• Geotechnical Engineering
• /
• v.13 no.5
• /
• pp.59-74
• /
• 1997

This paper shows the results of a series of model bests on the behavior of single steel pipe pile which is subjected to lateral load in Nak-dong river sand. The purpose of the present paper is to estimate the effect of Non -homogeneous soil, constraint condition of pile head, lateral load velocity, relative density of soil, embedded pile length, and flexural stiffness of pile on the behavior of single pile which is embedded in Nak-dong river strand. These effects can be quantined only by the results of model tests. The nonlinear responses of lateral loadieflection relationships are fitted to 2nd polynomial equations by model tests results. Also, the lateral load of a deflection, yield and ultimate lateral load max. bending moment, and yield bending moment can be expressed as exponential function in terms of relative density and deflection ratio. By comparing Brom's results with model results on the lateral ultimate load, it is found that short and long pile show the contrary results with each other. The contrary results are due to the smaller assumed soil reaction than the soil reaction of the Nakiong river sand at deep point. By comparing lateral behavior on the homogeneous soil with non-homogeneous soil, it is shown that lateral loadieflection relationship is very dependent on the upper relative density. This phenomenon is shown remarkably as the difference between upper and lower relative density increases.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.151-157
• /
• 2007

We have presented a compact two-wire helical antenna adopted an open stub in opposite to a feeding point, which is for a T-DMB antenna of mobile devices. By adjusting the length of the open stub or pasting a dielectric material on the open stub, the input impedance around 200 MHz, bands of the T-DMB, can be easily control, even though the total height of the antenna is less than 8 cm(0.053 $\lambda$ at 200 MHz). The operating mechanism of the antenna is explained by using equivalent circuits of two modes, an unbalanced mode and a balanced mode. Based on the analysis of the equivalent circuits, the effects of using the open stub are validated. Several proposed antennas have been fabricated and measured. One of the fabricated antennas has -10 dB impedance bandwidth of $196{\sim}204$ MHz(8 MHz) whose value covers one channel of the T-DMB(6 MHz). The measured $S_{21}$ of the antenna is -38.6 dB which is about 17 dB higher than that of a monopole antenna whose height is same with the proposed antenna.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.19 no.6
• /
• pp.96-106
• /
• 2020

To solve the limitation of traffic monitoring that occur from embedded sensor such as loop and piezo sensors, the thermal imaging camera was installed on the roadside. As the length of Class 1(passenger car) is getting longer, it is becoming difficult to classify from Class 3(2-axle truck) by using an embedded sensor. The collected images were labeled to generate training data. A total of 17,536 vehicle images (640x480 pixels) training data were produced. CNN (Convolutional Neural Network) was used to achieve vehicle classification based on thermal image. Based on the limited data volume and quality, a classification accuracy of 97.7% was achieved. It shows the possibility of traffic monitoring system based on AI. If more learning data is collected in the future, 12-class classification will be possible. Also, AI-based traffic monitoring will be able to classify not only 12-class, but also new various class such as eco-friendly vehicles, vehicle in violation, motorcycles, etc. Which can be used as statistical data for national policy, research, and industry.

• Journal of Intelligence and Information Systems
• /
• v.24 no.2
• /
• pp.21-35
• /
• 2018

Since the introduction of MP3 players, CD recordings have gradually been vanishing, and the music consuming environment of music users is shifting to mobile devices. The introduction of smart devices has increased the utilization of music through music playback, mass storage, and search functions that are integrated into smartphones and tablets. At the time of initial MP3 player supply, the bitrate of the compressed music contents generally was 128 Kbps. However, as increasing of the demand for high quality music, sound quality of 384 Kbps appeared. Recently, music content of FLAC (Free License Audio Codec) format using lossless compression method is becoming popular. The download service of many music sites in Korea has classified by unlimited download with technical protection and limited download without technical protection. Digital Rights Management (DRM) technology is used as a technical protection measure for unlimited download, but it can only be used with authenticated devices that have DRM installed. Even if music purchased by the user, it cannot be used by other devices. On the contrary, in the case of music that is limited in quantity but not technically protected, there is no way to enforce anyone who distributes it, and in the case of high quality music such as FLAC, the loss is greater. In this paper, the author proposes an audio watermarking technology for copyright protection of high quality stereo music. Two kinds of information, "Copyright" and "Copy_free", are generated by using the turbo code. The two watermarks are composed of 9 bytes (72 bits). If turbo code is applied for error correction, the amount of information to be inserted as 222 bits increases. The 222-bit watermark was expanded to 1024 bits to be robust against additional errors and finally used as a watermark to insert into stereo music. Turbo code is a way to recover raw data if the damaged amount is less than 15% even if part of the code is damaged due to attack of watermarked content. It can be extended to 1024 bits or it can find 222 bits from some damaged contents by increasing the probability, the watermark itself has made it more resistant to attack. The proposed algorithm uses quantization in DCT so that watermark can be detected efficiently and SNR can be improved when stereo music is converted into mono. As a result, on average SNR exceeded 40dB, resulting in sound quality improvements of over 10dB over traditional quantization methods. This is a very significant result because it means relatively 10 times improvement in sound quality. In addition, the sample length required for extracting the watermark can be extracted sufficiently if the length is shorter than 1 second, and the watermark can be completely extracted from music samples of less than one second in all of the MP3 compression having a bit rate of 128 Kbps. The conventional quantization method can extract the watermark with a length of only 1/10 compared to the case where the sampling of the 10-second length largely fails to extract the watermark. In this study, since the length of the watermark embedded into music is 72 bits, it provides sufficient capacity to embed necessary information for music. It is enough bits to identify the music distributed all over the world. 272 can identify $4*10^{21}$, so it can be used as an identifier and it can be used for copyright protection of high quality music service. The proposed algorithm can be used not only for high quality audio but also for development of watermarking algorithm in multimedia such as UHD (Ultra High Definition) TV and high-resolution image. In addition, with the development of digital devices, users are demanding high quality music in the music industry, and artificial intelligence assistant is coming along with high quality music and streaming service. The results of this study can be used to protect the rights of copyright holders in these industries.

