• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.6
• /
• pp.113-121
• /
• 2014

At the end of the 19th century, a battle known as the War of the Currents was fought over how electricity would be generated, delivered, and utilized. In this day and age, there has been a growing interest in Green Growth policies as countermeasures against global warming. As a result of these policies, the use of new and renewable energy needed a power converter to replace fossil fuels has expanded. To reduce power consumption through high efficiency of conversion, Low Voltage DC (LVDC) distribution systems are suggested as an alternative. In a DC distribution system, DC loads are very efficient due to decrease the stages of power conversion. If the LVDC distribution system is adopted, not only DC load but also existing AC loads should be connected with LVDC system. Thus, the modeling of two loads is needed to analyze the DC distribution system. This paper, especially, is focused on the modeling of resistive load and electronic load including power electronic converters using ElectroMagnetic Transient Program (EMTP) software.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.28 no.1
• /
• pp.22-29
• /
• 2023

A grid-connected inverter can be used in grid-connected or stand-alone modes. Generally, a grid-connected inverter operates in a grid-connected mode, but the inverter operates in stand-alone mode if grid faults occur. In the stand-alone mode, the grid-connected inverter must supply electric power to a critical load that needs to receive stable power even though grid faults occur. Generally, three-phase loads are used as critical loads, but a single phase is configured in some cases. In these conditions, the critical load is required to unbalance the load power consumption, which makes the three-phase load voltage unbalancd. This unbalanced voltage problem can cause fatal problems to the three-phase critical loads, and thus must be addressed. Hence, this paper proposes an algorithm to solve this unbalanced voltage problem by the individual phase current control. The proposed method is verified using Psim simulation and experiments.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.6
• /
• pp.25-30
• /
• 2009

In this paper, a full-digital capacitive sensor for touch key applications is proposed. The proposed circuit consists of two capacitive loads to measure and a resistor between the capacitive loads. As the method measures the delays of the resistor and two capacitive loads respectively, and obtains difference between the capacitive loads by subtracting the two delays, it can reduce the effects of changing of operating environment variables such as supplying voltage, temperature and humidity. Experimental results show the method has l.02pF resolution and can be applied to touch key applications.

• Journal of IKEEE
• /
• v.6 no.1 s.10
• /
• pp.87-93
• /
• 2002

In this paper, an advanced load balancing algorithm in nth order Hypercube distributed system has been proposed. The new algorithm uses centralized load-balancing to avoid blocking phenomenon and processor thrashing, and shows the results which makes loads to approach average value of loads. The new algorithm is compared with several other algorithm and it shows a merit in cost function value.

• Proceedings of the KIEE Conference
• /
• 2007.10a
• /
• pp.187-188
• /
• 2007

This paper describes a simple and high-performance LDO regulator designed using a $0.18{\mu}m$ CMOS process. It is designed to provide a regulated voltage for on-chip small loads instead of for off-chip heavy loads. Since the load capacitance is very small in this applications, the frequency compensation can be easily achieved without a buffer. The designed LDO drives a load current up to 15mA and dissipates only 12uA quiescent current. The line regulation is and the load regulation is for a 9mA load step. The PSRR at 10kHz is 54dB.

• Journal of Power Electronics
• /
• v.10 no.4
• /
• pp.444-449
• /
• 2010

The generation of electric power using self excited induction generation (SEIG) is a viable option in remote and rural areas where grid electricity is not available. The generated voltage and frequency of these machines, however, varies with varying loads. This characteristic can be resolved either by adjusting the values of the excitation capacitance or by controlling the prime mover speed. Further, in a single-point constant power application, where the machines deliver a fixed amount of power, the electronic load controller (ELC) can be used to switch-in or switch-out a dump load whenever the consumer load decreases or increases respectively. This paper presents a detailed analysis and the design of a microcontroller based SEIG -ELC system intended for stand-alone pico hydro power generation. The simulated performance of the controller is supplemented by experimental results.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.4
• /
• pp.404-409
• /
• 2009

A DC power system has many loads with various functions. In particular, these sizable loads take the form of power electronic converters. When they are tightly regulated, the loads appear as constant power loads and result in negative incremental input impedance. Under certain conditions the effect of such loads on the power system is causes instability. In this paper, converter with a large storage capacitor and a lag compensator is proposed as a DC bus conditioner to mitigate the voltage transients on the bus. In addition, the proposed control approach has the advantage of performing both the functions of mitigating the voltage bus transients and maintaining the level of energy stored. Simulation and experimental results showed that the proposed control method was operated well in a small-scale DC power system that contained subsystems with constant power characteristics, such as DC/DC converters and electrical drives.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.1
• /
• pp.29-34
• /
• 2012

Due to the increasing of nonlinear loads such as converters and inverters connected to the electric power distribution system, and extensive application of harmonic generation sources with power electronic devices, disturbance of the electric power system and its influences on industries have been continuously increasing. Thus, it is difficult to construct accurate load model for active and reactive power in environments with harmonics. In this research, we develop a load modeling method based on Extreme Learning Machine(ELM) with fast learning procedure for residential loads. Using data sets acquired from various residential loads, the proposed method has been intensively tested. As the experimental results, we confirm that the proposed method makes it possible to effective estimate active and reactive powers than conventional methods.

• Proceedings of the KIEE Conference
• /
• 2006.07a
• /
• pp.220-221
• /
• 2006

This paper presents a single-phase parallel active power filter with an analog control circuit to eliminate for harmonic source currents generated by nonlinear loads. The proposed system removes the harmonic source currents by injecting a compensation current that is 180' out of phase with the load harmonic current. The detection of the load harmonics is realized by a simple new structure, referred to the Notch Filter with GIC (Generalized Impedance Converter), which has higher Q than existing harmonic detecters and a simpler structure. The compensation current is obtained using the proposed harmonic detection circuit, DC-Link voltage, and output current of the full-bridge inverter controlled current mode PWM controller. The operation of the proposed system is verified experimentally.

• Structural Engineering and Mechanics
• /
• v.55 no.3
• /
• pp.525-534
• /
• 2015

A new structural dynamic fuzzy reliability analysis under stochastic loads which are applied several times is proposed in this paper. The fuzzy reliability prediction models based on time responses with and without strength degeneration are established using the stress-strength interference theory. The random loads are applied several times and fuzzy structural strength is analyzed. The efficiency of the proposed method is demonstrated numerically through an example. The results have shown that the proposed method is practicable, feasible and gives a reasonably accurate prediction. The analysis shows that the probabilistic reliability is a special case of fuzzy reliability and fuzzy reliability of structural strength without degeneration is also a special case of fuzzy reliability with structural strength degeneration.