stability is enhanced by the lobed burner compared to conventional circular one. The correlation on fuel discharge velocity for flame blowout should be included on a variable related to the wall effect of the burner, because the flame blowout is observed at the burner having large perimeter. The burner having lobed structure in fuel discharge side compared to conventional burner reduces by 5% NOx emission due to lower flame intensity through flame elongation. Meanwhile the burner having lobed structure in air discharge side and both fuel and air discharge side increase the NOx emission.

• International Journal of Automotive Technology
• /
• 제6권6호
• /
• pp.591-598
• /
• 2005

A three-way catalyst system of a natural gas vehicle (NGV) has characteristics of higher fuel consumption and higher thermal load than a lean-bum catalyst system. To meet stringent emission standards in the future, NGV with the lean-bum engine may need a catalyst system to reduce the amounts of HC, CO and NOx emission, although natural gas system has low emission characteristics. We conducted experiments to evaluate the conversion efficiency of the NOx reduction catalyst for the lean-burn natural gas engine. The NOx reduction catalysts were prepared with the ${\gamma}-Al_{2}O_3$ washcoat including Ba based on Pt, Pd and Rh precious metal. In the experiments, effective parameters were space velocity, spike duration of the rich condition, and the temperature of flowing model gas. From the results of the experiments, we found that the temperature for maximum NOx reduction was around $450^{\circ}C$, and the space velocity for optimum NOx reduction was around $30,000\;h^{-1}$ And we developed an evaluation model of the NOx reduction catalyst to evaluate the conversion performance of each other catalysts.

• 한국연소학회지
• /
• 제21권2호
• /
• pp.22-28
• /
• 2016

High efficient and environment friendly combustion technologies are used to be operated an extreme condition, which results in unintended flame instability such as extinction and oscillation. The use of electromagnetic energy is one of methods to enhance the combustion stability and a microwave as electromagnetic wave is receiving increased attention recently because of its high performance and low-cost system. In this study, an experiment was performed with jet diffusion flames induced by microwave. Micro jet was introduced to simulate the high velocity of industrial combustor. The results show that micro jet flames had three different modes with increasing oxidizer velocity; attached yellow flame, lifted flame, and lifted partially premixed flame. As a microwave was induced to flames, the overall flame stability and blowout limit were extended with the higher microwave power. Especially the interaction between a flame and a microwave was shown clearly in the partially premixed flame, in which the lift-off height decreased and NOx emission measured in post flame region increased with increasing microwave power. It might be attributed to increase of reactivity due to the abundance of radical pool and the enhanced absorption to thermal energy.

• Geomechanics and Engineering
• /
• 제37권2호
• /
• pp.149-166
• /
• 2024

The acoustic emission (AE) technique is utilized to estimate the rock failure status in underground spaces. Understanding the AE characteristics under loading conditions is essential to ensure the reliability of AE monitoring. The AE characteristics depend on the material properties (p-wave velocity, density, UCS, and Young's modulus) and damage stages (stress ratio) of the target rock mass. In this study, two groups of granite specimens (based on the p-wave velocity regime) were prepared to explore the effect of material properties on AE characteristics. Uniaxial compressive loading tests with an AE measurement system were performed to investigate the effect of the rock properties using AE indices (count index, energy index, and amplitude index). The test results were analyzed according to three damage stages classified by the stress ratio of the specimens. Count index was determined to be the most suitable AE index for evaluating rock mass stability.

• 비파괴검사학회지
• /
• 제23권6호
• /
• pp.616-621
• /
• 2003

There are various Non-Destructive Evaluation (NDE) techniques used for measurement of residual stresses in material, such as magnetic methods, X-ray diffraction, Ultrasonic velocity measurement etc. The capabilities, applications and limitations of these techniques for evaluation of cold work/plastic deformation were studied and compared. Mild steel plates were subjected to different degree of cold deformation and were analyzed by Magneto-mechanical Acoustic Emission (MAE), Barkhausen Noise (BN) and magnetic properties (hysteresis loop parameters analysis). Further, these specimens were analyzed by X-ray diffraction and ultrasonic velocity measurements. The microhardness measurement and microstructure studies of these cold worked plates were also carried out. The results of all these studies and comparison of different techniques are discussed in this paper.

• 비파괴검사학회지
• /
• 제12권4호
• /
• pp.9-17
• /
• 1993

Three types of piezoelectric sensors to detect acoustic emission signals were developed and characterized. Epicentral displacement and velocity of a plate to have infinite boundary were calculated by convolution between a Green's function and a simulated source time function to show parabolic rising characteristic. The sensor calibration system set up was composed of a steel plate, a glass capillary, an indentor and a load cell indicator The transient elastic signals were detected by the sensors. The results were compared with the theoretical results and Fast Fourier Transformed. As the results, the sensor fabricated using a disk shape of a piezoelectric PZT element showed resonant characteristics. The sensors fabricated using a conical shape PZT element and a PVDF polymer film showed the wide band characteristics for particle displacement and velocity, respectively. The calculated results showed good agreements with the transient responses in the cases of the wide band sensors and it was confirmed that the simulated source time function had been properly assumed.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.59-64
• /
• 1997

This paper investigates the relationship between cutting conditions and Acoustic Emission(AE) signals; AEavg, AErms, AEmode, as the base working to monitor the tool wear with in-process. For this purpose, cutting tests were conducted on a CNC lathe with comprehensive cutting conditions.. It is known that AEavg and AErms are proportionaly increased as the increasing of cutting velocity and depth of cut respectively. It is also known that AEmode among three kinds of AE signals may be applied for in-process monitoring to make the self diagnosis system because of its stability to the variation of cutting condition.