• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.11
• /
• pp.226-233
• /
• 2013

In this study, In Laver's automatic drying device, laver thickness measurement and control devices that are associated with. Disconnect the water and steam, after put a certain amount of the mixture(water and laver) in the mold. In process, Laver of the size and thickness (weight) to determine, constant light source to detect and image LED Lamp occur Vision Sensor (Camera) prepare, then the values of these state of the image is transmitted in real time embedded computers. Built-in measurement and control with the purpose of the application of each of the channels separately provided measurements are displayed on a monitor, And servo signals sent to each of the channels and it become so set function should be. In this paper, the laver drying device, prior to the laver thickness measurement and control devices that rely on the experience of existing workers directly laver manually adjust the thickness of the lever, but the lever by each channel relative to the actuator by installing was to improve the quality. In addition, The effect of productivity gains and labor savings are.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.477-477
• /
• 2008

For more than three decades, the gate dielectrics in CMOS devices are $SiO_2$ because of its blocking properties of current in insulated gate FET channels. As the dimensions of feature size have been scaled down (width and the thickness is reduced down to 50 urn and 2 urn or less), gate leakage current is increased and reliability of $SiO_2$ is reduced. Many metal oxides such as $TiO_2$, $Ta_2O_4$, $SrTiO_3$, $Al_2O_3$, $HfO_2$ and $ZrO_2$ have been challenged for memory devices. These materials posses relatively high dielectric constant, but $HfO_2$ and $Al_2O_3$ did not provide sufficient advantages over $SiO_2$ or $Si_3N_4$ because of reaction with Si substrate. Recently, $HfO_2$ have been attracted attention because Hf forms the most stable oxide with the highest heat of formation. In addition, Hf can reduce the native oxide layer by creating $HfO_2$. However, new gate oxide candidates must satisfy a standard CMOS process. In order to fabricate high density memories with small feature size, the plasma etch process should be developed by well understanding and optimizing plasma behaviors. Therefore, it is necessary that the etch behavior of $HfO_2$ and plasma parameters are systematically investigated as functions of process parameters including gas mixing ratio, rf power, pressure and temperature to determine the mechanism of plasma induced damage. However, there is few studies on the the etch mechanism and the surface reactions in $BCl_3$ based plasma to etch $HfO_2$ thin films. In this work, the samples of $HfO_2$ were prepared on Si wafer with using atomic layer deposition. In our previous work, the maximum etch rate of $BCl_3$/Ar were obtained 20% $BCl_3$/ 80% Ar. Over 20% $BCl_3$ addition, the etch rate of $HfO_2$ decreased. The etching rate of $HfO_2$ and selectivity of $HfO_2$ to Si were investigated with using in inductively coupled plasma etching system (ICP) and $BCl_3/Cl_2$/Ar plasma. The change of volume densities of radical and atoms were monitored with using optical emission spectroscopy analysis (OES). The variations of components of etched surfaces for $HfO_2$ was investigated with using x-ray photo electron spectroscopy (XPS). In order to investigate the accumulation of etch by products during etch process, the exposed surface of $HfO_2$ in $BCl_3/Cl_2$/Ar plasma was compared with surface of as-doped $HfO_2$ and all the surfaces of samples were examined with field emission scanning electron microscopy and atomic force microscope (AFM).

• Journal of the Korean Vacuum Society
• /
• v.17 no.6
• /
• pp.518-522
• /
• 2008

The miniaturization of device size and multilevel interlayers have been developed by ULSI circuit devices. These submicron processes cause serious problems in conventional metallization due to the solubility of silicon and metal at the interface, such as an increasing contact resistance in the contact hole and interdiffusion between metal and silicon. Therefore it is necessary to implement a barrier layer between Si and metal. Thus, the size of multilevel interconnection of ULSI devices is critical metallization schemes, and it is necessary reduce the RC time delay for device speed performance. So it is tendency to study the Cu metallization for interconnect of semiconductor processes. However, at the submicron process the interaction between Si and Cu is so strong and detrimental to the electrical performance of Si even at temperatures below $200^{\circ}C$. Thus, we suggest the tungsten-carbon-nitrogen (W-C-N) thin film for Cu diffusion barrier characterized by nano scale indentation system. Nano-indentation system was proposed as an in-situ and nanometer-order local stress analysis technique.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.2
• /
• pp.397-407
• /
• 2015