• Korean Journal of Environmental Agriculture
• /
• v.18 no.4
• /
• pp.327-331
• /
• 1999

The purpose of this study was to find out the effects of slow-released nitrogen fertilizer (SRF) on the growth and yield of Chinese cabbage. The SRF used in this study was prepared by embedding urea into a waste paper slum. The underwater dissolution rate of SRF was very rapid during the first 12 hours and 60.4% of the embedded nitrogen was released after 72 hours. The SRF and urea was applied as nitrogen source and growth. yield, yield components, nitrogen uptake of Chinese cabbage were investigated a pot experiment. Maximum leaf length of Chinese cabbage was not different between SRF and urea treatments. Length and wish of head, number of leaf per head and fresh weight of Chinese cabbage were higher in SRF treatment than those in urea treatment, but the differences were not statistically significant. Comparing to the urea treatment, nitrogen content and nitrogen uptake efficiency of Chinese cabbage were significantly higher in SRF treatment. After the experiment, total soil nitrogen contents were not different between the SRF and urea treatments.

• Journal of the Korea Concrete Institute
• /
• v.28 no.5
• /
• pp.611-620
• /
• 2016

In the construction of nuclear power plants, only 420 MPa reinforcing bars are allowed and, therefore, so many large-diameter bars are placed, which results in steel congestion. Consequently, re-bar works are difficult and the quality of RC structures may be deteriorated. To solve the steel congestion, 550 MPa bars are necessary. Among many items for verifying structural performance of reinforced concrete with 550 MPa bars, the 43 mm hooked bars are examined in this study. All specimens failed by side-face blowout and the side cover explosively spalled at maximum loads. The bar force was initially transferred to the concrete primarily by bond along a straight portion. At the one third of maximum load, the bond reached a peak capacity and began to decline, while the hook bearing component rose rapidly. At failure, most load was resisted by the hook bearing. For confined specimens with hoops, the average value of test-to-prediction ratios by KCI code is 1.45. The modification factor of confining reinforcement which was not allowed for larger than 35 mm bars can be applied to 43 mm hooked bars. For specimens with 70 MPa concrete, the average value of test-to-prediction ratios by KCI code is 1.0 which is less than the values of the other specimens. The effects of concrete compressive strength should be reduced. An equation to predict anchorage capacity of hooked bars was developed from regression analysis including the effects of compressive strength of concrete, embedment length, side cover thickness, and transverse reinforcement index.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.3
• /
• pp.298-304
• /
• 2017

The corrosion of reinforcements embedded in concrete causes some durability problems in reinforced and prestressed concrete structures. The epoxy coated reinforcements are one of the effective and reliable methods to prevent corrosion of reinforcements. However, it has been known that the epoxy coating reduces the bond capacity of reinforcement to concrete. This paper investigates the bond behaviors of epoxy coated reinforcements experimentally using direct pull-out test. Bond behaviors of epoxy coated bars for various reinforcement diameters of 10, 19 and 29mm and thicknesses of cover concrete of 1, 2, 3, and $4.5c/d_b$ (ratio of cover to bar diameter) are examined. Total 66 specimens were manufactured and tested according to the RILEM standard method. As the diameters of the epoxy coated reinforcements increase, the difference of bond strength between epoxy coated reinforcements and uncoated bars also increases. Epoxy coated bars showed more than 85% bond performance compared to those of uncoated bars. A new formular for estimating basic development length of epoxy coated reinforcement based on equilibrium equation is proposed using this experimental result.