In this paper, we designed 1 chip IC for 3-axis gyroscope and 3-axis accelerometer used for various IoT/M2M mobile devices such as smartphone, wearable device and etc. We especially focused on analysis of gyroscope noise and proposed new architecture for removing various noise generated by gyroscope MEMS and IC. Gyroscope, accelerometer and geo-magnetic sensors are usually used to detect user motion or to estimate moving distance, direction and relative position. It is very important element to designing a low noise IC because very small amount of noise may be accumulated and affect the estimated position or direction. We made a mathematical model of a gyroscope sensor, analyzed the frequency characteristics of MEMS and circuit, designed a low noise, compact and low power 1 chip 6-axis inertial sensor IC including 3-axis gyroscope and 3-axis accelerometer. As a result, designed IC has 0.01dps/${\sqrt{Hz}}$ of gyroscope sensor noise density.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.9
• /
• pp.1026-1037
• /
• 2016

3rd Generation Partnership Project (3GPP) is the progressing standardization of the narrowband IoT (NB-IoT) system to support massive devices for the Internet of Things (IoT) services. The NB-IoT system uses a coverage class technique to increase the performance of the NB-IoT system while serving massive devices in very wide coverage area. A moving device can change the coverage class according to the distance or the channel state between the base station and the moving device. However, in the conventional NB-IoT standard, the performance of the NB-IoT system degrades because the coverage class is changed based on the fixed criterion. This paper proposes the coverage class adaptation schemes to increase the performance of the NB-IoT system by dynamically change the coverage class according to the location or the channel state of the device. Simulation results show that the proposed coverage class adaptation scheme decreases both the signaling overhead and the PDCCH decoding error rate in comparison with the conventional coverage class adaptation scheme in the 3GPP standard.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.3
• /
• pp.201-206
• /
• 2019

This report constitutes the first demonstration in Korea of single-crystal lateral gallium oxide ($Ga_2O_3$) as a metal-oxide-semiconductor field-effect-transistor (MOSFET), with a breakdown voltage in excess of 480 V. A Si-doped channel layer was grown on a Fe-doped semi-insulating ${\beta}-Ga_2O_3$ (010) substrate by molecular beam epitaxy. The single-crystal substrate was grown by the edge-defined film-fed growth method and wafered to a size of $10{\times}15mm^2$. Although we fabricated several types of power devices using the same process, we only report the characterization of a finger-type MOSFET with a gate length ($L_g$) of $2{\mu}m$ and a gate-drain spacing ($L_{gd}$) of $5{\mu}m$. The MOSFET showed a favorable drain current modulation according to the gate voltage swing. A complete drain current pinch-off feature was also obtained for $V_{gs}<-6V$, and the three-terminal off-state breakdown voltage was over 482 V in a $L_{gd}=5{\mu}m$ device measured in Fluorinert ambient at $V_{gs}=-10V$. A low drain leakage current of 4.7 nA at the off-state led to a high on/off drain current ratio of approximately $5.3{\times}10^5$. These device characteristics indicate the promising potential of $Ga_2O_3$-based electrical devices for next-generation high-power device applications, such as electrical autonomous vehicles, railroads, photovoltaics, renewable energy, and industry.

• Korean Journal of Community Nutrition
• /
• v.24 no.2
• /
• pp.137-151
• /
• 2019

Objectives: The rapidly changing dietary environment requires a study that addresses the status of middle and high school students regarding their consumption of convenience food sold at convenience stores. Methods: This study examined adolescents' lifestyle patterns, dietary habits, and status of consuming convenience food at convenience stores. A total of 659 students (329 middle school students and 330 high school students) in Incheon participated in this questionnaire survey. Results: The mean age of the subjects was 13.7 years for the middle school students, and 16.6 years for the high school students. The gender and grade distributions in the middle and high school students were similar. The middle school students reported that they spent more time using electronic devices (p<0.001) or watching TV (p<0.001) than high school students. More than 60% of middle and high school students consumed convenience food at convenience stores without statistical difference between the two groups. The main reason for consuming convenience food from convenience stores was its convenience followed by taste in both groups. Despite the high frequency of consuming convenience food, the students rarely checked the nutrition labels at the time of purchase. On the other hand, they were still most concerned about the nutritional value of the convenience foods when they consumed convenience foods. The most frequently consumed convenience food was ramyon in both groups. Significant positive correlations were observed between the frequency of consuming convenience food at convenience stores and lifestyle factors for the middle school students, including monthly allowance, time for using electronic devices, and number of private lessons. For the high school students, however, the only monthly allowance had a significant positive correlation with the consumption. Conclusions: Adolescents are increasingly exposed to convenience foods and relevant nutritional issues are a concern. Therefore, a dietary environment that is adequately formed for the healthy development of youth as well as systematic nutrient education that is appropriately designed for both middle and high school students is required.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.5
• /
• pp.538-549
• /
• 2019

This study suggests a new platform in which VI can communicate with their guardians who serve as a system administrator optimizing personal characteristics. In terms of interaction between platform components, this study can contribute to enhancing stability of walking by giving substantial information to VI through server processing and setups of guardians with real-time interaction to VI through server processing and setups of guardians with real-time interaction. Therefore, developing smart phone applications can facilitate both portability and cost effectiveness, by the users' downloading the application and registration. In terms of guardians' cost, this system is cost-effective because they can access to the administration system through personal computers or smart phones, not through specialized system devices. This system is web-based, which automatically communicates with the surroundings of, such as provides the guardians with the necessary information or approaches to the danger through IoT devices, which results in enhancing safety. Moreover, it is possible for guardians to utilize the personalized platform since the system not only senses personal characteristics but also sends a number of information to VI. a new platform makes it possible for guardians to provide electronic support and interaction with the application with the application users, which contributes to systematic and safe walk for VI.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.2
• /
• pp.164-177
• /
• 2022

Medical device usability evaluation refers to the evaluation of medical devices through actual users before the final prototype production is completed. IEC 62366, one of the international safety standards for electronic medical devices, is a standard that must be applied to obtain medical device licenses in major advanced countries such as Europe and the United States. In Korea, through the Ministry of Food and Drug Safety's notice, from January 2021, sequential application by grade has been implemented. In this study, 15 participant specialists were recruited through the Incheon G University Hospital Medical Device Convergence Center for formative evaluation during user suitability evaluation of the focused ultrasound stimulation system being developed by Icleo Co., Ltd., and the test was conducted through joint scenario development. . In the result of task performance, the performance rate was 90.67%, and after the completion of the performance, 86.67% of 'Easy user interface' and 94% of 'Identification/Readability/Understanding of information' questions in the participant survey results analysis by question. The response rate was above average.

• Journal of the Korean Society of Radiology
• /
• v.17 no.3
• /
• pp.411-416
• /
• 2023

The purpose of this study is to investigate the utilization of major learning tools among radiology science students and assess the accuracy of a conversational artificial intelligence service program, specifically a chatbot, in the context of the national radiologic technologist licensing exam. The survey revealed that 84.3% of radiology science students actively utilize electronic devices during their learning process. In addition, 104 out of 140 respondents said they use search engines as a top priority for efficient data collection while studying. When asked about their awareness of chatbots, 80% of participants responded affirmatively, and 22.9% reported having used chatbots for academic purposes at least once. From 2018 to 2022, exam questions from the first and second periods were presented to the chatbot for answers. The results showed that ChatGPT's accuracy in answering first period questions increased from 48.28% to 60%, while for second period questions, it increased from 50% to 62.22%. Bing's accuracy in answering first period questions improved from 55% to 64.55%, and for second period questions, it increased from 48% to 52.22%. The study confirmed the general trend of radiology science students utilizing electronic devices for learning and obtaining information through the internet. However, conversational artificial intelligence service programs in the field of radiation science face challenges related to accuracy and reliability, and providing perfect solutions remains difficult, highlighting the need for continuous development and improvement.