• Journal of Advanced Navigation Technology
• /
• v.17 no.1
• /
• pp.69-79
• /
• 2013

In this paper, DCT(Discrete Cosine Transform) and CAVLC(Context Adaptive Variable Length Coding) are co-designed as hardware IP with software operation of the other modules in H.264/AVC codec. In order to increase the operation speed, a new method using SHIFT table is proposed. As a result, enhancement of about 16(%) in the operation speed is obtained. Designed Hardware IPs are downloaded into Virtex-4 FX60 FPGA in the ML-410 development board and H.264/AVC encoding is performed with Microblaze CPU implemented in FPGA. Software modules are developed from JM13.2 to make C code. In order to verify the designed Hardware IPs, Modelsim program is used for functional simulation. As a result that all Hardware IPs and software modules are downloaded into the FPGA, improvement of processing speed about multiples of 16 in case of DCT hardware IP and multiples of 10 in case of CAVLC compared with software-only processing. Although this paper deals with co-design of H/W and S/W for H.264, it can be utilized for the other embedded system design.

• Applied Microscopy
• /
• v.12 no.2
• /
• pp.55-68
• /
• 1982

The study on the nerve cells in the pars intercerebralis(IP) of 5-day-old cabbage butterfly Pieris rapae L. was performed to observe their ultrastructures and classify them on the basis. of the differences in size, shape and relative distribution cf cell organelles. The brain-subesophageal ganglion complex was fixed in 1% paraformaldehyde-1% gluaraldehyde mixture and embedded in araldite mixture. The transverse thin sections of IP were stained with uranyl acetate and lead citrate and examined by Hitachi 500 and ]EM 100B electron microscope. Five distinct types. of nerve cells are recognized and are arbitrarily designated as Type I, Type II Type III, Type IV and Type V. Type I neurone: These neurones are neurosecretory cells. Several neurosecretory cells are. recognized in the pars intercerebralis. They are roughly round or peach-shaped cells measuring $13{\sim}25{\mu}m$ in diameter. The rounded nucleus shows about $5{\sim}10{\mu}m$ in diameter. The chromatin is predominantly diffused with only occasional dense patches. The perikaryon contains numerous. mitochondria, free polyribosomes and neurosecretory granules. The neurosecretory granules are relatively uniform in electron density, and each one is about $100{\sim}400{\mu}m$ in diameter and surrounded by a single membrane. The granules are also observed mostly as in groups. In one group of neurones the cisternae of endoplasmic reticulum are distended or in other group of neurones are not distended. Golgi saccules are slightly dilated at their lateral extremities and contains. frequenty dense rounded materials. Type II neurone: Thes have the largest soma in the pars intercerebralis about $30{\sim}35{\mu}m$ in diameter. They also show roughly polygonal in shape. The nucleus is elongated or sickle-shaped. The chromatin is mainly in the euchromatin form. The perikarya in these cells are well populated with populated with free ribosomes and contain numerous mitochondria and Golgi bodies. The cisternae of granular endoplasmic reticulum are also well distributed. Type III neurone: They are oval or spindle-shaped and also medium-sized. neurones approximately $15{\sim}17{\mu}m$ in length. The nucleus is oval or slightly elongated in shape and $8{\sim}9{\mu}m$ in length. The chromatin occurs in diffused form. The cytoplasm contains many filamentous or oval mitochondria. The perikaryon has also numerous free polyribosomes and cisternae of granular endoplasmic reticulum. Type VI neurone: They are roughly polygonal in shape probably due to the close approximation of the adjacent cells. The soma is about $7{\sim}8{\mu}m$ in diameter. The nucleus is round or oval in shape and $5.0{\sim}5.8{\mu}m$ in diameter. The necleus also occupies a large proprion of the cell body. The perikaryon is well populated with free ribosomes and contains several mitochondria and cistenae of granular endoplasmic reticulum. Type V neurone: These neurones are similar to Type VI neurones in various respects such as cell size and cell inclusion, but they differ from Type IV neurones in shape. The soma is oval or slightly elongated. The cell body contains several filamentous and oval mitochondria.

• Journal of the Korea Concrete Institute
• /
• v.20 no.2
• /
• pp.231-237
• /
• 2008

This study was performed to evaluate joint behavior of prestressed concrete(PSC)-steel mixed girders through the flexural test of 14 beams according to embedded length, amount of reinforcing steel, stud arrangement, and prestressing force. All test beams were failed by turns of desertion of reinforcing steel, stud, and steel plate. From test results, prestressing force was more effective on performance of connection than stud arrangement and reinforcing steel. And the spacing of stud is also more effective than embedding length. This paper also presented 3D nonlinear analysis considering the slip of composite section as well as the static load tests of PSC-steel mixed girders. According to the slip modulus, the nonlinear analysis showed that the behavior of hybrid girders could be divided into three parts as full-composite, partial-composite and non-composite. However, the experimental results showed that the PSC-steel hybrid girders with shear connectors took the part of partial composite action in ultimate load stage. In addition, it was founded that stud shear connectors and welded reinforcements were contributed to improve the ultimate strength of hybrid girders for about 20%.